scholarly journals Hydrothermal Synthesis of SBA-15 Using Sodium Silicate Derived from Coal Gangue

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Jing Wang ◽  
Li Fang ◽  
Fangqin Cheng ◽  
Xiaofang Duan ◽  
Rongming Chen
Keyword(s):  
Hydrothermal Synthesis ◽  
Pore Size ◽  
Surface Area ◽  
Sodium Silicate ◽  
Mesoporous Materials ◽  
Pore Volume ◽  
Coal Gangue ◽  
Hydrothermal Route ◽  
Hydrothermal Temperature ◽  
Ordered Mesoporous

Well-ordered SBA-15 was prepared with a hydrothermal route by sodium silicate derived from coal gangue. The as-prepared sample was analyzed by SAXRD, BET, TEM, and SEM, respectively. The results indicate that at a low hydrothermal temperature of 100∘C the well-ordered mesoporous SBA-15 could be synthesized. The surface area, pore volume, and pore size of the sample are 552 m2/g, 0.54 cm3/g, and 7.0 nm, respectively. It is suggested that coal gangue could be used in obtaining an Si source to prepare mesoporous materials, such as SBA-15.

scholarly journals Morphology-Controllable Hydrothermal Synthesis of Zirconia with the Assistance of a Rosin-Based Surfactant

2019 ◽  
Vol 9 (19) ◽  
pp. 4145 ◽  
Author(s):  
Chen Guo ◽  
Peng Wang ◽  
Shengliang Liao ◽  
Hongyan Si ◽  
Shangxing Chen ◽  
...  
Keyword(s):  
Hydrothermal Synthesis ◽  
Aqueous Solutions ◽  
Pore Size ◽  
Surface Area ◽  
Calcination Temperature ◽  
Pore Volume ◽  
Crystal Size ◽  
Edge Angle ◽  
Large Pore Volume ◽  
Hollow Cube

With the assistance of a rosin-based surfactant, dehydroabietyltrimethyl ammonium bromine (DTAB), well-dispersed hollow cube-like zirconia particles were firstly synthesized by the hydrothermal treatment of ZrOCl2 aqueous solutions. The introduction of DTAB is crucial for improving the dispersion and regularity of the as-synthesized sample. After calcination, the crystal size of the calcined samples increased, and the edge angle of the cube-like particles became round accordingly. Finally, a hollow spherical morphology was formed for the sample calcined at 923 K. The as-synthesized sample showed big surface area of 146.78 m2/g and large pore volume of 0.23 cm3/g. With the increase of calcination temperature, the surface area and pore volume of the samples decreased significantly, and the pore size increased accordingly.

scholarly journals Synthesis and mechanism of aluminum silicate mesoporous materials by F108 template

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Zhijun Ma ◽  
Jing Gao ◽  
Xingyuan Weng ◽  
Shuai Yang ◽  
Kai Peng
Keyword(s):  
Pore Size ◽  
Sodium Hydroxide ◽  
Surface Area ◽  
Mesoporous Materials ◽  
Pore Volume ◽  
Average Pore Size ◽  
Molar Ratio ◽  
Aluminum Silicate ◽  
Synthetic Material ◽  
Average Pore

Abstract Aluminosilicate mesoporous materials were synthesized using F108 template (polyethylene glycol-polypropylene glycolpolyethylene glycol) at a concentration of 0.034 g/ml and the molar ratio of Al2O3 to SiO2 was 0.09. The products were then characterized using nitrogen adsorption/desorption tests, scanning electron microscopy (SEM), and X-ray diffraction (XRD). The effects of various crystallization temperatures as well as sodium hydroxide concentrations on the average diameter, pore volume, surface area, and morphology of the synthetic material were analyzed. Results showed that a sodium hydroxide concentration of 11 mol/L and a crystallization temperature of 130 °C produced a synthetic material with regular pore size and homogeneous arrangement including a specific surface area of 137.62 m2/g, an average pore volume of 0.27 cm3/g, along with an average pore size of 15.33 nm.

The relationship between geotechnical index properties and the pore-size distribution of compacted clayey silts

2015 ◽  
Vol 22 (6) ◽  
Author(s):  
Nazile Ural
Keyword(s):  
Specific Surface ◽  
Pore Size Distribution ◽  
Pore Size ◽  
Size Distribution ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Correlation Coefficients ◽  
Liquid Limit ◽  
Index Properties

AbstractIn this study, the relationships between geotechnical index properties and the pore-size distribution of compacted natural silt and artificial soil mixtures, namely, silt with two different clays and three different clay percentages (10%, 20%, and 40%), were examined and compared. Atterberg’s limit tests, standard compaction tests, mercury intrusion porosimetry, X-ray diffraction, scanning electron microscopy (SEM) analysis, and Brunauer-Emmett-Teller specific surface analysis were conducted. The results show that the liquid limit, the cumulative pore volume, and specific surface area of artificially mixed soils increase with an increase in the percentage of clay. The cumulative pore volume and specific surface area with geotechnical index properties were compared. High correlation coefficients were observed between the specific areas and both the liquid limit and the plasticity index, as well as between the cumulative pore volume and both the clay percentage and the

Investigation of the methane adsorption characteristics of marine organic-rich shale: A case study of the lower Cambrian Niutitang Shale in the Fenggang block, northern Guizhou Province, South China

2018 ◽  
Vol 6 (4) ◽  
pp. T819-T833 ◽  
Author(s):  
Yang Gu ◽  
Wenlong Ding ◽  
Min Yin ◽  
Ruyue Wang ◽  
Baocheng Jiao ◽  
...  
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Adsorption Capacity ◽  
Surface Area ◽  
South China ◽  
Pore Volume ◽  
Lower Cambrian ◽  
Methane Adsorption ◽  
Guizhou Province ◽  
Average Value

The marine shale in South China has great gas exploration potential, and exploration in the Sichuan Basin has been successful, but the degree of exploration remains low in the Guizhou Province. We used organic geochemical analyses (total organic carbon content and kerogen type), scanning electron microscopy (SEM), field emission SEM, nuclear magnetic resonance (NMR), X-ray diffraction analysis, and low-temperature [Formula: see text] and [Formula: see text] adsorption experimental methods to study the micropore types and pore structures and their effects on the methane adsorption capacity of organic-rich shales found in the Fenggang block in northern Guizhou Province. The results indicate that the microscopic surface porosity of the lower Cambrian Niutitang Formation ranges from 2.88% to 5.34%, with an average value of 3.86%. Based on nitrogen adsorption methods, the range of the average pore size distribution is 4.6–9.491 nm, with an average value of 6.68 nm. All of the samples exhibit significant unimodal distributions. The main pore size is less than 10 nm, and these pores account for most of the mesopore volume, which is generally consistent with the NMR results. The methane adsorption capacity of the shale samples gradually increases in the range of 0–8 MPa at 30°C and reaches a maximum at approximately 10 MPa. Positive correlations were found between the gas content and specific surface area, total pore volume, and micropore volume. These strong correlations indicate that the Niutitang Shale has a high specific surface area, a high pore volume, and narrow-diameter pores, demonstrating that it has a high gas adsorption capacity. The results of this study provide valuable information regarding the adsorption characteristics of marine shales and the factors that affect those characteristics.

High specific surface area ordered mesoporous silica COK-12 with tailored pore size

2019 ◽  
Vol 280 ◽  
pp. 133-143 ◽  
Author(s):  
Laura M. Henning ◽  
Diego Díaz Cubas ◽  
Maria G. Colmenares ◽  
Johannes Schmidt ◽  
Maged F. Bekheet ◽  
...  
Keyword(s):  
Mesoporous Silica ◽  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
High Specific Surface Area ◽  
Ordered Mesoporous Silica ◽  
Ordered Mesoporous

scholarly journals Targeted therapeutic effect against the breast cancer cell line MCF-7 with a CuFe2O4/silica/cisplatin nanocomposite formulation

2019 ◽  
Vol 10 ◽  
pp. 2217-2228 ◽  
Author(s):  
B Rabindran Jermy ◽  
Vijaya Ravinayagam ◽  
Widyan A Alamoudi ◽  
Dana Almohazey ◽  
Hatim Dafalla ◽  
...  
Keyword(s):  
Breast Cancer ◽  
Pore Size ◽  
Cell Line ◽  
Surface Area ◽  
Breast Cancer Cell Line ◽  
Pore Volume ◽  
Cancer Cell Line ◽  
Copper Ferrite ◽  
X Ray ◽  
Mcf 7

The combination of magnetic nanoparticles with a porous silica is a composite that has attracted significant attention for potential multifunctional theranostic applications. In this study, 30 wt % CuFe2O4 was impregnated into a matrix of monodispersed spherical hydrophilic silica (HYPS) nanoparticles through a simple dry impregnation technique. The chemotherapy drug cisplatin was loaded through electrostatic equilibrium adsorption over 24 h in normal saline solution. The presence of cubic spinel CuFe2O4 on HYPS was confirmed through powder X-ray diffraction (PXRD), Fourier transform infrared spectroscopy (FTIR) and diffuse reflectance UV–vis spectroscopy (DR UV–vis) analysis. The HYPS particles showed a surface area of 170 m2/g, pore size of 8.3 nm and pore volume of 0.35 cm3/g. The cisplatin/CuFe2O4/HYPS nanoformulation showed the accumulation of copper ferrite nanoparticles on the surface and in the pores of HYPS with a surface area of 45 m2/g, pore size of 16 nm and pore volume of 0.18 cm3/g. Transmission electron microscopy (TEM) and energy dispersive X-ray (EDX) mapping analysis showed the presence of homogeneous silica particles with nanoclusters of copper ferrite distributed on the HYPS support. Vibrating sample magnetometry (VSM) analysis of CuFe2O4/HYPS showed paramagnetic behavior with a saturated magnetization value of 7.65 emu/g. DRS UV–vis analysis revealed the functionalization of cisplatin in tetrahedral and octahedral coordination in the CuFe2O4/HYPS composite. Compared to other supports such as mesocellular foam and silicalite, the release of cisplatin using the dialysis membrane technique was found to be superior when CuFe2O4/HYPS was applied as the support. An in vitro experiment was conducted to determine the potential of CuFe2O4/HYPS as an anticancer agent against the human breast cancer cell line MCF-7. The results show that the nanoparticle formulation can effectively target cancerous cells and could be an effective tumor imaging guide and drug delivery system.

Synthesis and Preparation of Al-MCM-41 Mesoporous Materials Using Oil Shale Residue

2019 ◽  
Vol 944 ◽  
pp. 1192-1198
Author(s):  
Rong Wang ◽  
Zhi Xiang Lin ◽  
Yang Zhao ◽  
Xiao Dong Xu ◽  
Yan Xi Deng
Keyword(s):  
Surface Area ◽  
Mesoporous Materials ◽  
Pore Volume ◽  
Oil Shale ◽  
Bet Surface Area ◽  
Ammonium Bromide ◽  
Scale Production ◽  
Scanning Electron Micrographs ◽  
One Step ◽  
Mcm 41

An Al-supported cage-like mesoporous silica type MCM-41 has been prepared using a simple one-step synthetic procedure using oil shale residue and CTAB(Hexadecyl trimethyl Ammonium Bromide) as the template. The effects of temperature on the porosity, structure and surface area of Al-MCM-41 mesoporous materials were characterized by X-ray powder diffraction, N2adsorption desorption, scanning electron micrographs (SEM), transmission electron microscopy (TEM) techniques and Fourier transform infrared spectroscopy (FT-IR). The results indicated that temperature was a key to the characteristics of Al-MCM-41 materials, and when the temperature up to 333 K, Al-MCM-41 exhibited excellent characteristics with high degree of order, high surface area and pore volume. The one-step hydrothermal synthesized MCM-41 mesoporous material possessed high BET surface area, high pore size and high pore volume. They are respectively 835.1 m2/g, 32.6 Å and 1.22 cm3/g under the condition of the Si : Al =78:1, pH =10, crystallization temperature was 333K, crystallization time was 48h and calcination at 823 K for 5 h in air. All the results indicated the possibility of using oil shale residue as silicon and aluminum source to produce Al-MCM-41, and gave us a new way to recycle a solid waste. As well as this made it impossible to large-scale production of Al-MCM-41. Keywords: Al-MCM-41 mesoporous materials, oil shale residue, one-step synthesis

Non-hydrothermal synthesis of mesoporous materials using sodium silicate from coal fly ash

2007 ◽  
Vol 101 (2-3) ◽  
pp. 344-351 ◽  
Author(s):  
M. Halina ◽  
S. Ramesh ◽  
M.A. Yarmo ◽  
R.A. Kamarudin
Keyword(s):  
Fly Ash ◽  
Hydrothermal Synthesis ◽  
Sodium Silicate ◽  
Mesoporous Materials ◽  
Coal Fly Ash

The Influence of Sinterng Temperature on the Phase, Microstructure and Textual Properties of Hollow Hydroxyapatite Microspheres

2011 ◽  
Vol 239-242 ◽  
pp. 2274-2279 ◽  
Author(s):  
Ying Chun Wang ◽  
Wen Hai Huang ◽  
Ai Hua Yao ◽  
De Ping Wang
Keyword(s):  
Specific Surface ◽  
Pore Size ◽  
Surface Area ◽  
Specific Surface Area ◽  
Pore Volume ◽  
Sintering Temperature ◽  
Total Pore Volume ◽  
Precipitation Method ◽  
Simple Method ◽  
Air Atmosphere

A simple method to prepare hollow hydroxyapatite (HAP) microspheres with mespores on the surfaces is performed using a precipitation method assisted with Li2O-CaO-B2O3(LCB) glass fabrication process. This research is concerned with the effect of sintering temperature on the microstructure evolution, phase purity, surface morphology, specific surface area, and porosity after sintering process. The microspheres were sintered in air atmosphere at temperatures ranging from 500 to 900 °C. The starting hollow HAP microspheres and the sintered specimens were characterized by scanning electron microscope, X-ray diffractometer, specific surface area analyzer, and Hg porosimetry, respectively. The as-prepared microspheres consisted of calcium deficient hydroxyapatite. The results showed that the as-prepared hollow HAP microspheres had the highest specific surface areas, and the biggest total pore volume. The pore size distribution of the as-prepared hollow HAP microspheres were mainly the mesopores in the range of 2～40 nm. The specific surface area and total pore volume of hollow HAP microspheres decreased with increasing sintering temperature. Whereas the mean pore size increased with increasing sintering temperature. It showed that at 700°C, Ca-dHAP decomposes into a biphasic mixture of HAP and β-calcium phosphate(TCP).

Characterization and Assessment of Cockle Shell as Potential CO2 Adsorbents

2014 ◽  
Vol 625 ◽  
pp. 685-689 ◽  
Author(s):  
Nurulhuda Azmi ◽  
Suzana Yusup ◽  
Khalik M. Sabil
Keyword(s):  
High Temperature ◽  
Surface Area ◽  
Mesoporous Materials ◽  
Pore Volume ◽  
Material Characterization ◽  
Calcination Process ◽  
Crucial Step ◽  
Cockle Shell ◽  
High Temperature Calcination ◽  
Better Than

Material characterization is a crucial step to ensure the characteristics and properties of the samples are comparable to the standard adsorbent and suitable for CO2 adsorption. The objective of this work is to characterize natural calcium based materials for CO2 adsorption which are obtained from waste cockle shells. Characterization analyses are conducted by using XRD, BET and FESEM. Material characterization indicates that raw cockle shell is made up of aragonite and needle-like structure. It is also shown that CaCO3 can be decomposed to CaO through high temperature calcination process. Through physisorption analysis, the samples are classified as mesoporous materials and it is shown that calcined cockle shell is better than raw cockle shell in term of surface area and pore volume. The results proved that calcium based materials could be successfully employed as sorbent for CO2 separation.

Sign in / Sign up

Export Citation Format

Share Document