scholarly journals Synthesis and Characterization of Pyrochlore Bi2Sn2O7Doping with Praseodymium by Hydrothermal Method and Its Photocatalytic Activity Study

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Weicheng Xu ◽  
Guangyin Zhou ◽  
Jianzhang Fang ◽  
Zhang Liu ◽  
YunFang Chen ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Electron Microscope ◽  
Visible Light ◽  
Hydrothermal Method ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray ◽  
Transmission Electron ◽  
20 Nm ◽  
Adsorption Desorption

Praseodymium doped Bi2Sn2O7(BSO), as a visible-light responsive photocatalyst, was prepared by a hydrothermal method with different dopant contents. The as-prepared photocatalysts were investigated by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscope (TEM), N2adsorption-desorption isotherm, X-ray photoelectron spectroscopy analysis (XPS), and UV-Vis diffuse reflectance spectroscopy (DRS). The photocatalytic activity of prepared catalysts was evaluated by the degradation of Rhodamine Bextra (RhB) and 2,4-dichlorophenol (2,4-DCP) in aqueous solution under visible light irradiation. It was found that Pr doping inhibited the growth of crystalline size and the as-prepared materials were small in size (10–20 nm). In our experiments, Pr-doped BSO samples exhibited enhanced visible-light photocatalytic activity compared to the undoped BSO, and the optimal dopant amount of Pr was 1.0 mol% for the best photocatalytic activity. On the basis of the calculated PL spectra, the mechanism of enhanced photocatalytic activity has been discussed.

scholarly journals Photocatalytic Degradation of Estriol Using Iron-Doped TiO2 under High and Low UV-Irradiation

2018 ◽  
Author(s):  
Irwing M. Ramírez-Sánchez ◽  
Erick R. Bandala
Keyword(s):  
Photocatalytic Activity ◽  
Electron Microscope ◽  
Uv Irradiation ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Bet Surface Area ◽  
Doped Tio2 ◽  
X Ray ◽  
Transmission Electron ◽  
Iron Doped

Iron Doped TiO2 nanoparticles (Fe-TiO2) were synthesized and photocatalitically investigated under high and low fluence values of UV-radiation. The Fe-TiO2 physical characterization was performed using X-ray Powder Diffraction (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, Transmission Electron Microscope (TEM), Scanning Electron Microscope (SEM), Diffuse Reflectance Spectroscopy (DRS), and X-Ray Photoelectron Spectroscopy (XPS) technique. The XPS evidenced that ferric ion (Fe3+) was in the lattice of TiO2 and co-dopants no intentionally added were also present due to the precursors of the synthetic method. The Fe3+ concentration played a key role in the photocatalytic generation of hydroxyl radical (•OH) and estriol (E3) degradation. Fe-TiO2 materials accomplished E3 degradation, and it was found that the catalyst with 0.3 at. % content of Fe (0.3 Fe-TiO2) enhanced the photocatalytic activity under low UV-irradiation compared with no intentionally Fe-added TiO2 (zero-iron TiO2) and Aeroxide® TiO2 P25. Furthermore, the enhanced photocatalytic activity of 0.3 Fe-TiO2 under low UV-irradiation may have applications when radiation intensity must be controlled, as in medical applications, or when strong UV absorbing species are present in water.

scholarly journals Improved Visible Light Photocatalytic Activity for TiO2Nanomaterials by Codoping with Zinc and Sulfur

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Qianzhi Xu ◽  
Xiuying Wang ◽  
Xiaoli Dong ◽  
Chun Ma ◽  
Xiufang Zhang ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Sunlight Irradiation ◽  
X Ray ◽  
Transmission Electron ◽  
Photoinduced Charge

S/Zn codoped TiO2nanomaterials were synthesized by a sol-gel method. X-ray diffraction, UV-vis diffuse reflectance spectroscopy, transmission electron microscopy, photoluminescence spectroscopy, and X-ray photoelectron spectroscopy were used to characterize the morphology, structure, and optical properties of the prepared samples. The introduction of Zn and S resulted in significant red shift of absorption edge for TiO2-based nanomaterials. The photocatalytic activity was evaluated by degrading reactive brilliant red X-3B solution under simulated sunlight irradiation. The results showed S/Zn codoped TiO2exhibited higher photocatalytic activity than pure TiO2and commercial P25, due to the photosynergistic effect of obvious visible light absorption, efficient separation of photoinduced charge carriers, and large surface area. Moreover, the content of Zn and S in the composites played important roles in photocatalytic activity of TiO2-based nanomaterials.

Dye-Sensitized-Assisted, Enhanced Photocatalytic Activity of TiO2/Bi4V2O11

NANO ◽  
2018 ◽  
Vol 13 (03) ◽  
pp. 1850028 ◽  
Author(s):  
Mengjun Liang ◽  
Zhiyuan Yang ◽  
Ying Mei ◽  
Haoran Zhou ◽  
Shuijin Yang
Keyword(s):  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dye Sensitized ◽  
Transmission Electron ◽  
Efficient Charge ◽  
Degradation Activity ◽  
Adsorption Desorption

In this study, the TiO2/Bi4V2O[Formula: see text] nanocomposite photocatalysts were prepared by loading different amount of TiO2 nanoparticles onto the surface of Bi4V2O[Formula: see text] nanospheres via a facile hydrothermal method. Afterwards, the as-synthesized samples were characterized by high-resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD), N2 adsorption–desorption isotherms, X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectroscopy (DRS) and photocurrent techniques. The optimal TiO2/Bi4V2O[Formula: see text] composite with 20[Formula: see text]wt.% TiO2 loading (TB2) exhibited the best photocatalytic activity, which could degrade almost RhB completely within 30[Formula: see text]min under visible light irradiation. The enhanced photocatalytic activity of TiO2/Bi4V2O[Formula: see text] composites for RhB degradation could be mainly ascribed to the efficient charge separation over dye-induced sensitized and the increased specific surface area. Also, the photocatalytic activities of TiO2/Bi4V2O[Formula: see text] for CIP degradation were tested. After five consecutive recycling experiments, the photocatalytic degradation activity of TB2 could still reach 99% which indicated that the catalysts had superior stability. Based on the experimental and bandgap calculations, a possible photocatalytic mechanism of TiO2/Bi4V2O[Formula: see text] for RhB degradation was proposed.

Improved visible-light photocatalytic activity of sodium tantalum oxide via biomass-derived silk fibroin doping

2018 ◽  
Vol 89 (7) ◽  
pp. 1332-1339
Author(s):  
Yehua Sun ◽  
Yuzhuo Luo ◽  
Yaofeng Zhu ◽  
Yaqin Fu
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Activity ◽  
Visible Light ◽  
Silk Fibroin ◽  
Photoelectron Spectroscopy ◽  
Structural Changes ◽  
Diffuse Reflectance Spectroscopy ◽  
Hydrothermal Process ◽  
X Ray ◽  
Transmission Electron

Biomass-derived silk fibroin (SF)-doped NaTaO3 catalysts were successfully synthesized by a simple hydrothermal process using SF as the dopant. The as-prepared samples were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and ultraviolet-visible diffuse reflectance spectroscopy (UV-vis DRS) analyses. The samples were tested as photocatalysts in the degradation of methylene blue under UV and visible light. XRD results showed the monoclinic structure of NaTaO3 lacking significant structural changes after anion doping. SEM and TEM images revealed the nanocubic morphology of the samples, the crystal particle sizes of which were about 100–300 nm. The XPS spectrum showed the peak of Ta4p3&N1s, indicating the combination of N and Ta. The UV-vis DRS results of the samples revealed a cut-off edge that red shifted from 315 nm of the pure NaTaO3 to 324 nm of the SF-doped counterpart. SF doping helped narrow the band gap and rendered the prepared sample sensitive to visible light. Under UV and visible-light irradiation, SF-doped NaTaO3 exhibited higher photocatalytic activity than that the undoped compound. SF-doped NaTaO3 samples also exhibited excellent stability during the recycling photocatalytic process.

scholarly journals Self-Assembly of TiO2/CdS Mesoporous Microspheres with Enhanced Photocatalytic Activity via Hydrothermal Method

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
Sujing Yu ◽  
Juncheng Hu ◽  
Jinlin Li
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Photocatalytic Activity ◽  
Hydrothermal Method ◽  
Photoelectron Spectroscopy ◽  
Self Assembly ◽  
Diffuse Reflectance Spectroscopy ◽  
X Ray ◽  
Transmission Electron ◽  
Mesoporous Microspheres

Self assembly of TiO2/CdS mesoporous microspheres was synthesized via hydrothermal method. The samples were characterized by X-ray powder diffraction (XRD), ultraviolet-visible diffuse reflectance spectroscopy (DRS), transmission electron microscopy (TEM), energy-dispersive spectroscopy analysis (EDS), high-resolution transmission electron microscopy (HRTEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), and photoluminescence spectra (PL). The as-synthesized TiO2/CdS mesoporous microspheres showed superior photocatalytic activity for the degradation of RhB under either visible light or simulated sunlight irradiation; the 10 wt% TiO2/CdS sample showed the best performance. Moreover, this catalyst showed improved stability, and the activity did not decrease significantly after four recycles. The heterojunction between TiO2and CdS may be favorable for the transport of photoinduced electrons from CdS to TiO2. In addition, the mesoporous structure could increase the utilization of light energy and facilitate the diffusion of reactants and products during the photocatalytic reaction.

FeYO3@rGO nanocomposites: Synthesis, characterization and application in photooxidative degradation of atrazine under visible light

2021 ◽  
Vol 11 (5) ◽  
pp. 706-716
Author(s):  
Nada D. Al-Khthami ◽  
Tariq Altalhi ◽  
Mohammed Alsawat ◽  
Mohamed S. Amin ◽  
Yousef G. Alghamdi ◽  
...  
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Bandgap Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Structural Surface ◽  
Adsorption Desorption

Different organic pollutants have been remediated photo catalytically by applying perovskite photocatalysts. Atrazine (ATR) is a pesticide commonly detected as a pollutant in drinking, surface and ground water. Herein, FeYO3@rGO heterojunction was synthesized and applied for photooxidation decomposition of ATR. First, FeYO 3nanoparticles (NPs) were prepared via routine sol-gel. After that, FeYO3 NPs were successfully incorporated with different percentages (5, 10, 15 and 20 wt.%) of reduced graphene oxide (rGO) in the synthesis of novel FeYO3@rGO photocatalyst. Morphological, structural, surface, optoelectrical and optical characteristics of constructed materials were identified via X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Transmission electron microscopy (TEM), adsorption/desorption isotherms, diffusive reflectance (DR) spectra, and photoluminescence response (PL). Furthermore, photocatalytic achievement of the constructed materials was evaluated via photooxidative degradation of ATR. Various investigations affirmed the usefulness of rGO incorporation on the advancement of formed photocatalysts. Actually, novel nanocomposite containing rGO (15 wt.%) possessed diminished bandgap energy, as well as magnified visible light absorption. Furthermore, such nanocomposite presented exceptional photocatalytic achievement when exposed to visible light as ATR was perfectly photooxidized over finite amount (1.6 g · L-1) from the optimized photocatalyst when illuminated for 30 min. The advanced photocatalytic performance of constructed heterojunctions could be accredited mainly to depressed recombination amid induced charges. The constructed FeYO3@rGO nanocomposite is labelled as efficient photocatalyst for remediation of herbicides from aquatic environments.

scholarly journals Hydrothermal Synthesis of Iodine-Doped Nanoplates with Enhanced Visible and Ultraviolet-Induced Photocatalytic Activities

2012 ◽  
Vol 2012 ◽  
pp. 1-12 ◽  
Author(s):  
Jiang Zhang ◽  
Zheng-Hong Huang ◽  
Yong Xu ◽  
Feiyu Kang
Keyword(s):  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Oxygen Vacancies ◽  
Diffuse Reflectance Spectroscopy ◽  
Synergetic Effect ◽  
X Ray Diffraction ◽  
X Ray ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Photocatalytic Activities

The iodine-doped Bi2WO6(I-BWO) photocatalyst was prepared via a hydrothermal method using potassium iodide as the source of iodine. The samples were characterized by X-ray diffraction (XRD), scanning electron microscope (SEM), transmission electron microscopy (TEM) and selected area electron diffraction (SAED), X-ray photoelectron spectroscopy (XPS), UV-vis diffuse reflectance spectroscopy (DRS), and photoluminescence (PL) spectroscopy. The photocatalytic activity of I-BWO for the degradation of rhodamine B (RhB) was higher than that of pure BWO and I2-BWO regardless of visible light (>420 nm) or ultraviolet light (<400 nm) irradiation. The results of DRS analysis showed that the I-BWO and I2-BWO catalysts had narrower band gaps. XPS analysis proved that the multivalent iodine species including I0and were coadsorbed on the defect surface of Bi2WO6in I-BWO. The enhanced PL intensity revealed that a large number of defects of oxygen vacancies were formed by the doping of iodine. The enhanced photocatalytic activity of I-BWO for degradation of RhB was caused by the synergetic effect of a small crystalline size, a narrow band gap, and plenty of oxygen vacancies.

scholarly journals Preparation and Characterization of Defective TiO2. The Effect of the Reaction Environment on Titanium Vacancies Formation

Materials ◽  
2020 ◽  
Vol 13 (12) ◽  
pp. 2763
Author(s):  
Zuzanna Bielan ◽  
Szymon Dudziak ◽  
Agnieszka Sulowska ◽  
Daniel Pelczarski ◽  
Jacek Ryl ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Hydrothermal Reaction ◽  
High Photocatalytic Activity ◽  
Paramagnetic Resonance ◽  
X Ray ◽  
Light Activity ◽  
Cheap Alternative

Among various methods of improving visible light activity of titanium(IV) oxide, the formation of defects and vacancies (both oxygen and titanium) in the crystal structure of TiO2 is an easy and relatively cheap alternative to improve the photocatalytic activity. In the presented work, visible light active defective TiO2 was obtained by the hydrothermal reaction in the presence of three different oxidizing agents: HIO3, H2O2, and HNO3. Further study on the effect of used oxidant and calcination temperature on the physicochemical and photocatalytic properties of defective TiO2 was performed. Obtained nanostructures were characterized by X-ray diffractometry (XRD), specific surface area (BET) measurements, UV-Vis diffuse reflectance spectroscopy (DR-UV/Vis), photoluminescence spectroscopy (PL), X-ray photoelectron spectroscopy (XPS), and electron paramagnetic resonance (EPR) spectroscopy. Degradation of phenol as a model pollutant was measured in the range of UV-Vis and Vis irradiation, demonstrating a significant increase of photocatalytic activity of defective TiO2 samples above 420 nm, comparing to non-defected TiO2. Correlation of EPR, UV-Vis, PL, and photodegradation results revealed that the optimum concentration of HIO3 to achieve high photocatalytic activity was in the range of 20–50 mol%. Above that dosage, titanium vacancies amount is too high, and the obtained materials’ photoactivity was significantly decreased. Studies on the photocatalytic mechanism using defective TiO2 have also shown that •O2− radical is mainly responsible for pollutant degradation.

scholarly journals Defective TiO2 Core-Shell Magnetic Photocatalyst Modified with Plasmonic Nanoparticles for Visible Light-Induced Photocatalytic Activity

Catalysts ◽  
2020 ◽  
Vol 10 (6) ◽  
pp. 672 ◽  
Author(s):  
Zuzanna Bielan ◽  
Agnieszka Sulowska ◽  
Szymon Dudziak ◽  
Katarzyna Siuzdak ◽  
Jacek Ryl ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Phenol Degradation ◽  
Magnetic Core ◽  
Magnetic Photocatalyst ◽  
X Ray ◽  
Transmission Electron ◽  
First Time

In the presented work, for the first time, the metal-modified defective titanium(IV) oxide nanoparticles with well-defined titanium vacancies, was successfully obtained. Introducing platinum and copper nanoparticles (NPs) as surface modifiers of defective d-TiO2 significantly increased the photocatalytic activity in both UV-Vis and Vis light ranges. Moreover, metal NPs deposition on the magnetic core allowed for the effective separation and reuse of the nanometer-sized photocatalyst from the suspension after the treatment process. The obtained Fe3O4@SiO2/d-TiO2-Pt/Cu photocatalysts were characterized by X-ray diffractometry (XRD) and specific surface area (BET) measurements, UV-Vis diffuse reflectance spectroscopy (DR-UV/Vis), X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Further, the mechanism of phenol degradation and the role of four oxidative species (h+, e−, •OH, and •O2−) in the studied photocatalytic process were investigated.

VISIBLE LIGHT ACTIVE Cu2+/TiO2 NANOCATALYST FOR DEGRADATION OF DICHLORVOS

2012 ◽  
Vol 11 (05) ◽  
pp. 1250030 ◽  
Author(s):  
TESHOME ABDO SEGNE ◽  
SIVA RAO TIRUKKOVALLURI ◽  
SUBRAHMANYAM CHALLAPALLI
Keyword(s):  
Catalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Light Illumination ◽  
X Ray ◽  
Photo Catalytic Activity ◽  
Visible Light Active ◽  
Adsorption Desorption

The advantage of doping of TiO2 with copper has been utilized for enhanced degradation of pesticide under visible light irradiation. The sol–gel method has been undertaken for the synthesis of copper-doped TiO2 by varying the dopant loadings from 0.25 wt.% to 1.0 wt.% of Cu2+ . The doped samples were characterized by UV-Visible Diffuse Reflectance Spectroscopy (DRS), N2 adsorption–desorption (BET), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectrometry (EDS). The photocatalytic activity of the catalyst was tested by degradation of dichlorvos under visible light illumination. The results found that 0.75 wt.% of Cu2+ doped nanocatalysts have better photo catalytic activity than the rest of percentages doped, undoped TiO2 and Degussa P25. The reduction of band gap was estimated and the influence of the process parameters on photo catalytic activity of the catalyst has been explained.

Sign in / Sign up

Export Citation Format

Share Document