scholarly journals Mechanical Response of Al-1.09Mg2Si Alloy under Varying Mould and Thermal Ageing Conditions

2012 ◽  
Vol 2012 ◽  
pp. 1-7
Author(s):  
O. I. Sekunowo ◽  
G. I. Lawal ◽  
S. O. Adeosun
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Ambient Temperature ◽  
Mechanical Response ◽  
Ageing Time ◽  
Thermal Ageing ◽  
Alloy Ingot ◽  
Solution Treated ◽  
Crucible Furnace

Samples of the 6063 (Al-1.09Mg2Si) alloy ingot were melted in a crucible furnace and cast in metal and sand moulds, respectively. Standard tensile, hardness, and microstructural test specimens were prepared from cast samples, solution treated at 520∘C, soaked for 6 hrs, and immediately quenched at ambient temperature in a trough containing water to assume a supersaturated structure. The quenched specimens were then thermally aged at 175∘C for 3–7 hrs. Results show that at different ageing time, varied fractions of precipitates and intermetallics evolved in the specimens’ matrices which affect the resulting mechanical properties. The metal mould specimens aged for four hours (MTA-4) exhibited superior ultimate tensile strength of 247.8 MPa; microhardness, 68.5 HV; elongation, 28.2% . It is concluded that the extent of improvement in mechanical properties depends on the fractions, coherence, and distribution of precipitates along with the type of intermetallics developed in the alloy during ageing process.

Elevated Temperature Mechanical Behavior of Mg-Y-Zn Alloys

2007 ◽  
Vol 546-549 ◽  
pp. 237-240 ◽  
Author(s):  
Bin Chen ◽  
Dong Liang Lin ◽  
Xiao Qin Zeng ◽  
Chen Lu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Elevated Temperature ◽  
Ultimate Tensile Strength ◽  
Ambient Temperature ◽  
Mechanical Behavior ◽  
Gradual Increase ◽  
Yttrium Content ◽  
Zn Alloy ◽  
Zn Alloys

The elevated temperature mechanical behavior of Mg-Y-Zn alloys was investigated. It was found that the extruded Mg-Y-Zn alloy exhibited excellent mechanical properties both at ambient temperature and elevated temperature. With the increase of tensile temperature, the ultimate tensile strengths of Mg-Y-Zn alloys decreased and their elongations increased. The ultimate tensile strengths increased and elongations decreased with the increase of yttrium content. However, a gradual increase in the ultimate tensile strength and elongation both at ambient temperature and elevated temperature was obtained by increasing both yttrium and zinc contents. The fracture modes of Mg-Y-Zn alloys at different tensile temperature were also investigated.

Effect of Solution Treatment and Extrusion on the Microstructure and Mechanical Properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr Alloy

2011 ◽  
Vol 197-198 ◽  
pp. 1125-1128 ◽  
Author(s):  
Jing Jiang Nie ◽  
Liang Meng ◽  
Xiu Rong Zhu ◽  
Yong Dong Xu ◽  
Yue Yi Wu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Treatment Time ◽  
Solution Treatment ◽  
Solution Treated ◽  
Microstructure And Mechanical Properties ◽  
Combined Action ◽  
Strength And Ductility

The effect of the combined action of hot work and heat treatment on the microstructure and mechanical properties of a Mg-2Gd-Nd-0.4Zn-0.3Zr (wt. %) (E21) alloy was investigated. Results showed that the solution treatment time of the ingot played a great effect on the mechanical properties of the extruded alloy. With solution treating time of the ingot increasing, the tensile strength of the extruded alloy decreased gradually, but the elongation increased greatly. The best combination of strength and ductility was achieved for the extruded alloy after the ingot solution treated at 520°C for 3 h, extrusion at 400°C and aging at 200°C for 16 h, namely ultimate tensile strength = 331MPa and elongation = 7.1%.

scholarly journals Microstructure and Mechanical Properties of Aged and Hot Rolled AZ80 Magnesium Alloy Sheets

Crystals ◽  
2019 ◽  
Vol 9 (5) ◽  
pp. 239 ◽  
Author(s):  
Bing He ◽  
Yaobo Hu ◽  
Tianshuo Zhao ◽  
Qingshan Yao ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Ageing Time ◽  
Rolling Process ◽  
Second Phase ◽  
Texture Intensity ◽  
Microstructure And Mechanical Properties ◽  
The Matrix ◽  
Basal Type

This study focused on the effects of ageing for various time at 175 °C before hot rolling on microstructure and mechanical properties of AZ80 magnesium alloys. The amount of γ-Mg17Al12 increased in line with ageing time and during the rolling process could facilitate the fine grains and sub-grains, which resulted in an inhomogeneous or bimodal microstructure, and weakening basal-type texture intensity or occurrence of double-peak texture. However, a larger quantity of γ-Mg17Al12 distributed on the matrix in the alloy aged for 240 min, or the precipitates decorating the grain boundaries in the alloy aged for 75 min, were detrimental to the mechanical properties, and lower ultimate tensile strength with elongation were obtained in the two alloys as a result. When the alloy was aged for 200 min, it showed an optimum mechanical property with its yield strength of 281 MPa, ultimate tensile strength of 363 MPa and a medium elongation of 13.3%, which was mainly attributed to the interaction of the hard second phase particles with dislocation movement and the lowest basal-type texture intensity that favored the basal slip.

Statistical models for the mechanical properties of 3D printed external medical aids

2020 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Rafael Moreno ◽  
Diego Carou ◽  
Daniel Carazo-Álvarez ◽  
Munish Kumar Gupta
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Statistical Models ◽  
Mechanical Response ◽  
Content Type ◽  
Raster Angle ◽  
Medical Aids ◽  
3D Printed ◽  
Printing Parameters

Purpose 3D printing is gaining attention in the medical sector for the development of customized solutions for a wide range of applications such as temporary external implants. The materials used for the manufacturing process are critical, as they must provide biocompatibility and adequate mechanical properties. This study aims to evaluate and model the influence of the printing parameters on the mechanical properties of two biocompatible materials. Design/methodology/approach In this study, the mechanical properties of 3D-printed specimens of two biocompatible materials (ABS medical and PLActive) were evaluated. The influence of several printing parameters (infill density, raster angle and layer height) was studied and modelled on three response variables: ultimate tensile strength, deformation at the ultimate tensile strength and Young’s modulus. Therefore, statistical models were developed to predict the mechanical responses based on the selected printing parameters. Findings The used methodology allowed obtaining compact models that show good fit, particularly, for both the ultimate tensile strength and Young’s modulus. Regarding the deformation at ultimate tensile strength, this output was found to be influenced by more factors and interactions, resulting in a slightly less precise model. In addition, the influence of the printing parameters was discussed in the work. Originality/value The presented paper proposed the use of statistical models to select the printing parameters (infill density, raster angle and layer height) to optimize the mechanical response of external medical aids. The models will help users, researchers and firms to develop optimized solutions that can reduce material costs and printing time but guaranteeing the mechanical response of the parts.

The Study on Microstructures and Mechanical Properties of Heat Rolled and Solution-Treated Fe-26Mn-6Al-1C Steel

2012 ◽  
Vol 482-484 ◽  
pp. 1530-1533
Author(s):  
Ming Li Huang ◽  
Hua Ying Li ◽  
Hua Ding
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Room Temperature ◽  
Solution Treatment ◽  
Tensile Tests ◽  
Solution Treated ◽  
Sem And Tem ◽  
Hot Rolled

In the present work, mechanical properties and microstructures of hot-rolled and solution-treated Fe-26Mn-6Al-1C steel (6Al steel) were investigated. Tensile tests were carried out at room temperature. The samples were characterized by using XRD, OM, SEM and TEM. The results suggested that the microstructure of the hot rolled 6Al steel was fully austenitic. After solution treatment and deformation, the microstructure was still single austenite. With the increase of the solution treatment temperatures, the strength decreased and the elongation increased. After solution treated at 1100°C for 1h, the yield strength, ultimate tensile strength and elongation were 378MPa, 756MPa and 57%.

Microstructure and Mechanical Properties of As-Rolled Mg-Zn-Gd-Ca-Mn Sheets

2014 ◽  
Vol 788 ◽  
pp. 68-73
Author(s):  
Sheng Shuan Dongye ◽  
Hong Yan ◽  
Xing Hao Du ◽  
Rong Shi Chen
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Magnesium Alloy ◽  
Ultimate Tensile Strength ◽  
Ambient Temperature ◽  
Hot Rolling ◽  
Basal Texture ◽  
Microstructure And Mechanical Properties ◽  
Zn Concentration ◽  
Elongation To Failure

The Mg-(4,6)Zn-1Ca-1RE-0.5Mn magnesium alloy sheets were processed by hot rolling, and the effect of Zn concentration on the microstructure and mechanical properties was investigated using OM,SEM and XRD technique. The Mg-4Zn-1Ca-1RE-0.5Mn sheet exhibits excellent tensile properties at ambient temperature with ultimate tensile strength of 332MPa and elongation to failure of 4.5%. The notable mechanical properties were attributed to fine DRX grains and large deformed grains with intense basal texture.

Aging Behavior of Mg-9Gd-4Y-0.6Mn Alloy

2007 ◽  
Vol 546-549 ◽  
pp. 425-428 ◽  
Author(s):  
Zhen Zhen Deng ◽  
Xin Ming Zhang ◽  
Yun Lai Deng ◽  
Yang Xiao ◽  
Tian Cai Guo
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Tensile Test ◽  
Heat Resistance ◽  
Room Temperature ◽  
Hardness Measurement ◽  
Aging Behavior ◽  
Solution Treated

Microstructures and properties of rolled Mg-9Gd-4Y-0.6Mn（nominal wt%）sheets solution treated at 793K for 12h, and aged at various combinations of temperatures and time were investigated by hardness measurement, tensile test and TEM. The evolution of the precipitates and their effect on the mechanical properties of the pre-, peak-, and over-aged tempers were determined, and the optimal yield tensile strength (YTS) and ultimate tensile strength (UTS) were 276MPa and 287MPa at room temperature, respectively. It has been found that the addition of Mn into Mg-Gd-Y system contributes to block behavior of matrix diffuse and increase potential of heat resistance of the alloy.

Vibratory weld conditioning during gas tungsten arc welding of al 5052 alloy on the mechanical and micro-structural behavior

2020 ◽  
Vol 17 (6) ◽  
pp. 831-836
Author(s):  
M. Vykunta Rao ◽  
Srinivasa Rao P. ◽  
B. Surendra Babu
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Welded Joints ◽  
Great Influence ◽  
Welding Process ◽  
Microstructural Characterization ◽  
Content Type ◽  
Average Grain Size

Purpose Vibratory weld conditioning parameters have a great influence on the improvement of mechanical properties of weld connections. The purpose of this paper is to understand the influence of vibratory weld conditioning on the mechanical and microstructural characterization of aluminum 5052 alloy weldments. An attempt is made to understand the effect of the vibratory tungsten inert gas (TIG) welding process parameters on the hardness, ultimate tensile strength and microstructure of Al 5052-H32 alloy weldments. Design/methodology/approach Aluminum 5052 H32 specimens are welded at different combinations of vibromotor voltage inputs and time of vibrations. Voltage input is varied from 50 to 230 V at an interval of 10 V. At each voltage input to the vibromotor, there are three levels of time of vibration, i.e. 80, 90 and 100 s. The vibratory TIG-welded specimens are tested for their mechanical and microstructural properties. Findings The results indicate that the mechanical properties of aluminum alloy weld connections improved by increasing voltage input up to 160 V. Also, it has been observed that by increasing vibromotor voltage input beyond 160 V, mechanical properties were reduced significantly. It is also found that vibration time has less influence on the mechanical properties of weld connections. Improvement in hardness and ultimate tensile strength of vibratory welded joints is 16 and 14%, respectively, when compared without vibration, i.e. normal weld conditions. Average grain size is measured as per ASTM E 112–96. Average grain size is in the case of 0, 120, 160 and 230 is 20.709, 17.99, 16.57 and 20.8086 µm, respectively. Originality/value Novel vibratory TIG welded joints are prepared. Mechanical and micro-structural properties are tested.

scholarly journals Effects of Substitution of Y with Yb and Ce on the Microstructures and Mechanical Properties of Mg88.5Zn5Y6.5

Metals ◽  
2020 ◽  
Vol 11 (1) ◽  
pp. 31
Author(s):  
Hongxin Liao ◽  
Taekyung Lee ◽  
Jiangfeng Song ◽  
Jonghyun Kim ◽  
Fusheng Pan
Keyword(s):  
Mechanical Properties ◽  
Thermal Stability ◽  
Tensile Strength ◽  
Ultimate Tensile Strength ◽  
Yield Strength ◽  
Creep Resistance ◽  
Room Temperature ◽  
High Thermal Stability ◽  
Long Period ◽  
Microstructures And Mechanical Properties

The microstructures and mechanical properties of the Mg88.5Zn5Y6.5-XREX (RE = Yb and Ce, X = 0, 1.5, 3.0, and 4.5) (wt.%) alloys were investigated in the present study. Mg88.5Zn5Y6.5 is composed of three phases, namely, α-Mg, long-period stacking ordered (LPSO) phases, and intermetallic compounds. The content of the LPSO phases decreased with the addition of Ce and Yb, and no LPSO phases were detected in Mg88.5Zn5Y2.0Yb4.5. The alloys containing the LPSO phases possessed a stratified microstructure and exhibited excellent mechanical properties. Mg88.5Zn5Y5.0Ce1.5 exhibited the highest creep resistance and mechanical strength at both room temperature and 200 °C, owing to its suitable microstructure and high thermal stability. The yield strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature was 358 MPa. The ultimate tensile strength of Mg88.5Zn5Y5.0Ce1.5 at room temperature and 200 °C was 453 MPa and 360 MPa, respectively.

scholarly journals Microstructure and Mechanical Properties of Dissimilar Friction Welding Ti-6Al-4V Alloy to Nitinol

Metals ◽  
2021 ◽  
Vol 11 (1) ◽  
pp. 109
Author(s):  
Ateekh Ur Rehman ◽  
Nagumothu Kishore Babu ◽  
Mahesh Kumar Talari ◽  
Yusuf Siraj Usmani ◽  
Hisham Al-Khalefah
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Flow Stress ◽  
Intermetallic Compound ◽  
Ultimate Tensile Strength ◽  
Friction Welding ◽  
Welding Process ◽  
Weld Interface ◽  
Dissimilar Joints ◽  
Dissimilar Alloys

In the present study, a friction welding process was adopted to join dissimilar alloys of Ti-Al-4V to Nitinol. The effect of friction welding on the evolution of welded macro and microstructures and their hardnesses and tensile properties were studied and discussed in detail. The macrostructure of Ti-6Al-4V and Nitinol dissimilar joints revealed flash formation on the Ti-6Al-4V side due to a reduction in flow stress at high temperatures during friction welding. The optical microstructures revealed fine grains near the Ti-6Al-4V interface due to dynamic recrystallization and strain hardening effects. In contrast, the area nearer to the nitinol interface did not show any grain refinement. This study reveals that the formation of an intermetallic compound (Ti2Ni) at the weld interface resulted in poor ultimate tensile strength (UTS) and elongation values. All tensile specimens failed at the weld interface due to the formation of intermetallic compounds.

Sign in / Sign up

Export Citation Format

Share Document