scholarly journals Energy Yield of Tracking PV Systems in Jordan

2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
A. Al Tarabsheh ◽  
I. Etier ◽  
A. Nimrat
Keyword(s):  
Tracking System ◽  
Global Radiation ◽  
System Optimization ◽  
Energy Yield ◽  
Pv System ◽  
Pv Systems ◽  
Pv Modules ◽  
Inclination Angles ◽  
Simulation Results ◽  
The One

This paper analyzes the energy yield of photovoltaic (PV) modules mounted on fixed tilt, one-axis, and two-axis tracking system towards maximizing the annual energy production. The performance evaluation of the proposed design of the tracking systems is carried via simulating the global radiation averages using METEONORM software and depicting the simulation results in figures using MATLAB software. The one-axis system is simulated by either fixing the azimuth angle while optimizing the inclination angles or fixing the inclination angle while optimizing the azimuth angles; simulation results show an increase in energy yield of 5.87% and 20.12% compared to that of fixed tilt system, respectively. In the two-axis system, optimization of both azimuth and inclination angles is carried out simultaneously which resulted in 30.82% improvement in energy yield. Therefore, 30% improvement in energy yield is directly reflected as saving in PV system cost due to reduction of the PV modules surface area.

scholarly journals Comparative Analysis of Ground-Mounted vs. Rooftop Photovoltaic Systems Optimized for Interrow Distance between Parallel Arrays

Energies ◽  
2020 ◽  
Vol 13 (14) ◽  
pp. 3639
Author(s):  
Ahmed Bilal Awan ◽  
Mohammed Alghassab ◽  
Muhammad Zubair ◽  
Abdul Rauf Bhatti ◽  
Muhammad Uzair ◽  
...  
Keyword(s):  
Performance Comparison ◽  
Performance Ratio ◽  
Energy Output ◽  
Energy Yield ◽  
Pv System ◽  
Utilization Factor ◽  
Pv Systems ◽  
Pv Modules ◽  
Mutual Shading ◽  
Land Cost

The aim of this research is to perform an in-depth performance comparison of ground-mounted and rooftop photovoltaic (PV) systems. The PV modules are tilted to receive maximum solar irradiance. The efficiency of the PV system decreases due to the mutual shading impact of parallel tilted PV modules. The mutual shading decreases with the increasing interrow distance of parallel PV modules, but a distance that is too large causes an increase in land cost in the case of ground-mounted configuration and a decrease in roof surface shading in the case of rooftop configuration, because larger sections of roof are exposed to sun radiation. Therefore, an optimized interrow distance for the two PV configurations is determined with the aim being to minimize the levelized cost of energy (LCoE) and maximize the energy yield. The model of the building is simulated in EnergyPlus software to determine the cooling load requirement and roof surface temperatures under different shading scenarios. The layout of the rooftop PV system is designed in Helioscope software. A detailed comparison of the two systems is carried out based on energy output, performance ratio, capacity utilization factor (CUF), energy yield, and LCoE. Compared to ground-mounted configuration, the rooftop PV configuration results in a 2.9% increase in CUF, and up to a 23.7% decrease in LCoE. The results of this research show that installing a PV system on a roof has many distinct advantages over ground-mounted PV systems such as the shading of the roof, which leads to the curtailment of the cooling energy requirements of the buildings in hot regions and land cost savings, especially for urban environments.

scholarly journals Reconfigurable Distributed Power Electronics Technique for Solar PV Systems

Electronics ◽  
2021 ◽  
Vol 10 (9) ◽  
pp. 1121
Author(s):  
Kamran Ali Khan Niazi ◽  
Yongheng Yang ◽  
Tamas Kerekes ◽  
Dezso Sera
Keyword(s):  
Energy Yield ◽  
Solar Pv ◽  
Charge Redistribution ◽  
Pv System ◽  
Partial Shading ◽  
Pv Systems ◽  
Simulation Based ◽  
In Series ◽  
A Cell ◽  
Power Balancing

A reconfiguration technique using a switched-capacitor (SC)-based voltage equalizer differential power processing (DPP) concept is proposed in this paper for photovoltaic (PV) systems at a cell/subpanel/panel-level. The proposed active diffusion charge redistribution (ADCR) architecture increases the energy yield during mismatch and adds a voltage boosting capability to the PV system under no mismatch by connected the available PV cells/panels in series. The technique performs a reconfiguration by measuring the PV cell/panel voltages and their irradiances. The power balancing is achieved by charge redistribution through SC under mismatch conditions, e.g., partial shading. Moreover, PV cells/panels remain in series under no mismatch. Overall, this paper analyzes, simulates, and evaluates the effectiveness of the proposed DPP architecture through a simulation-based model prepared in PSIM. Additionally, the effectiveness is also demonstrated by comparing it with existing conventional DPP and traditional bypass diode architecture.

scholarly journals A Simple Mismatch Mitigating Partial Power Processing Converter for Solar PV Modules

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2308
Author(s):  
Kamran Ali Khan Niazi ◽  
Yongheng Yang ◽  
Tamas Kerekes ◽  
Dezso Sera
Keyword(s):  
Experimental Tests ◽  
Energy Yield ◽  
Power Electronic ◽  
Solar Pv ◽  
Partial Shading ◽  
Loss Analysis ◽  
Pv Systems ◽  
Pv Module ◽  
Pv Modules ◽  
In Series

Partial shading affects the energy harvested from photovoltaic (PV) modules, leading to a mismatch in PV systems and causing energy losses. For this purpose, differential power processing (DPP) converters are the emerging power electronic-based topologies used to address the mismatch issues. Normally, PV modules are connected in series and DPP converters are used to extract the power from these PV modules by only processing the fraction of power called mismatched power. In this work, a switched-capacitor-inductor (SCL)-based DPP converter is presented, which mitigates the non-ideal conditions in solar PV systems. A proposed SCL-based DPP technique utilizes a simple control strategy to extract the maximum power from the partially shaded PV modules by only processing a fraction of the power. Furthermore, an operational principle and loss analysis for the proposed converter is presented. The proposed topology is examined and compared with the traditional bypass diode technique through simulations and experimental tests. The efficiency of the proposed DPP is validated by the experiment and simulation. The results demonstrate the performance in terms of higher energy yield without bypassing the low-producing PV module by using a simple control. The results indicate that achieved efficiency is higher than 98% under severe mismatch (higher than 50%).

scholarly journals Estimation of Solar Irradiation on Inclined Surface Based on Web Databases

2014 ◽  
Vol 60 (4) ◽  
pp. 315-320 ◽  
Author(s):  
Gustaw Mazurek
Keyword(s):  
Solar Irradiation ◽  
Pv System ◽  
Solar Systems ◽  
Pv Systems ◽  
Pv Modules ◽  
Tilted Plane ◽  
Annual Scale ◽  
Inclined Surface ◽  
Long Operation ◽  
Good Agreement

Abstract Estimation of Global Tilted Irradiation (GTI) is a key to performance assessment of typical solar systems since they usually employ tilted photovoltaic (PV) modules or collectors. Numerous solar radiation databases can deliver irradiation values both on horizontal and tilted plane, however they are validated mostly with horizontal-plane ground measurements. In this paper we have compared GTI estimates retrieved from five Internet databases with results of measurements at two PV systems located in Poland. Our work shows that in spite of good agreement in annual scale, there is a tendency to underestimate GTI in summer and overestimate in winter, when PV modules can receive less than a half of expected irradiation. The latter issue affects sizing of PV system components and implies a correction needed to achieve all-year long operation.

scholarly journals A Novel Transformer-less Grid Tie Inverter for Rooftop PV system

2017 ◽  
Vol 16 (1) ◽  
pp. 37-46
Author(s):  
Mahir Mahdee ◽  
Chowdhury Mohammad Samir ◽  
Sunzidur Rahman ◽  
Md. Shabuj Hossain ◽  
Ahmed Mortuza Saleque ◽  
...  
Keyword(s):  
Multilevel Inverter ◽  
Pv System ◽  
Constant Input ◽  
Pv Systems ◽  
Design And Implementation ◽  
Pv Array ◽  
Arduino Microcontroller ◽  
Photo Voltaic ◽  
Simulation Results ◽  
Inverter Topology

This paper presents a relatively new concept for the design and implementation of a grid-tie inverter for photo voltaic (PV) systems. The proposed method will eliminate the uses of battery pack hence overall cost of any PV project will be significantly reduced. As the output of any PV array varies with the variation of solar irradiance hence a boost converter with PID regulated variable duty cycle has been used to keep a constant input to the inverter. Multilevel inverter topology has been proposed for utility grid connectivity. The proposed design is simulated in MATLAB/Simulink and a prototype is also implemented to verify the simulation results. The controllers are implemented in Arduino microcontroller board.

scholarly journals Evaluation of Contribution of PV Array and Inverter Configurations to Rooftop PV System Energy Yield Using Machine Learning Techniques

Energies ◽  
2019 ◽  
Vol 12 (16) ◽  
pp. 3158 ◽  
Author(s):  
Ngoc Thien Le ◽  
Watit Benjapolakul
Keyword(s):  
Machine Learning ◽  
Investment Decision ◽  
High Volume ◽  
Machine Learning Techniques ◽  
Energy Yield ◽  
Pv System ◽  
Useful Knowledge ◽  
Pv Systems ◽  
Learning Techniques ◽  
The Difference

Rooftop photovoltaics (PV) systems are attracting residential customers due to their renewable energy contribution to houses and to green cities. However, customers also need a comprehensive understanding of system design configuration and the related energy return from the system in order to support their PV investment. In this study, the rooftop PV systems from many high-volume installed PV systems countries and regions were collected to evaluate the lifetime energy yield of these systems based on machine learning techniques. Then, we obtained an association between the lifetime energy yield and technical configuration details of PV such as rated solar panel power, number of panels, rated inverter power, and number of inverters. Our findings reveal that the variability of PV lifetime energy is partly explained by the difference in PV system configuration. Indeed, our machine learning model can explain approximately 31 % ( 95 % confidence interval: 29–38%) of the variant energy efficiency of the PV system, given the configuration and components of the PV system. Our study has contributed useful knowledge to support the planning and design of a rooftop PV system such as PV financial modeling and PV investment decision.

Assessment of the Energy Gain of Photovoltaic Systems by Using Solar Tracking in Equatorial Regions

2018 ◽  
Vol 140 (3) ◽  
Author(s):  
Freddy Ordóñez ◽  
Carlos Morales ◽  
Jesús López-Villada ◽  
Santiago Vaca
Keyword(s):  
Tracking System ◽  
Solar Irradiation ◽  
Pv Systems ◽  
Pv Array ◽  
Solar Arrays ◽  
The North ◽  
Operation Conditions ◽  
Solar Tracking ◽  
The One ◽  
The Impact

Solar tracking is a major alternative to increase the electric output of a photovoltaic (PV) module, and therefore, improves the global energy collected by PV systems. Nonetheless, solar-tracking PV systems require more resources and energy than static systems. Additionally, the presence of cloudiness and shadows from near buildings may reduce the profitability of these systems. Therefore, their feasibility must be assessed in order to justify their application. In equatorial latitudes, the sun's movement through the sky is in the zenith East–West axis. It may be advantageous, since the best tilt in such latitudes is the horizontal. In these terms, the main objective of this research is to numerically assess the performance of a PV array with solar tracking and under typical operation conditions in equatorial latitudes. For this, the assessment of the solar resource in Quito was analyzed in first place. Then, the comparison between three solar arrays was studied to evaluate the feasibility of solar tracking (two-axes tracking, horizontal one-axis tracking, and horizontal fixed). Additionally, the impact of cloudiness and shadows in the system was analyzed. The results showed that the horizontal one-axis tracking is the most beneficial option for equatorial latitudes as the two-axes tracking system only surpasses the gains of the one-axis tracking marginally. Furthermore, the use of a strategy to place the PV modules horizontally in cloudy conditions seems to be marginally advantageous. Finally, the shadows created from neighboring buildings in the East and West of the system may reduce considerably the solar irradiation on the PV-array (not the ones in the north and south).

scholarly journals A Novel Current Sensor less MPPT based Approach for PV Applications Using PSO Technique

2021 ◽  
Vol 2070 (1) ◽  
pp. 012123
Author(s):  
Vinay Kumar ◽  
T Naveen Kumar ◽  
K T Prajwal
Keyword(s):  
Solar Energy ◽  
Renewable Energy Sources ◽  
Maximum Power ◽  
Current Sensor ◽  
Pv System ◽  
Pv Systems ◽  
Power Resources ◽  
Point Tracking ◽  
Power Point ◽  
The One

Abstract As an increased demand in power resources and to reduce global warming, Renewable Energy Sources (RES) are preferred over the conventional sources. Among various available RES, solar energy is the effective and efficient one. The solar energy is also clean and free energy. The use of Maximum Power Point Tracking (MPPT) is the one of the techniques to get maximized output power from the Photo Voltaic (PV) system. The proposed method uses a voltage sensor by eliminating the need of current sensor based on selected technique using Partial Swarm Optimization (PSO) technique interfaced with DC-DC boost converter. PSO technique is one of the methods which has high conflux speed, to precisely track the maximum power. The result of the planned methodology is studied with the assistance of an acceptable simulation applied in MATLAB/Simulink setting for experiment to valid of microcontroller which is employed. The result obtained from the simulations studies showed that current sensor less methodology using PSO technique can extract the maximize power from PV systems.

Performance of Bi-Facial PV Modules in Urban Settlements in Tropical Regions

2013 ◽  
Vol 853 ◽  
pp. 312-316
Author(s):  
Carlo Pisigan ◽  
Fan Jiang
Keyword(s):  
Urban Areas ◽  
Weather Conditions ◽  
Energy Output ◽  
Rear Side ◽  
Energy Yield ◽  
Tropical Regions ◽  
Pv Systems ◽  
Irradiation Energy ◽  
Pv Modules ◽  
Urban Settlements

This paper studies the performance of bifacial Heterojunction with Intrinsic Thin-layer (HIT) PV modules through a one-year experiment in Singapore. Two 1.2kWp (front side)/0.84kWp (rear side) PV systems were installed vertically, facing the N-S and E-W directions respectively. The operational data of two systems were monitored and collected to analyze their performance under different weather conditions. This paper will presentthe change of irradiation, energy yield and the AC energy output of the bifacial PV systems. The results help to understand the impacts of system installation on the energy yield of vertically-installedbifacial HIT PV systems, to find out its advantages in applications over monofacial PV modules and to explore the potential of bifacial PV modules in tropical regions, especially in urban areas like Singapore.

Simulation of a Mechatronic Dual-Axis Tracking System for PV Panels

2016 ◽  
Vol 859 ◽  
pp. 81-87
Author(s):  
Cătălin Alexandru
Keyword(s):  
Dynamic Simulation ◽  
Tracking System ◽  
Virtual Prototyping ◽  
Point Of View ◽  
Energetic Efficiency ◽  
Mechanical Device ◽  
Pv System ◽  
Pv Systems ◽  
Pv Panel ◽  
Main Components

The paper shows the dynamic simulation in virtual environment of a dual-axis sun tracking mechanism with application in photovoltaic (PV) systems, with the aim to increase the energetic efficiency. The idea is to design a tracking mechanism that automatically changes the diurnal and elevation (altitudinal) position of the PV panel, by considering a predefined tracking algorithm, for maximizing the degree of use of the solar energy (i.e. the incident solar radiation). The tracking mechanism is approached in mechatronic concept, by through the implementation of the two main components (mechanical device, and actuating & control system) at the virtual prototype level. The dynamic simulation was performed by using a virtual prototyping platform, which includes the following software solutions: CATIA, ADAMS/View & ADAMS/Controls, and EASY5. The behavior (performance) of the tracking mechanism is evaluated from energetic efficiency point of view, considering the energy gain reported to an equivalent fixed PV system.

Sign in / Sign up

Export Citation Format

Share Document