scholarly journals Biocompatibility of Nanoporous TiO2Coating on NiTi Alloy Prepared via Dealloying Method

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Jin Huang ◽  
Junqiang Wang ◽  
Xiangdong Su ◽  
Weichang Hao ◽  
Tianmin Wang ◽  
...  
Keyword(s):  
Low Temperature ◽  
Shape Memory ◽  
Biomedical Application ◽  
Niti Alloy ◽  
Treatment Method ◽  
Niti Shape Memory Alloy ◽  
Contact Method ◽  
Biological Compatibility ◽  
Before And After ◽  
Niti Shape Memory Alloys

This paper investigated the biocompatibility of nanoporous TiO2coating on NiTi shape-memory alloy (SMA) prepared via dealloying method. Our previous study shows that the dealloying treatment at low temperature leads to 130 nm Ni-free surface titania surface layer, which possesses good bioactivity because of the combination of hydroxyl (OH−) group in the process of dealloying treatment simultaneously. In this paper, the biological compatibility of NiTi alloy before and after dealloying treatment was evaluated and compared by direct contact method with dermal mesenchymal stem cells (DMSCs) by the isolated culture way. The interrelation between the biological compatibility and surface change of material after modification was systematically analyzed. As a consequence, the dealloying treatment method at low temperature could be of interest for biomedical application, as it can avoid sensitization and allergies and improve biocompatibility of NiTi shape-memory alloys. Thus it laid the foundation of the clinical trials for surface modification of NiTi memory alloy.

scholarly journals Experimental Analysis of NiTi Alloy during Strain-Controlled Low-Cycle Fatigue

Materials ◽  
2021 ◽  
Vol 14 (16) ◽  
pp. 4455
Author(s):  
Pedro Cunha Lima ◽  
Patrícia Freitas Rodrigues ◽  
Ana Sofia Ramos ◽  
José D. M. da Costa ◽  
Francisco Manuel Braz Fernandes ◽  
...  
Keyword(s):  
Shape Memory Alloy ◽  
Shape Memory ◽  
Low Cycle Fatigue ◽  
Niti Alloy ◽  
Niti Shape Memory Alloy ◽  
Cycle Fatigue ◽  
Maximum Deformation ◽  
Transmission Electron ◽  
Before And After

The interaction between the stress-induced martensitic transformation and resistivity behavior of superelastic NiTi shape memory alloy (SMA) was studied. Strain-controlled low-cycle fatigue up to 6% was monitored by in situ electrical resistivity measurements. The experimental results show that a great motion of martensite fronts results in a significant accumulation of defects, as evidenced by transmission electron microscopy (TEM), before and after the tensile cycles. This gives rise to an overall increase of the resistivity values up to the maximum deformation. Therefore, the research suggests that shape memory alloy wire has great potential as a stress sensor inside bulk materials.

scholarly journals Functionalization of the NiTi Shape Memory Alloy Surface by HAp/SiO2/Ag Hybrid Coatings Formed on SiO2-TiO2 Glass Interlayer

Materials ◽  
2020 ◽  
Vol 13 (7) ◽  
pp. 1648 ◽  
Author(s):  
Karolina Dudek ◽  
Mateusz Dulski ◽  
Bożena Łosiewicz
Keyword(s):  
Heat Treatment ◽  
Shape Memory ◽  
Electrochemical Impedance ◽  
Niti Alloy ◽  
Composite Coatings ◽  
Energy Dispersive Spectrometer ◽  
Weight Ratio ◽  
Hybrid Coatings ◽  
Niti Shape Memory Alloy ◽  
Niti Shape Memory Alloys

The surface modification of NiTi shape memory alloys is a method for increasing their multi-functionalities. In our solution, hydroxyapatite powder was mixed with a chemically synthesized silicon dioxide/silver (nSiO2/Ag) nanocomposite in a different weight ratio between components (1:1, 5:1, and 10:1) and then electrophoretically deposited on the surface of the NiTi alloy, under various time and voltage conditions. Subsequently, uniform layers were subjected to heat treatment at 700 °C for 2 h in an argon atmosphere to improve the strength of their adhesion to the NiTi substrate. A change in linear dimensions of the co-deposited materials during the sintering process was also analyzed. After the heat treatment, XRD, Raman, and Scanning Electron Microscopy (SEM) + Energy Dispersive Spectrometer (EDS) studies revealed the formation of completely new composite coatings, which consisted of rutile and TiO2-SiO2 glass with silver oxide and HAp particles that were embedded into such coatings. It was found that spalling characterized the 1:1 ratio coating, while the others were crack-free, well-adhered, and capable of deformation to 3.5%. Coatings with a higher concentration of nanocomposite were rougher. Electrochemical impedance spectroscopy (EIS) tests in Ringer’s solution revealed the capacitive behavior of the material with high corrosion resistance. The kinetics and susceptibility to pitting corrosion was the highest for the NiTi electrode that was coated with a 5:1 ratio HAp/nSiO2/Ag hybrid coating.

A Study on Grinding Performance of Porous NiTi Shape Memory Alloy

2007 ◽  
Vol 359-360 ◽  
pp. 143-147
Author(s):  
Yi Yi Tao ◽  
Jiu Hua Xu ◽  
Wen Feng Ding
Keyword(s):  
Shape Memory ◽  
Mechanical Performance ◽  
Niti Alloy ◽  
Surface Characteristics ◽  
Niti Shape Memory Alloy ◽  
Machining Performance ◽  
Experimental Conditions ◽  
Porous Niti ◽  
Force Ratio ◽  
Niti Shape Memory Alloys

The machining performance of porous NiTi shape memory alloys prepared using powder metallurgical production technique has been investigated experimentally in the grinding operation. Grinding force ratio, specific grinding energy, surface characteristics were detected. The result reveals that, much difference of grinding characteristics exists among three kinds of NiTi alloy because of the pore rate and the mechanical performance induced by TiH2. Under the experimental conditions, the integrated effects of predominant plastic flow and slight brittle fracture were taken for porous NiTi alloy during grinding. Additionally, the grinding parameters should be chosen carefully, otherwise the surface quality deteriorates and even the microcrack perhaps appears.

The Effect of Chemical Composition on Microstructure and Transformation Behavior of NiTi Shape Memory Alloy Prepared by Vacuum Arc Melting

2008 ◽  
Vol 1 ◽  
pp. 91-97
Author(s):  
Mandana Bornapour ◽  
Y. Motemanni ◽  
Mahmoud Nili-Ahmadabadi ◽  
S. Raygan
Keyword(s):  
Phase Transformation ◽  
Shape Memory Alloys ◽  
Shape Memory ◽  
Niti Alloy ◽  
Martensite Phase ◽  
Vacuum Arc ◽  
Niti Shape Memory Alloy ◽  
Arc Melting ◽  
Vacuum Arc Melting ◽  
Niti Shape Memory Alloys

NiTi shape memory alloys are a group of materials which have a lot of applications especially in aerospace industries and medical equipments because of their excellent properties. Shape memory effect (SME), pseudo-elasticity (PE), high corrosion resistance and biocompatibility is special properties of these alloys which lead to their extensive applications. The superior behavior of NiTi alloy is due to thermoelastic martensitic phase transformation. In the present paper, two NiTi shape memory alloys were prepared by non-consumable vacuum arc melting technique in copper water cooled crucible. One of them had commercial elements and the other had high purity elements. Metallographic investigation, chemical analysis, XRD and DSC were carried out on two alloys. Metallographic observation and XRD shows that structure at ambient temperature consists of austenite phase besides Ti2Ni, Ni3Ti intermetallic compounds and martensite phase. Transformation investigation determines that the impurity such as iron in commercial alloy causes two stage phase transformation B2→R→B19′.

scholarly journals Net-Shape NiTi Shape Memory Alloy by Spark Plasma Sintering Method

2021 ◽  
Vol 11 (4) ◽  
pp. 1802
Author(s):  
Sneha Samal ◽  
Orsolya Molnárová ◽  
Filip Průša ◽  
Jaromír Kopeček ◽  
Luděk Heller ◽  
...  
Keyword(s):  
Shape Memory ◽  
Shape Memory Effect ◽  
Spark Plasma Sintering ◽  
Memory Effect ◽  
Niti Alloy ◽  
Niti Shape Memory Alloy ◽  
Good Shape ◽  
Plasma Sintering ◽  
Shape Memory Effects ◽  
Spark Plasma

An analysis of the shape memory effect of a NiTi alloy by using the spark plasma sintering approach has been carried out. Spark plasma sintering of Ti50Ni50 powder (20–63 µm) at a temperature of 900 °C produced specimens showing good shape memory effects. However, the sample showed 2.5% porosity due to a load of 48 MPa. Furthermore, an apparent shape memory effect was recorded and the specimens were characterized by uniformity in chemical composition and shape memory alloys of NiTi showed significant austenite phases with a bending strain recovery of >2.5%.

scholarly journals Key Properties of a Bioactive Ag-SiO2/TiO2 Coating on NiTi Shape Memory Alloy as Necessary at the Development of a New Class of Biomedical Materials

2021 ◽  
Vol 22 (2) ◽  
pp. 507
Author(s):  
Mateusz Dulski ◽  
Robert Gawecki ◽  
Sławomir Sułowicz ◽  
Michal Cichomski ◽  
Alicja Kazek-Kęsik ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Dermal Fibroblast ◽  
Niti Alloy ◽  
Bacterial Biofilm ◽  
Niti Shape Memory Alloy ◽  
Normal Human Dermal Fibroblast ◽  
Water Contact ◽  
Nano Coating

Recent years have seen the dynamic development of methods for functionalizing the surface of implants using biomaterials that can mimic the physical and mechanical nature of native tissue, prevent the formation of bacterial biofilm, promote osteoconduction, and have the ability to sustain cell proliferation. One of the concepts for achieving this goal, which is presented in this work, is to functionalize the surface of NiTi shape memory alloy by an atypical glass-like nanocomposite that consists of SiO2-TiO2 with silver nanoparticles. However, determining the potential medical uses of bio(nano)coating prepared in this way requires an analysis of its surface roughness, tribology, or wettability, especially in the context of the commonly used reference coat-forming hydroxyapatite (HAp). According to our results, the surface roughness ranged between (112 ± 3) nm (Ag-SiO2)—(141 ± 5) nm (HAp), the water contact angle was in the range (74.8 ± 1.6)° (Ag-SiO2)—(70.6 ± 1.2)° (HAp), while the surface free energy was in the range of 45.4 mJ/m2 (Ag-SiO2)—46.8 mJ/m2 (HAp). The adhesive force and friction coefficient were determined to be 1.04 (Ag-SiO2)—1.14 (HAp) and 0.247 ± 0.012 (Ag-SiO2) and 0.397 ± 0.034 (HAp), respectively. The chemical data showed that the release of the metal, mainly Ni from the covered NiTi substrate or Ag from Ag-SiO2 coating had a negligible effect. It was revealed that the NiTi alloy that was coated with Ag-SiO2 did not favor the formation of E. coli or S. aureus biofilm compared to the HAp-coated alloy. Moreover, both approaches to surface functionalization indicated good viability of the normal human dermal fibroblast and osteoblast cells and confirmed the high osteoconductive features of the biomaterial. The similarities of both types of coat-forming materials indicate an excellent potential of the silver-silica composite as a new material for the functionalization of the surface of a biomaterial and the development of a new type of functionalized implants.

EFFECTS OF PARTICLE SIZE AND SINTERING TEMPERATURE ON SUPERELASTICITY BEHAVIOR OF NiTi SHAPE MEMORY ALLOY USING NANOINDENTATION

2021 ◽  
pp. 2150024
Author(s):  
C. VELMURUGAN ◽  
V. SENTHILKUMAR
Keyword(s):  
Particle Size ◽  
Shape Memory Alloy ◽  
Shape Memory ◽  
Sintering Temperature ◽  
Niti Alloy ◽  
Indentation Load ◽  
Niti Shape Memory Alloy ◽  
Recovery Ratio ◽  
Work Recovery ◽  
Niti Sma

The present study investigates the superelasticity properties of spark plasma sintered (SPS) nickel titanium shape memory alloy (NiTi SMA) with the influence of sintering temperature and particle size. The nanoindentation is conducted on the surface of the NiTi SMA at various loads such as 100, 300 and 500[Formula: see text]mN. The nanoindentation technique determines the quantitative results of elasto-plastic properties such as depth recovery in the form of superelasticity, stiffness, hardness and work recovery ratio from load–depth ([Formula: see text]–[Formula: see text]) data during loading and unloading of the indenter. Experimental findings show that the depth and work recovery ratio increases with the decrease of indentation load and particle size. In contrast, increasing the sintering temperature exhibited a better depth and work recovery due to the removal of pores which could enhance the reverse transformation. The contact stiffness is influenced by [Formula: see text] which leads to attain a maximum stiffness at the highest load (500[Formula: see text]mN) and particle size (45[Formula: see text][Formula: see text]m) along with the lowest sintering temperature (700∘C). NiTi alloy exhibited a maximum hardness of 9.46[Formula: see text]GPa when subjected to indent at the lowest load and particle size sintered at 800∘C. The present study reveals a better superelastic behavior in NiTi SMA by reducing the particle size and indentation load associated with the enhancement of sintering temperature.

SHAPE MEMORY INVESTIGATION OF SMART CAMAR LOGO USING NITI ALLOY WIRE

2015 ◽  
Vol 76 (3) ◽  
Author(s):  
Muhammad Safwan Shuhaimi ◽  
Nubailah Abd. Hamid ◽  
Rosliza Razali ◽  
Muhammad Hussain Ismail
Keyword(s):  
Phase Transformation ◽  
Shape Memory ◽  
Shape Memory Effect ◽  
Memory Effect ◽  
Niti Alloy ◽  
Niti Shape Memory Alloy ◽  
Shape Effect ◽  
Niti Wire ◽  
The Wire ◽  
Reversible Phase

This project is investigates of NiTi shape memory alloy for simple smart application. The shape memory effect (SME) is attributed from the reversible phase transformation when subjected to stress and temperature. In this study, a small model of CAMAR logo was designed to mimic the shape memory effect. Three samples of wire were investigated; (i) Austenitic NiTi (ii) Martensitic NiTi and (iii) commercial plain carbon steel. The reversible austenite to martensite transformation of the NiTi wire was investigated by a differential scanning calorimetry (DSC) at temperatures ranging from -50 and 200oC. The wire was shaped into CAMAR logo using a mould and then heated at 500°C for 30 minutes in a high temperature furnace. To observe the shape effect recovery, the wire was straighten and reheated in warm water at different temperatures. Results showed that the austenitic wire exhibited complete shape memory recovery after heated at temperature approximately 35°C and  80°C. For the martensitic wire, complete recovery was only observed when the water temperature was ~ 80°C and no recovery was observed at ~30°C. This recovery effect was significantly influenced by the reversible phase transformation temperatures (PTTs) which attributed from the Austenite finish (Af) temperature.

Sign in / Sign up

Export Citation Format

Share Document