scholarly journals Effect of Tetramethylammonium Hydroxide on Nucleation, Surface Modification and Growth of Magnetic Nanoparticles

2012 ◽  
Vol 2012 ◽  
pp. 1-10 ◽  
Author(s):  
Ângela L. Andrade ◽  
José D. Fabris ◽  
José D. Ardisson ◽  
Manuel A. Valente ◽  
José M. F. Ferreira
Keyword(s):  
Zeta Potential ◽  
Magnetite Nanoparticles ◽  
Heat Dissipation ◽  
Tetramethylammonium Hydroxide ◽  
Precipitation Method ◽  
Attenuated Total Reflectance ◽  
X Ray Diffraction ◽  
Experimental Conditions ◽  
Transmission Electron ◽  
Magnetite Particles

Nanoparticles of magnetite (Fe3O4) were obtained by reacting ferric chloride with sodium sulphite, through the reduction-precipitation method. The effects of adding tetramethylammonium hydroxide (TMAOH) during or after the precipitation of the iron oxide were studied in an attempt to obtain well-dispersed magnetite nanoparticles. Accordingly, the following experimental conditions were tested: (i) precipitation in absence of TMAOH (sample Mt), (ii) the same as (i) after peptizing with TMAOH (Mt1), (iii) TMAOH added to the reaction mixture during the precipitation of magnetite (Mt2). Analyses with transmission electron microscopy (TEM), X-ray diffraction, Mössbauer spectroscopy, attenuated total reflectance Fourier transform infrared spectroscopy (ATR-FTIR), zeta potential, and magnetization measurements up to 2.5 T revealed that magnetite was normally formed also in the medium containing TMAOH. The degree of particles agglomeration was monitored with laser diffraction and technique and inspection of TEM images. The relative contributions of Néel and Brownian relaxations on the magnetic heat dissipation were studied by investigating the ability of suspensions of these magnetite nanoparticles to release heat in aqueous and in hydrogel media. Based on ATR-FTIR and zeta potential data, it is suggested that the surfaces of the synthesized magnetite particles treated with TMAOH become coated with (CH3)4N+cations.

scholarly journals Transformation mechanism of magnetite nanoparticles

2015 ◽  
Vol 33 (2) ◽  
pp. 278-285 ◽  
Author(s):  
Umar Saeed Khan ◽  
Abdul Manan ◽  
Nasrullah Khan ◽  
Amir Mahmood ◽  
Abdur Rahim ◽  
...  
Keyword(s):  
Magnetite Nanoparticles ◽  
Bet Surface Area ◽  
X Ray Diffraction ◽  
Transformation Mechanism ◽  
X Ray ◽  
Transmission Electron ◽  
Different Temperatures ◽  
Magnetite Particles ◽  
Size And Morphology ◽  
Lower Temperature

AbstractA simple oxidation synthesis route was developed for producing magnetite nanoparticles with controlled size and morphology. Investigation of oxidation process of the produced magnetite nanoparticles (NP) was performed after synthesis under different temperatures. The phase transformation of synthetic magnetite nanoparticles into maghemite and, henceforth, to hematite nanoparticles at different temperatures under dry oxidation has been studied. The natural magnetite particles were directly transformed to hematite particles at comparatively lower temperature, thus, maghemite phase was bypassed. The phase structures, morphologies and particle sizes of the produced magnetic nanoparticles have been investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), energy dispersive X-ray spectrometry (EDX) and BET surface area analysis.

Preparation and Characterization of Magnetite Nanoparticles

2014 ◽  
Vol 618 ◽  
pp. 24-27 ◽  
Author(s):  
Fu Yan Zhao ◽  
Ya Ling Li ◽  
Lu Hai Li
Keyword(s):  
Surface Area ◽  
Magnetite Nanoparticles ◽  
High Performance ◽  
Catalytic Performance ◽  
Ammonium Bromide ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Particles Size Distribution ◽  
Magnetite Particles ◽  
Average Size

The preparation of magnetite nanoparticles with controlled size has attracted of scientific and technological broad attention. Spherical magnetite nanoparticles in the size range from 8nm to 22 nm were synthesized by coprecipiation method using hexadecyl trimethyl ammonium bromide (CTAB) as dispersant. Magnetite nanoparticles have good dispersibility and uniform particles size distribution. The properties were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), automated surface area and pore size analyzer, vibrating sample magnetometer (VSM) and the catalytic performance was measured using high performance liquid chromatography (HPLC). The saturation magnetization is 13.785emu/g, and the coercive force of the sample is 23.738G, the average size of the particles is 13.6 nm, specific surface area is 19.318 m2/g and phenol conversion is up to 99.5%. These results indicate the synthesized magnetite particles have good performance.

Magnetic and dielectric properties of BiFeO3 nanoparticles

2015 ◽  
Vol 7 (2) ◽  
pp. 1393-1403
Author(s):  
Dr R.P VIJAYALAKSHMI ◽  
N. Manjula ◽  
S. Ramu ◽  
Amaranatha Reddy
Keyword(s):  
Diffuse Reflectance Spectrum ◽  
Precipitation Method ◽  
Secondary Phases ◽  
X Ray Diffraction ◽  
Bifeo3 Nanoparticles ◽  
Transmission Electron ◽  
Multiferroic Bifeo3 ◽  
Pure Phase ◽  
Simple Chemical ◽  
Co Precipitation

Single crystalline nano-sized multiferroic BiFeO3 (BFO) powders were synthesized through simple chemical co-precipitation method using polyethylene glycol (PEG) as capping agent. We obtained pure phase BiFeO3 powder by controlling pHand calcination temperature. From X-ray diffraction studies the nanoparticles were unambiguously identified to have a rhombohedrally distorted perovskite structure belonging to the space group of R3c. No secondary phases were detected. It indicates single phase structure. EDX spectra indicated the appearance of three elements Bi, Fe, O in 1:1:3. From the UV-Vis diffuse reflectance spectrum, the absorption cut-off wavelength of the BFO sample is around 558nm corresponding to the energy band gap of 2.2 eV. The size (60-70 nm) and morphology of the nanoparticles have been analyzed using transmission electron microscopy (TEM).   Linear M−H behaviour and slight hysteresis at lower magnetic field is observed for BiFeO3 nanoparticles from Vibrating sample magnetometer studies. It indicates weak ferromagnetic behaviour at room temperature. From dielectric studies, the conductivity value is calculated from the relation s = L/RbA Sm-1 and it is around 7.2 x 10-9 S/m.

scholarly journals Enhanced Photocatalytic Activity of Cu2O Cabbage/RGO Nanocomposites under Visible Light Irradiation

Polymers ◽  
2021 ◽  
Vol 13 (11) ◽  
pp. 1712
Author(s):  
Appusamy Muthukrishnaraj ◽  
Salma Ahmed Al-Zahrani ◽  
Ahmed Al Otaibi ◽  
Semmedu Selvaraj Kalaivani ◽  
Ayyar Manikandan ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Thermo Gravimetric Analysis ◽  
Visible Region ◽  
Catalytic Performance ◽  
Precipitation Method ◽  
Gravimetric Analysis ◽  
X Ray Diffraction ◽  
X Ray ◽  
Dye Pollutants ◽  
Transmission Electron

Towards the utilization of Cu2O nanomaterial for the degradation of industrial dye pollutants such as methylene blue and methyl orange, the graphene-incorporated Cu2O nanocomposites (GCC) were developed via a precipitation method. Using Hummers method, the grapheme oxide (GO) was initially synthesized. The varying weight percentages (1–4 wt %) of GO was incorporated along with the precipitation of Cu2O catalyst. Various characterization techniques such as Fourier-transform infra-red (FT-IR), X-ray diffraction (XRD), UV–visible diffused reflectance (UV-DRS), Raman spectroscopy, thermo gravimetric analysis (TGA), energy-dispersive X-ray analysis (EDX), and electro chemical impedance (EIS) were followed for characterization. The cabbage-like morphology of the developed Cu2O and its composites were ascertained from field-emission scanning electron microscopy (FESEM) and high-resolution transmission electron microscopy (HR-TEM). In addition, the growth mechanism was also proposed. The results infer that 2 wt % GO-incorporated Cu2O composites shows the highest value of degradation efficiency (97.9% and 96.1%) for MB and MO at 160 and 220 min, respectively. Further, its catalytic performance over visible region (red shift) was also enhanced to an appreciable extent, when compared with that of other samples.

Microstructure Characterization of Metal Mixed Oxides

MRS Advances ◽  
2017 ◽  
Vol 2 (64) ◽  
pp. 4025-4030 ◽  
Author(s):  
T. Kryshtab ◽  
H. A. Calderon ◽  
A. Kryvko
Keyword(s):  
Mixed Oxides ◽  
Profile Analysis ◽  
Atomic Resolution ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Reconstruction Procedure ◽  
Transmission Electron ◽  
Xrd Patterns ◽  
Co Precipitation

ABSTRACTThe microstructure of Ni-Mg-Al mixed oxides obtained by thermal decomposition of hydrotalcite-like compounds synthesized by a co-precipitation method has been studied by using X-ray diffraction (XRD) and atomic resolution transmission electron microscopy (TEM). XRD patterns revealed the formation of NixMg1-xO (x=0÷1), α-Al2O3 and traces of MgAl2O4 and NiAl2O4 phases. The peaks profile analysis indicated a small grain size, microdeformations and partial overlapping of peaks due to phases with different, but similar interplanar spacings. The microdeformations point out the presence of dislocations and the peaks shift associated with the presence of excess vacancies. The use of atomic resolution TEM made it possible to identify the phases, directly observe dislocations and demonstrate the vacancies excess. Atomic resolution TEM is achieved by applying an Exit Wave Reconstruction procedure with 40 low dose images taken at different defocus. The current results suggest that vacancies of metals are predominant in MgO (NiO) crystals and that vacancies of Oxygen are predominant in Al2O3 crystals.

Template Induced Synthesis of Nano-Hydroxyapatite by Co-Precipitation Method

2011 ◽  
Vol 311-313 ◽  
pp. 1713-1716 ◽  
Author(s):  
Yan Rong Sun ◽  
Tao Fan ◽  
Chang An Wang ◽  
Li Guo Ma ◽  
Feng Liu
Keyword(s):  
Electron Microscope ◽  
Chondroitin Sulfate ◽  
Aspartic Acid ◽  
Transmission Electron Microscope ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structure And Morphology ◽  
Transmission Electron ◽  
Co Precipitation

Nano-hydroxyapatite with different morphology was synthesized by the co-precipitation method coupled with biomineralization using Ca(NO3)2•4H2O and (NH4)2HPO4 as reagents, adding chondroitin sulfate, agarose and aspartic acid as template. The structure and morphology of the prepared powders were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM).

Synthesis of Monodispersed Fe3O4 Magnetite Nanoparticles by Ethylene Glycol Solvothermal Method

2013 ◽  
Vol 634-638 ◽  
pp. 2276-2279 ◽  
Author(s):  
Gang Xu ◽  
Min Zhang ◽  
Ping Ou ◽  
Yi Zhang ◽  
Gao Rong Han
Keyword(s):  
Ethylene Glycol ◽  
Magnetite Nanoparticles ◽  
Solvothermal Method ◽  
Physical Property Measurement System ◽  
Physical Property ◽  
X Ray Diffraction ◽  
Ferromagnetic Property ◽  
Selected Area Electron Diffraction ◽  
Transmission Electron ◽  
Property Measurement

Monodispersed Fe3O4 magnetite nanoparticles were successfully synthesized via a simple solvothermal method, in which Fe(NO3)3•9H2O was used as the starting materials, KOH as the mineralizer, and ethylene glycol (en) as the solvent. X-ray diffraction (XRD) and selected area electron diffraction (SAED) were employed to characterize the phase composition, transmission electron microscope (TEM) to observe the morphology and the particle size, and physical property measurement system (PPMS) to investigate the magnetic property of the synthesized powders, respectively. The synthesized Fe3O4 magnetite nanoparticles are of 50-100nm in size, and of notable ferromagnetic property. The saturation magnetization, remanent magnetization, and coercive field are 68.8emu•g-1, 12.9emu•g-1, 138.5Oe, respectively. Based on the experimental resuts, the formation mechanism and the well monodispersed reason of the solvothersized Fe3O4 nanoparticles are discussed.

Monodisperse Fe3O4/Fe Core/Shell Nanoparticles with Enhanced Magnetic Property

2011 ◽  
Vol 306-307 ◽  
pp. 410-415
Author(s):  
Li Sun ◽  
Fu Tian Liu ◽  
Qi Hui Jiang ◽  
Xiu Xiu Chen ◽  
Ping Yang
Keyword(s):  
Average Diameter ◽  
Chemical Precipitation ◽  
Precipitation Method ◽  
Core Shell ◽  
X Ray Diffraction ◽  
Shell Nanoparticles ◽  
X Ray ◽  
Transmission Electron ◽  
Shell Particles ◽  
Core Shell Nanoparticles

Core/shell type nanoparticles with an average diameter of 20nm were synthesized by chemical precipitation method. Firstly, Monodisperse Fe3O4 nanoparticles were synthesized by solvethermal method. FeSO4ž7H2O and NaBH4 were respectively dissolved in distilled water, then moderated Fe3O4 particles and surfactant(PVP) were ultrasonic dispersed into the FeSO4ž7H2O solution. The resulting solution was stirred 2 h at room temperature. Fe could be deposited on the surface of monodispersed Fe3O4 nanoparticles to form core-shell particles. The particles were characterized by using various experimental techniques, such as transmission electron microscopy (TEM), X-ray diffraction (XRD), AGM and DTA. The results suggest that the saturation magnetization of the nanocomposites is 100 emu/g. The composition of the samples show monodisperse and the sides of the core/shell nanoparticles are 20-30nm. It is noted that the formation of Fe3O4/Fe nanocomposites magnetite nanoparticles possess superparamagnetic property.

scholarly journals Magnetic PbFe12O19-TiO2 nanocomposites and their photocatalytic performance in the removal of toxic pollutants

2018 ◽  
Vol 41 (3-4) ◽  
pp. 53-62 ◽  
Author(s):  
Behnaz Lahijani ◽  
Kambiz Hedayati ◽  
Mojtaba Goodarzi
Keyword(s):  
Electron Microscopy ◽  
Photocatalytic Performance ◽  
Sol Gel ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Gel Method ◽  
Sol Gel Method ◽  
Photocatalytic Effect ◽  
Transmission Electron ◽  
Ultraviolet Light Irradiation

Abstract In this work, the PbFe12O19 nanoparticles were prepared by the simple and optimized precipitation method with different organic surfactants and capping agents. In the next step, the TiO2 nanoparticles were synthesized using the sol-gel method. At the final step, the PbFe12O19-TiO2 nanocomposites were prepared via the sol-gel method. The effect of the precipitating agent on the morphology and particle size of the products was investigated. The prepared products were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and Fourier transform infrared spectroscopy. The results obtained by the vibrating sample magnetometer show the magnetic properties of the ferrite nanostructures. The photocatalytic effect of the PbFe12O19-TiO2 nanocomposite on the elimination of the azo dyes (acid black, acid violet and acid blue) under ultraviolet light irradiation was evaluated. The results indicate that the prepared nanocomposites have acceptable magnetic and photocatalytic performance.

scholarly journals Fabrication of a Food Nano-Platform Sensor for Determination of Vanillin in Food Samples

Sensors ◽  
2018 ◽  
Vol 18 (9) ◽  
pp. 2817 ◽  
Author(s):  
Vinod Gupta ◽  
Hassan Karimi-Maleh ◽  
Shilpi Agarwal ◽  
Fatemeh Karimi ◽  
Majede Bijad ◽  
...  
Keyword(s):  
High Sensitivity ◽  
Food Samples ◽  
Precipitation Method ◽  
Single Wall Carbon Nanotubes ◽  
Modified Carbon Paste Electrode ◽  
Carbon Paste ◽  
X Ray Diffraction ◽  
Transmission Electron ◽  
Paste Electrode

Herein, we describe the fabrication of NiO decorated single wall carbon nanotubes (NiO-SWCNTs) nanocomposites using the precipitation method. The synthesized NiO-SWCNTs nanocomposites were characterized by X-ray diffraction (XRD) and Transmission electron microscopy (TEM). Remarkably, NiO-SWCNTs and 1-butylpyridinium hexafluorophosphate modified carbon paste electrode (CPE/NiO-SWCNTs/BPrPF6) were employed for the electrochemical detection of vanillin. The vanillin sensor showed an ultra-high sensitivity of 0.3594 μA/μM and a low detection limit of 0.007 μM. In the final step, the NiO-SWCNTs/BPrPF6 was used as the suitable tool for food analysis.

Sign in / Sign up

Export Citation Format

Share Document