scholarly journals Parasitic-Element-Loaded UWB Antenna with Band-Stop Function for Mobile Handset Wireless USB

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Yohan Lim ◽  
Young Joong Yoon ◽  
Byungwoon Jung
Keyword(s):  
Impedance Bandwidth ◽  
Mobile Terminals ◽  
Uwb Antenna ◽  
Parasitic Element ◽  
Wireless Usb ◽  
Different Shapes ◽  
Mobile Handset

A UWB antenna loaded by parasitic elements for wireless USB of mobile handsets is proposed for UWB service in which a band-stop function of 5.725–5.825 GHz WLAN band is required. Two kinds of parasitic elements are incorporated into a rectangular radiator to obtain enhanced impedance bandwidth and band-stop function. The proposed antenna is very compact in size. Wide bandwidths of 3.15–4.75 GHz and 7.2–10.2 GHz are achieved while 5.725–5.825 GHz is notched. Three different shapes of conventional mobile terminals are also considered for measurement.

Design of wideband orthogonal MIMO antenna with improved correlation using a parasitic element for mobile handsets

2014 ◽  
Vol 8 (1) ◽  
pp. 109-115 ◽  
Author(s):  
Ali Akdagli ◽  
Abdurrahim Toktas
Keyword(s):  
Radiation Pattern ◽  
Common Ground ◽  
Ground Plane ◽  
Circuit Board ◽  
Impedance Bandwidth ◽  
Strip Line ◽  
Mobile Terminals ◽  
Parasitic Element ◽  
Mimo Antenna ◽  
Novel Design

In this paper, a novel design of compact wideband multiple-input multiple-output (MIMO) antenna operating over a frequency range of 1.8–4.0 GHz at 10 dB is presented for mobile terminals. The MIMO antenna design consists of two symmetrical and orthogonal radiating elements with a small size of 15.5 × 16.5 mm2 printed on the corners of a mobile circuit board. The radiating element is composed of four meandered monopole branches with a strip-line fed by a probe. By triangularly trimming the corners of the common ground plane beneath the radiating elements, not only the mutual coupling is reduced, but also impedance bandwidth is increased. Although, the antenna in this form has sufficient correlation level between the radiating elements for MIMO operation, a novel design of plus-shaped parasitic element is inserted to the ground plane between those radiating elements in order to further enhance the isolation. The performance of the MIMO antenna is investigated in terms of s-parameters, radiation pattern, gain, envelope correlation coefficient (ECC), and total active reflection coefficient (TARC), and is verified through the measurements. The results demonstrate that the proposed MIMO antenna has good characteristics of wideband, isolation, gain, radiation pattern, and is compatible with LTE, WiMAX, and WLAN, besides it is small, compact, and embeddable in mobile terminals.

scholarly journals Design of compact reconfigurable UWB antenna with WiMAX and WLAN band rejection

2020 ◽  
Vol 17 (3) ◽  
pp. 1427
Author(s):  
N. F. Miswadi ◽  
M. T. Ali
Keyword(s):  
Electromagnetic Interference ◽  
Antenna Design ◽  
Impedance Bandwidth ◽  
Uwb Antenna ◽  
Parasitic Element ◽  
Uwb Antennas ◽  
Operating Bandwidth ◽  
Good Agreement

Two reconfigurable UWB antennas with band rejection characteristics are presented in this paper. By applying concept of parasitic element and etching slot in these two proposed antenna design WiMAX and WLAN band rejection are obtained, respectively to avoid potential electromagnetic interference (EMI). The proposed antennas are printed on 30mm x 40 mm Rogers5880 substrate. Furthermore, ideal switches are employed to achieve switchable band rejection UWB antenna.In this paper, two designs of reconfigurable UWB antenna with band rejection were proposed; namely a reconfigurable UWB antenna with WiMAX band rejection (Antenna 1), reconfigurable UWB antenna with WLAN band rejection (Antenna 2). The proposed antennas were successfully simulated, fabricated and measured. The Antenna 1 have impedance bandwidth from 2.99 GHz to 10.58 GHz with band rejection at 3.52GHz by utilizing C-shaped parasitic stripline. Meanwhile, Antenna 2 achieved an operating bandwidth from 2.99 – 10.82GHz with VSWR less than 2 except for the WLAN band operating at 4.92 – 5.84 GHz.The measured results for both antennas show good agreement with simulated ones.

scholarly journals Compact and Low-Profile UWB Antenna Based on Graphene-Assembled Films for Wearable Applications

Sensors ◽  
2020 ◽  
Vol 20 (9) ◽  
pp. 2552 ◽  
Author(s):  
Ran Fang ◽  
Rongguo Song ◽  
Xin Zhao ◽  
Zhe Wang ◽  
Wei Qian ◽  
...  
Keyword(s):  
Human Body ◽  
Coplanar Waveguide ◽  
Wearable Devices ◽  
Impedance Bandwidth ◽  
Body Measurements ◽  
Uwb Antenna ◽  
Wearable Antennas ◽  
Low Profile ◽  
Close Proximity ◽  
Feeding Structure

In this article, a graphene-assembled film (GAF)-based compact and low-profile ultra-wide bandwidth (UWB) antenna is presented and tested for wearable applications. The highly conductive GAFs (~106 S/m) together with the flexible ceramic substrate ensure the flexibility and robustness of the antenna, which are two main challenges in designing wearable antennas. Two H-shaped slots are introduced on a coplanar-waveguide (CPW) feeding structure to adjust the current distribution and thus improve the antenna bandwidth. The compact GAF antenna with dimensions of 32 × 52 × 0.28 mm3 provides an impedance bandwidth of 60% (4.3–8.0 GHz) in simulation. The UWB characteristics are further confirmed by on-body measurements and show a bending insensitive bandwidth of ~67% (4.1–8.0 GHz), with the maximum gain at 7.45 GHz being 3.9 dBi and 4.1 dBi in its flat state and bent state, respectively. Our results suggest that the proposed antenna functions properly in close proximity to a human body and can sustain repetitive bending, which make it well suited for applications in wearable devices.

scholarly journals A Compact MIMO Antenna with Inverted C-Shaped Ground Branches for Mobile Terminals

2016 ◽  
Vol 2016 ◽  
pp. 1-6 ◽  
Author(s):  
Zixian Yang ◽  
Hongchun Yang ◽  
Haijuan Cui
Keyword(s):  
Correlation Coefficient ◽  
Impedance Bandwidth ◽  
Antenna Element ◽  
Planar Antenna ◽  
Mobile Terminals ◽  
Mimo Antenna ◽  
High Isolation ◽  
Operating Band ◽  
Measured Radiation ◽  
Envelope Correlation

A compact printed MIMO antenna for mobile terminals is presented. With two planar antenna elements, the −6 dB impedance bandwidth of 2.32 GHz (1.48–3.8 GHz) is obtained, which covers GSM 1800/1900, UMTS, WLAN, Wimax, S-band, and most of LTE bands. Each antenna element with a small occupation of 15 × 20 mm2consists of a driven strip and a shorted strip. Two inverted C-shaped ground branches are introduced between two elements to improve the isolation. The simulated results are studied and the measured results show that high isolation of more than 18 dB at the entire operating band is achieved. Meanwhile, the impedance performance is also improved by adding the branches. Furthermore, the measured radiation performances and envelope correlation coefficient also demonstrate that the proposed antenna could be a good candidate for mobile terminals.

Compact UWB Antenna With I-Shaped Band-Notch Parasitic Element for Laptop Applications

2009 ◽  
Vol 8 ◽  
pp. 580-582 ◽  
Author(s):  
Nakchung Choi ◽  
Changwon Jung ◽  
Joonho Byun ◽  
F.J. Harackiewicz ◽  
Myun-Joo Park ◽  
...  
Keyword(s):  
Uwb Antenna ◽  
Parasitic Element

Planar monopole antenna with wide impedance bandwidth for mobile handset application

2007 ◽  
Vol 49 (4) ◽  
pp. 779-781 ◽  
Author(s):  
Wonseob Kim ◽  
Seokjin Hong ◽  
Hoon Park ◽  
Jaehoon Choi
Keyword(s):  
Monopole Antenna ◽  
Impedance Bandwidth ◽  
Planar Monopole Antenna ◽  
Mobile Handset

scholarly journals Bandwidth Enhancement of a Bell-shaped UWB Antenna for Indoor Localization Systems

2021 ◽  
Vol 11 (1) ◽  
pp. 6691-6695
Author(s):  
M. S. Karoui ◽  
N. Ghariani ◽  
M. Lahiani ◽  
H. Ghariani
Keyword(s):  
Indoor Localization ◽  
Low Cost ◽  
Ground Plane ◽  
Wide Band ◽  
Impedance Bandwidth ◽  
Uwb Antenna ◽  
Simple Method ◽  
Bandwidth Enhancement ◽  
Measured Impedance ◽  
Localization Systems

In this paper, a simple method of enhancing the bandwidth of the Bell-shaped UWB Antenna for indoor localization systems is proposed. Therefore, a modified version of the bell-shaped Ultra-Wide Band (UWB) antenna for indoor localization systems is presented. The proposed antenna is printed on a low-cost FR-4 substrate of 21×27×1.6mm3 size. It is composed of a bell-shaped radiating patch and a multi-slotted ground plane. The measured results show that the proposed antenna has an impedance bandwidth of about 11.2GHz ranging from 3.16GHz to 14.36GHz at S11<−10dB. Compared to the original version, an enhancement of about 5.56GHz in the measured impedance bandwidth was observed.

scholarly journals A 3 – 18 GHz UWB Antenna with modified feed-line

2021 ◽  
Author(s):  
Srikanth Itapu
Keyword(s):  
Medical Imaging ◽  
Planar Waveguide ◽  
Ground Plane ◽  
Wide Band ◽  
Ultra Wide Band ◽  
Design Parameters ◽  
Impedance Bandwidth ◽  
Uwb Antenna ◽  
Feed Line ◽  
Iot Applications

Abstract A Co-Planar Waveguide fed circular ultra-wide band antenna with modified ground-plane and feedline is designed on a FR4 (ϵr=4.3) substrate of thickness 0.01λ0. The proposed antenna exhibits an overall impedance bandwidth ranging from 2.99 GHz to 18.0 GHz and beyond (with S11< -10 dB). Design parameters have been optimized to achieve the UWB bandwidth. The measured radiation patterns of this antenna are omnidirectional in H- plane and bidirectional in E-plane. An extended impedance bandwidth is achieved as a result of modified feed-line. The proposed antenna can be used for medical imaging and urban IoT applications.

Sign in / Sign up

Export Citation Format

Share Document