scholarly journals Size Effect on the Structural and Magnetic Properties of Nanosized PerovskiteLaFeO3Prepared by Different Methods

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Nguyen Thi Thuy ◽  
Dang Le Minh
Keyword(s):  
Magnetic Properties ◽  
Electron Microscope ◽  
Room Temperature ◽  
High Energy ◽  
Ferromagnetic Behavior ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation

Nanosized LaFeO3material was prepared by 3 methods: high energy milling, citrate gel, and coprecipitation. The X-ray diffraction (XRD), differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA) show that the orthorhombic LaFeO3phase was well formed at a low sintering temperature of 500°C in the citrate-gel and co-precipitation methods. Scanning electron microscope (SEM) and transmission electron microscope (TEM) observations indicate that the particle size of the LaFeO3powder varies from 10 nm to 50 nm depending on the preparation method. The magnetic properties through magnetization versus temperatureM(T)and magnetization verses magnetic fieldM(H)characteristics show that the nano-LaFeO3exhibits a weak ferromagnetic behavior in the room temperature, and theM(H)curves are well fitted by Langevin functions.

Y-Type Hexaferrites: Structural, Dielectric and Magnetic Properties

2012 ◽  
Vol 189 ◽  
pp. 209-232 ◽  
Author(s):  
Rajshree B. Jotania ◽  
Hardev Singh Virk
Keyword(s):  
Magnetic Properties ◽  
Quantum Interference ◽  
Room Temperature ◽  
Structural Changes ◽  
Ferromagnetic State ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Lcr Meter ◽  
Co Precipitation

This paper attempts to provide a historical survey of structure of various types of hexaferrites. It provides information about synthesis, characterization, structural, magnetic and dielectric properties of Y-type hexagonal ferrites using various chemical routes. We have prepared a series of cobalt doped Sr2Cu2-xCoxFe12O22(x = 0.0 to 1.0) hexaferrites using a wet chemical co-precipitation technique. The prepared hexaferrite precursors were calcined at 950 °C for 4 hours in a furnace and slowly cooled to room temperature. The crystal structure of Y-type hexaferrites is rather complicated. The chemical and structural changes were examined in detail by X-ray diffraction (XRD), Differential scanning calorimetry (DSC), Scanning electron microscopy (SEM), and Fourier transform infra-red (FTIR) spectroscopy. X-ray diffraction studies showed that sintering temperature as low as 950°C was sufficient to produce a single-phase Y-type hexaferrite material. The dielectric measurements were carried out over the frequency range of 100 Hz to 2 MHz at room temperature using an LCR meter to study the variation of dielectric constant and loss tangent with frequency. The magnetic properties of hexaferrite samples were investigated using a vibration sample magnetometer (VSM), and a superconducting quantum interference device (SQUID) magnetometer in the temperature range 30K to 200K. A change from ferromagnetic state to super paramagnetic state has been observed in Co doped Sr2Cu2-xCoxFe12O22(x= 0.6 to 1.0) hexaferrite. The novel applications of all types of hexaferrite materials have been described.

MICROSTRUCTURE AND MAGNETIC PROPERTIES CHANGE OF Fe3O4 NANOPARTICLES SYNTHESIZED UNDER MAGNETIC FIELDS AT ROOM TEMPERATURE

2009 ◽  
Vol 23 (23) ◽  
pp. 2723-2731 ◽  
Author(s):  
JUN WANG ◽  
SIHUA XIA ◽  
SHIHE CAO
Keyword(s):  
Magnetic Properties ◽  
Magnetic Fields ◽  
Room Temperature ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
Promising Technique ◽  
X Ray ◽  
Transmission Electron ◽  
Co Precipitation ◽  
Microstructure And Magnetic Properties

Magnetite nanoparticles have been synthesized by a co-precipitation method under magnetic fields (0~1 T) at room temperature. The as-prepared samples were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM), vibrating sample magnetometer (VSM) and their microstructure analysis were evaluated on a Mössbauer spectrum. It was found that the Fe 3 O 4 samples produced under a magnetic field of 1 T had a much higher saturation magnetization (15.3 emu/g) than those produced under 0.6 T (7.56 emu/g) and 0 T magnetic fields (6.59 emu/g). This interesting result implies that magnetic fields can affect the growth of Fe 3 O 4 nanoparticles and further change the microstructure and crystallinity of Fe 3 O 4 nanoparticles. It is expected that this process could also be a promising technique to improve the magnetic properties of other magnetic materials.

Effect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy Powders

2010 ◽  
Vol 654-656 ◽  
pp. 1106-1109
Author(s):  
Ya Qiong He ◽  
Chang Hui Mao ◽  
Jian Yang
Keyword(s):  
Grain Size ◽  
Magnetic Properties ◽  
Alloy Powder ◽  
High Energy ◽  
X Ray Diffraction ◽  
Powder Mixtures ◽  
X Ray ◽  
Transmission Electron ◽  
Nitridation Temperature ◽  
Microstructure And Magnetic Properties

Nanocrystalline Fe-Co alloy powders, which were prepared by high-energy mechanical milling, were nitrided under the mixing gas of NH3/H2 in the temperature range from 380°C to 510°C. X-ray diffraction (XRD) was used to analyze the grain size and reaction during the processing. The magnetic properties of the nitrided powders were measured by Vibrating Sample Magnetometer (VSM). The results show that with the appearance of Fe4N phase after nitride treatment, and the grain-size of FeCo phase decreases with the increase of nitridation temperature between 380°C to 450°C.The saturation magnetization of nitrided alloy powder treated at 480°C is about 18% higher than that of the initial Fe-Co alloy powder, accompanied by the reduction of the coercivity. Transmission electron microscope (TEM) was used, attempting to further analyze the effect of Fe4N phase on microstructure and magnetic properties of the powder mixtures.

Template Induced Synthesis of Nano-Hydroxyapatite by Co-Precipitation Method

2011 ◽  
Vol 311-313 ◽  
pp. 1713-1716 ◽  
Author(s):  
Yan Rong Sun ◽  
Tao Fan ◽  
Chang An Wang ◽  
Li Guo Ma ◽  
Feng Liu
Keyword(s):  
Electron Microscope ◽  
Chondroitin Sulfate ◽  
Aspartic Acid ◽  
Transmission Electron Microscope ◽  
Precipitation Method ◽  
X Ray Diffraction ◽  
X Ray ◽  
Structure And Morphology ◽  
Transmission Electron ◽  
Co Precipitation

Nano-hydroxyapatite with different morphology was synthesized by the co-precipitation method coupled with biomineralization using Ca(NO3)2•4H2O and (NH4)2HPO4 as reagents, adding chondroitin sulfate, agarose and aspartic acid as template. The structure and morphology of the prepared powders were characterized by X-ray diffraction (XRD) and transmission electron microscope (TEM).

Microstructure Evolution of a Fine Grain Al-50wt%Si Alloy Fabricated by High Energy Milling

2011 ◽  
Vol 479 ◽  
pp. 54-61 ◽  
Author(s):  
Fei Wang ◽  
Ya Ping Wang
Keyword(s):  
Grain Growth ◽  
Microstructure Evolution ◽  
Room Temperature ◽  
Milling Time ◽  
High Energy ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
Laser Method ◽  
X Ray ◽  
Fine Grain

Microstructure evolution of high energy milled Al-50wt%Si alloy during heat treatment at different temperature was studied. Scanning electron microscope (SEM) and X-ray diffraction (XRD) results show that the size of the alloy powders decreased with increasing milling time. The observable coarsening of Si particles was not seen below 730°C in the high energy milled alloy, whereas, for the alloy prepared by mixed Al and Si powders, the grain growth occurred at 660°C. The activation energy for the grain growth of Si particles in the high energy milled alloy was determined as about 244 kJ/mol by the differential scanning calorimetry (DSC) data analysis. The size of Si particles in the hot pressed Al-50wt%Si alloy prepared by high energy milled powders was 5-30 m at 700°C, which was significantly reduced compared to that of the original Si powders. Thermal diffusivity of the hot pressed Al-50wt%Si alloy was 55 mm2/s at room temperature which was obtained by laser method.

Influence of Gd Addition on the Structure and Capability of Ni-Mn-In Metamagnetic Shape Memory Alloys

2012 ◽  
Vol 535-537 ◽  
pp. 950-953
Author(s):  
Li Na Bai ◽  
Gui Xing Zheng ◽  
Zhi Jian Duan ◽  
Jian Jun Zhang
Keyword(s):  
Differential Scanning Calorimetry ◽  
Magnetic Properties ◽  
Magnetic Property ◽  
Transition Temperature ◽  
Martensitic Transformation ◽  
Room Temperature ◽  
Vibrating Sample Magnetometry ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray

The influences of Gd concentration on martensitic transformation and magnetic properties of NiMnIn alloys were investigated by differential scanning calorimetry (DSC) , vibrating sample magnetometry (VSM), X-ray diffraction (XRD) and etc. It is Observed through the experiment: the addition of Gd enhances martensite transition temperature;X-ray diffraction analysis of experimental alloys is revealed that to the mixture is martensite and austenite at room temperature; content of Gd is not proportional to the improvement of magnetic property.

ZnFe2O4 Modified by Fe(NO3)3 for the Synthesis of Ionic Ferrofluids

2010 ◽  
Vol 177 ◽  
pp. 32-36 ◽  
Author(s):  
An Rong Wang ◽  
Jian Li ◽  
Qing Mei Zhang ◽  
Hua Miao
Keyword(s):  
Particle Size ◽  
Magnetic Properties ◽  
Electron Microscope ◽  
Transmission Electron Microscope ◽  
Photoelectron Spectroscopy ◽  
Vibrating Sample Magnetometer ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Znfe2o4 Nanoparticles

Weak magnetic ZnFe2O4 nanoparticles were prepared by coprecipitation and treated with different concentrations of Fe(NO3)3 solution. Untreated and treated particles were studied using a vibrating sample magnetometer, transmission electron microscope, by X-ray diffraction, X-ray energy dispersive spectroscopy and X photoelectron spectroscopy. The results showed that, after treatment, the ZnFe2O4/γ-Fe2O3 forms disphase nanoparticles, with enlarged size, enhanced magnetic properties and with a surface parceled with Fe(NO3)3. The size of the particles and their magnetic properties are related to the concentration of the treatment solution. The particle size and magnetic properties could be controlled by controlling the concentration of treating solution, therefore nanoparticles can be more widely used.

Synthesis of (Y,Gd)2O3:Eu nanopowder by a novel co-precipitation processing

2004 ◽  
Vol 19 (12) ◽  
pp. 3586-3591 ◽  
Author(s):  
Jiyang Chen ◽  
Ying Shi ◽  
Jianlin Shi
Keyword(s):  
Electron Microscopy ◽  
Ammonium Hydroxide ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Hydrogen Carbonate ◽  
Ammonium Hydrogen ◽  
Intense Luminescence ◽  
Co Precipitation

Nano-sized (Y,Gd)2O3:Eu powders were synthesized by a novel co-precipitation processing in which a mixture of ammonium hydroxide and ammonium hydrogen carbonate was adopted as a complex precipitant. Evolution behaviors of precursors during calcinations were studied by means of thermogravimetry-differential scanning calorimetry-mass spectrum, Fourier transform infrared, x-ray diffraction, scanning electron microscopy, and transmission electron microscopy in detail. Nano-sized (Y,Gd)2O3:Eu powder as prepared possessed a primary grain size of about 30 nm and specific surface area of 38 m2/g after being calcined at 850 °C for 2 h, showing much finer grains and less agglomeration. The as prepared nanopowder shows intense luminescence at 611nm under x-ray or ultraviolet excitation. Transparent (Y,Gd)2O3:Eu ceramics can also be fabricated using this high sinterable nanopowder.

Room Temperature Synthesis of Cu2O Nanospheres: Optical Properties and Thermal Behavior

2014 ◽  
Vol 21 (1) ◽  
pp. 108-119 ◽  
Author(s):  
Daniela Nunes ◽  
Lídia Santos ◽  
Paulo Duarte ◽  
Ana Pimentel ◽  
Joana V. Pinto ◽  
...  
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Thermal Behavior ◽  
Room Temperature ◽  
Diffuse Reflectance Spectroscopy ◽  
Ion Beam ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron

AbstractThe present work reports a simple and easy wet chemistry synthesis of cuprous oxide (Cu2O) nanospheres at room temperature without surfactants and using different precursors. Structural characterization was carried out by X-ray diffraction, transmission electron microscopy, and scanning electron microscopy coupled with focused ion beam and energy-dispersive X-ray spectroscopy. The optical band gaps were determined from diffuse reflectance spectroscopy. The photoluminescence behavior of the as-synthesized nanospheres showed significant differences depending on the precursors used. The Cu2O nanospheres were constituted by aggregates of nanocrystals, in which an on/off emission behavior of each individual nanocrystal was identified during transmission electron microscopy observations. The thermal behavior of the Cu2O nanospheres was investigated with in situ X-ray diffraction and differential scanning calorimetry experiments. Remarkable structural differences were observed for the nanospheres annealed in air, which turned into hollow spherical structures surrounded by outsized nanocrystals.

scholarly journals Synthesis of BaTiO3 Nanoparticles via Hydrothermal Method

2017 ◽  
Vol 268 ◽  
pp. 172-176 ◽  
Author(s):  
Nurul Norfarina Hasbullah ◽  
Oon Jew Lee ◽  
Josephine Liew Ying Chyi ◽  
Soo Kien Chen ◽  
Zainal Abidin Talib
Keyword(s):  
Electron Microscope ◽  
Hydrothermal Method ◽  
Transmission Electron Microscope ◽  
Hydrothermal Process ◽  
X Ray Diffraction ◽  
Scanning Calorimetry ◽  
X Ray ◽  
Transmission Electron ◽  
Average Size ◽  
Tga And Dsc

In this work, BaTiO3 nanoparticles were synthesized through hydrothermal method. The powder obtained from the hydrothermal process (as-synthesized powder) was calcined at 1000 °C. The phase formation and morphology of the as-synthesized and calcined powders were studied using X-ray diffraction (XRD), thermogravimetric (TGA) and differential scanning calorimetry (DSC) analyzer, and transmission electron microscope (TEM). The XRD data showed that the as-synthesized powder is partially amorphous. Upon calcining the powder at 1000 °C, highly crystalline BaTiO3 with tetragonal structure was obtained. As shown by TGA and DSC analysis, the precursor powder was completely transformed into BaTiO3 at 1000 °C. The presence of BaCO3 as an impurity phase in the powder is due to the lack of Ba2+ / Ti3+/4+. Transmission electron microscope images showed that the particle size of the as-synthesized powder increased after calcination due to crystal growth. In addition, nanocubes with the average size of around 11.66 nm were obtained as a result of the calcination compared to the ellipsoid like particles of the as-synthesized powder.

Sign in / Sign up

Export Citation Format

Share Document