scholarly journals 3D Finite Element Analysis of PWA-Oil Sand Terrain System Interaction

2012 ◽  
Vol 2012 ◽  
pp. 1-10
Author(s):  
Y. Li ◽  
S. Frimpong ◽  
W. Y. Liu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Contact Area ◽  
Oil Sands ◽  
Yield Criterion ◽  
Three Dimensional ◽  
Oil Sand ◽  
Element Analysis ◽  
Nodal Displacement ◽  
Von Mises

A simulator for analyzing the interaction between the oil sand terrain and a pipe wagon articulating (PWA) system has been developed in this paper. An elastic-plastic oil sand model was built based on the finite element analysis (FEA) method and von Mises yield criterion using the Algor mechanical event simulation (MES) software. The three-dimensional (3D) distribution of the stress, strain, nodal displacement, and deformed shape of the oil sands was animated at an environmental temperature of 25°C. The 3D behavior of the oil sand terrain was investigated with different loading conditions. The effect of the load and contact area on the stress and nodal displacement was analyzed, respectively. The results indicate that both the max stress and max nodal displacement increase with the load varying from 0 to N and decrease with the contact area varying from 2 to 10 m2. The method presented in this paper forms the basis for evaluating the bearing capacity of oil sand ground.

scholarly journals Tooth-shape adaptations in aglyphous colubrid snakes inferred from three-dimensional geometric morphometrics and finite element analysis

2020 ◽  
Author(s):  
Mahdi Rajabizadeh ◽  
Sam Van Wassenbergh ◽  
Christophe Mallet ◽  
Martin Rücklin ◽  
Anthony Herrel
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Geometric Morphometrics ◽  
Yield Criterion ◽  
Three Dimensional ◽  
Sister Group ◽  
Element Analysis ◽  
Tooth Shape ◽  
Von Mises ◽  
And Function

Abstract To date there are few quantitative studies investigating the evolution of tooth shape and function in aglyphous snakes in relation to diet. A considerable evolutionary decrease in body size is observed in whip snakes of the genus Dolichophis and their sister-group Eirenis. This was coupled with a considerable shift in diet from a regime consisting mainly of prey with endoskeleton to prey bearing a hard exoskeleton. Three-dimensional (3D) geometric morphometrics revealed that the maxillary and palatine teeth of E. persicus are blunt and conical in shape, while the same teeth are sharp and elongated in E. punctatolineatus and D. schmidti. Blunt and conically shaped teeth, as observed in E. persicus, seem to be more adapted for biting hard-bodied, arthropod prey. In contrast, the sharp and elongated teeth in Dolichophis and E. punctatolineatus, are likely specialized for puncturing prey with an endoskeleton. The results of a finite element analysis confirms that during the biting of a hard-bodied prey, the generated stresses in E. persicus teeth are well below the von Mises yield criterion, while in D. schmidti the value is roughly two to three times higher, indicating that E. persicus teeth are better suited for biting hard-bodied prey such as arthropods.

A comparative study between zirconia and titanium abutments on the stress distribution in parafunctional loading: A 3D finite element analysis

2020 ◽  
Vol 28 (6) ◽  
pp. 603-613 ◽  
Author(s):  
Efe Can Sivrikaya ◽  
Mehmet Sami Guler ◽  
Muhammed Latif Bekci
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Principal Stresses ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
3D Fea ◽  
Von Mises ◽  
Three Dimensional Finite Element

BACKGROUND: Zirconia has become a popular biomaterial in dental implant systems because of its biocompatible and aesthetic properties. However, this material is more fragile than titanium so its use is limited. OBJECTIVES: The aim of this study was to compare the stresses on morse taper implant systems under parafunctional loading in different abutment materials using three-dimensional finite element analysis (3D FEA). METHODS: Four different variations were modelled. The models were created according to abutment materials (zirconia or titanium) and loading (1000 MPa vertical or oblique on abutments). The placement of the implants (diameter, 5.0 × 15 mm) were mandibular right first molar. RESULTS: In zirconia abutment models, von Mises stress (VMS) values of implants and abutments were decreased. Maximum and minimum principal stresses and VMS values increased in oblique loading. VMS values were highest in the connection level of the conical abutments in all models. CONCLUSIONS: Using conical zirconia abutments decreases von Mises stress values in abutments and implants. However, these values may exceed the pathological limits in bruxism patients. Therefore, microfractures may be related to the level of the abutment.

scholarly journals Effect of Augmentation Material Stiffness on Adjacent Vertebrae after Osteoporotic Vertebroplasty Using Finite Element Analysis with Different Loading Methods

2015 ◽  
Vol 6;18 (6;11) ◽  
pp. E1101-E1110
Author(s):  
Ah-Reum Cho
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Bone Cement ◽  
Vertebral Fractures ◽  
Three Dimensional ◽  
Element Model ◽  
Element Analysis ◽  
Adjacent Vertebral Body ◽  
Von Mises ◽  
Von Mises Stresses

Background: Vertebroplasty is an effective treatment for osteoporotic vertebral fractures, which are one of the most common fractures associated with osteoporosis. However, clinical observation has shown that the risk of adjacent vertebral body fractures may increase after vertebroplasty. The mechanism underlying adjacent vertebral body fracture after vertebroplasty is not clear; excessive stiffness resulting from polymethyl methacrylate has been suspected as an important mechanism. Objectives: The aim of our study was to compare the effects of bone cement stiffness on adjacent vertebrae after osteoporotic vertebroplasty under load-controlled versus displacementcontrolled conditions. Study Design: An experimental computer study using a finite element analysis. Setting: Medical research institute, university hospital, Korea. Methods: A three-dimensional digital anatomic model of L1/2 bone structure was reconstructed from human computed tomographic images. The reconstructed three-dimensional geometry was processed for finite element analysis such as meshing elements and applying material properties. Two boundary conditions, load-controlled and displacement-controlled methods, were applied to each of 5 deformation modes: compression, flexion, extension, lateral bending, and torsion. Results: The adjacent L1 vertebra, irrespective of augmentation, revealed nearly similar maximum von Mises stresses under the load-controlled condition. However, for the displacementcontrolled condition, the maximum von Mises stresses in the cortical bone and inferior endplate of the adjacent L1 vertebra increased significantly after cement augmentation. This increase was more significant than that with stiffer bone cement under all modes, except the torsion mode. Limitations: The finite element model was simplified, excluding muscular forces and incorporating a large volume of bone cement, to more clearly demonstrate effects of bone cement stiffness on adjacent vertebrae after vertebroplasty. Conclusion: Excessive stiffness of augmented bone cement increases the risk of adjacent vertebral fractures after vertebroplasty in an osteoporotic finite element model. This result was most prominently observed using the displacement-controlled method. Key words: Bone cements, displacement-controlled method, finite element analysis, loadcontrolled method, osteoporosis, osteoporotic fracture, polymethyl methacrylate, vertebroplasty

scholarly journals Stress distribution in a mandibular premolar after separated nickel-titanium instrument removal and root canal preparation: a three-dimensional finite element analysis

2019 ◽  
Vol 47 (4) ◽  
pp. 1555-1564 ◽  
Author(s):  
Na Ni ◽  
Jing Ye ◽  
Liyuan Wang ◽  
Simin Shen ◽  
Lei Han ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Cervical Region ◽  
Element Analysis ◽  
Straight Line ◽  
Mandibular First Premolar ◽  
Von Mises ◽  
Von Mises Stresses

Objective This study used finite element analysis (FEA) to assess the von Mises stresses of a mandibular first premolar after removing a separated instrument with an ultrasonic technique. Methods FEA models of the original and treated mandibular first premolar were reconstructed, and three models (the original canal, size 30/taper 0.04 canal, and separated instrument removal canal) were created. Two-direction (vertical and lateral) loading patterns were simulated with a 175-N force. The maximum von Mises stresses of the models within the roots from the apex to the cervical region were collected and summarized. Results Under vertical and lateral loads, all maximal values in the three models were localized in the straight-line access region. Compared with the original model (model 1), the treated models (models 2 and 3) had greater maximum stress values from the apex to the cervical region. Greater differences in the maximum von Mises stresses between models 2 and 3 were present in the straight-line access region. Conclusions Separated instrument removal caused changes in stress distribution and increases in stress concentration in the straight-line access region of roots.

Three-Dimensional Modeling and Finite Element Analysis of an Ankle External Fixator

2020 ◽  
Vol 899 ◽  
pp. 94-102
Author(s):  
Nur Faiqa Ismail ◽  
Muhammmad Aiman Firdaus Bin Adnan ◽  
Solehuddin Shuib ◽  
Nik Ahmad Hambali Nik Abd Rashid
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
External Fixator ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
External Fixators ◽  
Element Analysis ◽  
Stress And Deformation ◽  
The Stability ◽  
Von Mises

External fixator has played an important role in repairing fractured ankle bone. This surgery is done due to the several factors which are the bone is not normal position or has broken into several pieces. The external fixator will help the broken bone to grow and remodel back to the original appearance. However, there are some issues regarding to the stability of this fixation. Improper design and material are the major factor that decreased the stability since it is related to the deformation of the external fixator to hold the bone fracture area. This study aims to design a stable structure for constructing delta frame ankle external fixator to increase the stability of the fixation. There are two designs of external fixator with two types of material used in this present study. Both external fixators with different materials are analyzed in terms of von Mises stress and deformation by using a conventional Finite Element Analysis software; ANSYS Workbench V15. The result obtained shows the Model 1 with stainless steel has less stress and deformation distributions compared to the Model 2. Hence, by using Model 1 as the external fixator, the stability of the fixation can be increased.

scholarly journals To Evaluate the Influence of Different Implant Thread Designs on Stress Distribution of Osseointegrated Implant: A Three-Dimensional Finite-Element Analysis Study–An In Vitro Study

2020 ◽  
Vol 08 (01) ◽  
pp. 09-16
Author(s):  
Chhavi Sharma ◽  
Tarun Kalra ◽  
Manjit Kumar ◽  
Ajay Bansal ◽  
Anupreet Kaur Chawla
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Axial Load ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Osseointegrated Implant ◽  
Implant Therapy ◽  
Von Mises ◽  
Selection Of

Abstract Introduction Dental implants are common treatment modality for tooth loss which leads to unaesthetic appearance and may also cause deterioration of mastication and speech. The aim of implant therapy in dentistry is to restore tissue contour, function, comfort, aesthetic, and speech. Dental implant role is to transfer the mechanical force created during chewing to the supporting osseous tissues within the mandible and maxilla. The importance of biomechanical factors such as the bone-implant interface, implant thread design, the length and diameter of implants, type of loading, the quality and quantity of surrounding bone have been strained by various authors. The selection of implant thread design plays an important role in the outcome of the treatment. This study was done to evaluate the influence of different thread designs on stress distribution of osseointegrated implant using three-dimensional (3D) finite-element analysis. Materials and Methods Three implants with different thread designs, namely V-thread, buttress, and reverse buttress thread designs were considered and dimensions were standardized. The site considered was the mandibular molar region with cortical and cancellous bone assuming to be isotropic and homogeneous. The implant modeling was done with the ANSYS 18.1 software. Axial load (100N) and buccolingual load (50N) were applied. The stresses were calculated as Von Mises stress criterion. Results Minimum von mises Stress concentration was seen for tapered implant body with reverse buttress thread design under axial load 100N and tapered implant body with V-thread under buccolingual load of 50N at cortical bone which signifies bone preservation. Stress levels were observed maximum at implant and minimum at the cancellous bone. Conclusion Hence, within the limitations of this study the results obtained can be applied clinically for appropriate selection of implant thread design for a predictable success of implant therapy.

scholarly journals Tooth Shape Adaptations in Aglyphous Colubrid Snakes Inferred from 3D Geometric Morphometrics and Finite Element Analysis

2019 ◽  
Author(s):  
Mahdi Rajabizadeh ◽  
Sam Van Wassenbergh ◽  
Christophe Mallet ◽  
Martin Rücklin ◽  
Anthony Herrel
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Geometric Morphometrics ◽  
Yield Criterion ◽  
Sister Group ◽  
Element Analysis ◽  
Tooth Shape ◽  
3D Geometric Morphometrics ◽  
Von Mises Yield Criterion ◽  
Von Mises

AbstractTo date there are few detailed and quantitative studies investigating the evolution of the tooth shape and function in Aglyphous snakes in relation to diet. To study dental adaptations to diet, a lineage that is of particular interest due to its large range of adult body sizes, is the one including dwarfed snakes of the genus Eirenis and their immediate sister group, whip snakes of the genus Dolichophis. A considerable evolutionary decrease in the size is observed from a Dolichophis-like ancestor to the miniature Eirenis, coupled with a considerable shift in their diet from a regime consisting mainly of endotherms with endoskeleton to ectotherms bearing a hard exoskeleton. Maxilla, palatine, pterygoid and dentary teeth were examined in an adult and a juvenile of Dolichophis schmidti, one Eirenis punctolineatus and one Eirenis persicus. 3D Geometric Morphometrics comparison revealed maxilla and palatine teeth of the E. persicus are blunt and conical shape while those teeth are sharp and elongated in E. punctatolineatus as well as the adult and juvenile D. schmidti. A similar difference could be noted for the pterygoid teeth. In contrast, the dentary teeth are not as different among the examined snakes. Blunt and conically shaped teeth, as observed in E. persicus, seem to be more adapted for biting hard bodied, arthropod prey, while sharp and elongated teeth in Dolichophis and E. punctatolineatus, are specialized for puncturing endotherm prey. The results of a finite element analysis confirms that during biting a hard bodied prey, the generated stresses in E. persicus tooth is mostly confined to the tip of the tooth and mostly well below the von Mises yield criterion the tooth. In contrary, D. schmidti tooth appears less well suited for biting a hard prey since the generated stresses widely distribute across the tooth with values roughly 2 to 3 times higher than the von Mises yield criterion of the tooth. A lower degree of specialization that was observed among the dentary teeth in the examined snakes suggest a similar functional constraint in pushing the prey against the upper tooth rows.

Maxillary sinus pneumatization and augmentation: A three-dimensional finite element analysis

2021 ◽  
Vol 11 (11) ◽  
pp. 1892-1900
Author(s):  
Yanbo Jiang ◽  
Ming Gong ◽  
Donghui Chen ◽  
Jiaojie Li ◽  
Hailun Zhou ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Bone Graft ◽  
Maxillary Sinus ◽  
Three Dimensional ◽  
Element Analysis ◽  
3D Finite Element ◽  
Dimensional Finite Element ◽  
Von Mises ◽  
Three Dimensional Finite Element

This study aimed to explore the biomechanical behaviors of maxillary sinus elevation with bone grafts of various heights and widths using three-dimensional (3D) finite element analysis. We constructed 27 3D finite element models according to bone graft dimensions for three maxillary sinuses. These models were classified as (i) tapered, (ii) ovoid, and (iii) square. Each maxillary sinus type was analyzed with bone graft heights of 3 mm, 6 mm, and 9 mm and mesiodistal bone graft widths of 8 mm, 10 mm, and 12 mm. Different sinus pressure of 100 Pa, 500 Pa, and 1,000 Pa was applied to each aspect of the maxillary sinus. The maximum von Mises (max-VM) stress for each bone graft model was highest in the square group. The bone graft’s max-VM stress was decreased while increasing bone graft height from 3 to 9 mm in the tapered and square groups. In the ovoid group, the max-VM stress of all bone graft models decreased when the bone graft height increased from 3 to 6 mm. Thus 6 mm is the most appropriate bone graft height for all types of maxillary sinus elevation.

scholarly journals Finite Element Analysis Comparison of Plate Designs in Managing Fractures Involving the Mental Foramen

2013 ◽  
Vol 6 (2) ◽  
pp. 93-97 ◽  
Author(s):  
Neralla Mahathi ◽  
Emmanuel Azariah ◽  
C. Ravindran
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Mental Foramen ◽  
Stress Generation ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Plate Design ◽  
Von Mises ◽  
Von Mises Stresses

Introduction The aim of the study was to propose an ideal plating design for fractures running through the mental foramen. Methods The study compared three plating designs—two four-hole miniplates, 2 × 2-hole three-dimensional (3D) plate, and modified 2 × 2-hole 3D plate (posterior strut removed)—using finite element analysis. Von Mises stresses generated around the plates and bone were measured, as well as the mobility that is generated between the fracture fragments by applying muscle forces to generate bite force in one test and applying a force of 500 N over the premolars and first molar region in the second test. Results Von Mises stress in bone with miniplates measured 9.24 MPa in test 1 and 131.99 MPa in test 2. The stress with unmodified 3D plates measured 34.9 MPa in test 1 and150.03 MPa in test 2. The stress with modified 3D plates measured 24.98 MPa in test 1 and 150.59 MPa in test 2. Von Mises stress on the plates and screws measured 28.23 MPa, 95.97 MPa, 72.93 MPa in test 1 and 458.63 MPa, 779.01 MPa, 742.39 MPa in test 2 on miniplates, unmodified 3D plates, and modified 3D plates, respectively. The fracture mobility generated in the model with miniplates measured 0.001 mm in test 1 and 0.01 mm in test 2 and 0.007 mm and 0.02 mm in the model with unmodified 3D plates in test 1 and in test 2, respectively. In the model with modified 3D plates, the value was 0.001 mm and 0.01 mm in tests 1 and 2, respectively. Conclusion The ideal plate design is the two-plate technique with minimal stress generation on the bone and the hardware. The modified 3D plate has adequate strength to be used in the region but needs to be studied in detail.

scholarly journals Stress Distribution on the Prosthetic Screws in the All-on-4 Concept: A Three-Dimensional Finite Element Analysis

2020 ◽  
Vol 46 (1) ◽  
pp. 3-12
Author(s):  
Ji-Hyeon Oh ◽  
Young-Seong Kim ◽  
Joong Yeon Lim ◽  
Byung-Ho Choi
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Dimensional Finite Element ◽  
Edentulous Patients ◽  
Von Mises ◽  
Three Dimensional Finite Element

The all-on-4 concept, which is used to rehabilitate edentulous patients, can present with mechanical complications such as screw loosening and fracture. The purpose of this study was to evaluate the stress patterns induced in the prosthetic screws by the different prosthetic screw and abutment designs in the all-on-4 concept using finite element analysis. Von Mises stress values on 6 groups of each screw type, including short and narrow screw, short abutment; short and wide screw, short abutment; long and wide screw, short abutment; short and narrow screw, long abutment; short and wide screw, long abutment; and long and wide screw, long abutment, were compared under a cantilever loading of 200 N that was applied on the farther posterior to the position of the connection between the distal implant and the metal framework. Posterior prosthetic screws showed higher stress values than anterior prosthetic screws. The stress values in posterior prosthetic screws decreased as the length and diameter increased. In conclusion, the long and wide screw design offers advantages in stress distribution when compared with the short and narrow design.

Sign in / Sign up

Export Citation Format

Share Document