scholarly journals The Experimental Performance of an Unglazed PVT Collector with Two Different Absorber Types

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Jin-Hee Kim ◽  
Jun-Tae Kim
Keyword(s):  
Thermal Energy ◽  
Electrical Performance ◽  
Experimental Performance ◽  
Photovoltaic Modules ◽  
Glass Cover ◽  
Pv Module ◽  
Pv Modules ◽  
Solar Thermal Collectors ◽  
Tube Type ◽  
Liquid Type

Photovoltaic-thermal collectors combine photovoltaic modules and solar thermal collectors, forming a single device that produces electricity and heat simultaneously. There are two types of liquid-type PVT collectors, depending on the existence or absence of a glass cover over the PV module. The glass-covered (glazed) PVT collector produces relatively more thermal energy but has a lower electrical yield, whereas the uncovered (unglazed) PVT collector has a relatively low thermal energy and somewhat higher electrical performance. The thermal and electrical performance of liquid-type PVT collectors is related not only to the collector design, such as whether a glass cover is used, but also to the absorber design, that is, whether the absorber is for the sheet-and-tube type or the fully wetted type. The design of the absorber, as it comes into contact with the PV modules and the liquid tubes, is regarded as important, as it is related to the heat transfer from the PV modules to the liquid in the tubes. In this paper, the experimental performance of two liquid-type PVT collectors, a sheet-and-tube type and a fully wetted type, was analyzed.

scholarly journals Comparison of Electrical and Thermal Performances of Glazed and Unglazed PVT Collectors

2012 ◽  
Vol 2012 ◽  
pp. 1-7 ◽  
Author(s):  
Jin-Hee Kim ◽  
Jun-Tae Kim
Keyword(s):  
Thermal Energy ◽  
Energy Performance ◽  
Solar Thermal ◽  
Electrical Performance ◽  
Unit Surface Area ◽  
Electrical Efficiency ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Solar Thermal Collectors ◽  
Liquid Type

Photovoltaic-thermal (PVT) collectors combine photovoltaic modules and solar thermal collectors, forming a single device that receives solar radiation and produces electricity and heat simultaneously. PVT collectors can produce more energy per unit surface area than side-by-side PV modules and solar thermal collectors. There are two types of liquid-type flat-plate PVT collectors, depending on the existence of glass cover over PV module: glass-covered (glazed) PVT collectors, which produce relatively more thermal energy but have lower electrical yield, and uncovered (unglazed) PVT collectors, which have relatively lower thermal energy with somewhat higher electrical performance. In this paper, the experimental performance of two types of liquid-type PVT collectors, glazed and unglazed, was analyzed. The electrical and thermal performances of the PVT collectors were measured in outdoor conditions, and the results were compared. The results show that the thermal efficiency of the glazed PVT collector is higher than that of the unglazed PVT collector, but the unglazed collector had higher electrical efficiency than the glazed collector. The overall energy performance of the collectors was compared by combining the values of the average thermal and electrical efficiency.

scholarly journals Soiling of Photovoltaic Modules: Comparing between Two Distinct Locations within the Framework of Developing the Photovoltaic Soiling Index (PVSI)

2019 ◽  
Vol 11 (17) ◽  
pp. 4697 ◽  
Author(s):  
Thamer Alquthami ◽  
Karim Menoufi
Keyword(s):  
Simple Procedure ◽  
Outdoor Environment ◽  
Electrical Performance ◽  
Dust Density ◽  
Photovoltaic Modules ◽  
Future Performance ◽  
Pv Module ◽  
Pv Modules ◽  
Interactive Map ◽  
The Impact

This article evaluates the impact of dust accumulation on the performance of photovoltaic (PV) modules in two different locations inside Egypt, Cairo and Beni-Suef. Two identical PV modules were used for that purpose, where each module was exposed to the outdoor environment in order to collect dust naturally for a period of three weeks, each in its corresponding location. The approximate dust density on each of the two PV modules was estimated. Moreover, the electrical performance was evaluated and compared under the same indoor testing conditions. The results show a better electrical performance and less dust density for the PV module located in Cairo compared to that located in Beni-Suef. The results further provide an indication for the impact of soling in different locations within the same country through a clear and simple procedure. In addition, it paves the way for establishing a Photovoltaic Soiling Index (PVSI) in terms of a Photovoltaic Dust Coefficient, as well as a Photovoltaic Dust Interactive Map. The product of such concepts could be used by the Photovoltaic systems designers everywhere in order to estimate the impact of dust on the future performance of PV modules in small and large installations in different regions around the globe, and during different times of the year as well.

scholarly journals A Study of Optimal Specifications for Light Shelves with Photovoltaic Modules to Improve Indoor Comfort and Save Building Energy

2021 ◽  
Vol 18 (5) ◽  
pp. 2574
Author(s):  
Heangwoo Lee ◽  
Xiaolong Zhao ◽  
Janghoo Seo
Keyword(s):  
Energy Savings ◽  
Building Energy ◽  
Energy Performance ◽  
Building Energy Efficiency ◽  
Efficiency Change ◽  
Photovoltaic Modules ◽  
Heating And Cooling ◽  
Pv Module ◽  
Pv Modules ◽  
Indoor Comfort

Recent studies on light shelves found that building energy efficiency could be maximized by applying photovoltaic (PV) modules to light shelf reflectors. Although PV modules generate a substantial amount of heat and change the consumption of indoor heating and cooling energy, performance evaluations carried out thus far have not considered these factors. This study validated the effectiveness of PV module light shelves and determined optimal specifications while considering heating and cooling energy savings. A full-scale testbed was built to evaluate performance according to light shelf variables. The uniformity ratio was found to improve according to the light shelf angle value and decreased as the PV module installation area increased. It was determined that PV modules should be considered in the design of light shelves as their daylighting and concentration efficiency change according to their angles. PV modules installed on light shelves were also found to change the indoor cooling and heating environment; the degree of such change increased as the area of the PV module increased. Lastly, light shelf specifications for reducing building energy, including heating and cooling energy, were not found to apply to PV modules since PV modules on light shelf reflectors increase building energy consumption.

scholarly journals An Improved Generalized Method for Evaluation of Parameters, Modeling, and Simulation of Photovoltaic Modules

2017 ◽  
Vol 2017 ◽  
pp. 1-19 ◽  
Author(s):  
Vandana Jha ◽  
Uday Shankar Triar
Keyword(s):  
Modeling And Simulation ◽  
Standard Test ◽  
Unknown Parameters ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Test Conditions ◽  
Pv Modules ◽  
Evaluation Of Parameters ◽  
Output Characteristics ◽  
Matlab Programming

This paper proposes an improved generalized method for evaluation of parameters, modeling, and simulation of photovoltaic modules. A new concept “Level of Improvement” has been proposed for evaluating unknown parameters of the nonlinear I-V equation of the single-diode model of PV module at any environmental condition, taking the manufacturer-specified data at Standard Test Conditions as inputs. The main contribution of the new concept is the improvement in the accuracy of values of evaluated parameters up to various levels and is based on mathematical equations of PV modules. The proposed evaluating method is implemented by MATLAB programming and, for demonstration, by using the values of parameters of the I-V equation obtained from programming results, a PV module model is build with MATLAB. The parameters evaluated by the proposed technique are validated with the datasheet values of six different commercially available PV modules (thin film, monocrystalline, and polycrystalline) at Standard Test Conditions and Nominal Operating Cell Temperature Conditions. The module output characteristics generated by the proposed method are validated with experimental data of FS-270 PV module. The effects of variation of ideality factor and resistances on output characteristics are also studied. The superiority of the proposed technique is proved.

scholarly journals Performance evaluation of polycrystalline photovoltaic modules in a Guinea Savanna and Mangrove swamp

2021 ◽  
Vol 4 (1) ◽  
pp. 011-021
Author(s):  
Nsed Ayip Akonjom ◽  
John Iyang Umuji ◽  
Ukoette Jeremiah Ekah
Keyword(s):  
Relative Humidity ◽  
Solar Power ◽  
Solar Flux ◽  
Mangrove Swamp ◽  
Cross River State ◽  
Photovoltaic Modules ◽  
Power Meter ◽  
Guinea Savanna ◽  
Pv Module ◽  
Pv Modules

This central idea of this research is to investigate how voltage, current, power output and efficiency of polycrystalline photovoltaic (PV) modules installed in a Guinea Savanna and Mangrove Swamp is affected by temperature, relative humidity and irradiance. The study locations are Calabar (mangrove swamp) and Ogoja (guinea savanna), in Cross River State, Nigeria. Two polycrystalline PV modules of exact specification mounted on a platform one-metre-high above the ground were used. A digital solar power meter (SM206) and a digital solar flux meter (MS 6616) was used to monitor and measure solar power and solar flux reaching the PV modules. A digital hygrometer and thermometer (KT-908) were used to monitor and measure the relative humidity and ambient temperature level at the height of installation and a digital multimeter (M880C+) accompanied with a temperature sensor was used to monitor voltage, current and panel temperature values from the modules. Analysis of the collected data reveals that the efficiency of the modules were not constant throughout the day. However, a higher voltage production and efficiency level was obtained for the PV module installed in Ogoja than that installed in Calabar under their respective levels of relative humidity, temperature and irradiance.

scholarly journals Design of PV Modules Including a Layer between Solar Cells and Glass Cover to Increase PV Module Lifetime

2018 ◽  
Vol 182 (19) ◽  
pp. 18-23
Author(s):  
M. Mokhtar ◽  
Wagdy R. ◽  
Mohamed Abouelatta ◽  
A. I.
Keyword(s):  
Solar Cells ◽  
Glass Cover ◽  
Pv Module ◽  
Pv Modules

scholarly journals Modeling of Photovoltaic Module Using the MATLAB

2019 ◽  
Vol 9 ◽  
pp. 59-69
Author(s):  
Alok Dhaundiyal ◽  
Divine Atsu
Keyword(s):  
Standard Test ◽  
Electrical Performance ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Pv Module ◽  
Proposed Model ◽  
Current Voltage ◽  
Pv Modules ◽  
The Impact ◽  
The Mathematical Model

This paper presents the modeling and simulation of the characteristics and electrical performance of photovoltaic (PV) solar modules. Genetic coding is applied to obtain the optimized values of parameters within the constraint limit using the software MATLAB. A single diode model is proposed, considering the series and shunt resistances, to study the impact of solar irradiance and temperature on the power-voltage (P-V) and current-voltage (I-V) characteristics and predict the output of solar PV modules. The validation of the model under the standard test conditions (STC) and different values of temperature and insolation is performed, as well as an evaluation using experimentally obtained data from outdoor operating PV modules. The obtained results are also subjected to comply with the manufacturer’s data to ensure that the proposed model does not violate the prescribed tolerance range. The range of variation in current and voltage lies in the domain of 8.21 – 8.5 A and 22 – 23 V, respectively; while the predicted solutions for current and voltage vary from 8.28 – 8.68 A and 23.79 – 24.44 V, respectively. The measured experimental power of the PV module estimated to be 148 – 152 W is predicted from the mathematical model and the obtained values of simulated solution are in the domain of 149 – 157 W. The proposed scheme was found to be very effective at determining the influence of input factors on the modules, which is difficult to determine through experimental means.

scholarly journals Electric Ferry Ecosystem for Sustainable Inter-Island Transport in Philippines: A Pilot Study

2018 ◽  
Vol 8 (6) ◽  
pp. 3570-3575
Author(s):  
E. V. Palconit ◽  
M. L. S. Abundo
Keyword(s):  
Energy Consumption ◽  
Pilot Study ◽  
Energy Management ◽  
Electric Propulsion ◽  
The Other ◽  
Energy Management System ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
First Case ◽  
Pv Modules

An electric boat system as a pilot study for the electric ferry was designed and field-tested in Samal Island, Philippines, to verify sustainability for inter-island transport. This pilot study uses 4.5m monohull with a displacement weight of 343kg. During the experiment, two cases were compared: in the first case the boat was powered solely with batteries and in the other case with the aid of photovoltaic (PV) modules. For the first case, 24V electric propulsion was driven by two 12V, 100Ah batteries, which resulted to a navigational range of around 18, 16 and 15 trips with energy consumption of 111.64Wh, 117.19Wh and 123.92Wh respectively. In the second case, the photovoltaic modules were attached on the boat to supplement the PV used while on sail. Results in the second case showed that PV module supplemented energy was about to 13.4%, 26.8% and 38.7% using three different speeds like 3.18, 3.32 and 3.84knots and the navigational range extended to 4km, 1km, and 14.4km respectively. Therefore, the electric boat with the aid of PV module answers the problem in the energy management system that deals with the sustainability of the system in the inter-island transport in Philippines.

Measurements and Characterization of Photovoltaic Modules for Tolerance Verification

2013 ◽  
pp. 144-152
Author(s):  
C. Calò ◽  
A. Lay-Ekuakille ◽  
P. Vergallo ◽  
C. Chiffi ◽  
A. Trotta ◽  
...  
Keyword(s):  
Digital Imaging ◽  
Failure Mechanisms ◽  
Matrix Methods ◽  
Energy Prediction ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Pv Modules ◽  
Tolerance Verification ◽  
Material Tests

One of the most important aspects of photovoltaic modules is reliability for future uses, that is, a certain module will last certain number of years in use (generally 30 or 35 years). Reliability yields from excellent qualification tests on photovoltaic (PV) modules. Testing for reliability identifies unknown failure mechanisms and whether modules are susceptible to known failure mechanisms. This paper illustrates techniques of outdoor measurements and qualification characterization to know PV module conditions for commercial uses. Matrix methods are used for energy prediction. Failure material tests, using digital imaging and thermography, have also been conducted.

scholarly journals Outdoor Performance Test of Bifacial n-Type Silicon Photovoltaic Modules

2019 ◽  
Vol 11 (22) ◽  
pp. 6234 ◽  
Author(s):  
Hyeonwook Park ◽  
Sungho Chang ◽  
Sanghwan Park ◽  
Woo Kyoung Kim
Keyword(s):  
Tilt Angle ◽  
Performance Test ◽  
Power Production ◽  
Energy Yield ◽  
Concrete Floor ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Pv Modules ◽  
Solar Tracker ◽  
One Year

The outdoor performance of n-type bifacial Si photovoltaic (PV) modules and string systems was evaluated for two different albedo (ground reflection) conditions, i.e., 21% and 79%. Both monofacial and bifacial silicon PV modules were prepared using n-type bifacial Si passivated emitter rear totally diffused cells with multi-wire busbar incorporated with a white and transparent back-sheet, respectively. In the first set of tests, the power production of the bifacial PV string system was compared with the monofacial PV string system installed on a grey concrete floor with an albedo of ~21% for approximately one year (June 2016–May 2017). In the second test, the gain of the bifacial PV string system installed on the white membrane floor with an albedo of ~79% was evaluated for approximately ten months (November 2016–August 2017). During the second test, the power production by an equivalent monofacial module installed on a horizontal solar tracker was also monitored. The gain was estimated by comparing the energy yield of the bifacial PV module with that of the monofacial module. For the 1.5 kW PV string systems with a 30° tilt angle to the south and 21% ground albedo, the year-wide average bifacial gain was determined to be 10.5%. An increase of the ground albedo to 79% improved the bifacial gain to 33.3%. During the same period, the horizontal single-axis tracker yielded an energy gain of 15.8%.

Sign in / Sign up

Export Citation Format

Share Document