scholarly journals Squeezing Force of the Magnetorheological Fluid Isolating Damper for Centrifugal Fan in Nuclear Power Plant

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Jin Huang ◽  
Ping Wang ◽  
Guochao Wang
Keyword(s):  
Nuclear Power ◽  
Theoretical Foundation ◽  
Fluid Dynamic ◽  
Flow Behavior ◽  
Magnetorheological Fluid ◽  
Centrifugal Fan ◽  
Parallel Channel ◽  
Mr Fluid ◽  
Mr Fluids ◽  
Control Devices

Magnetorheological (MR) disk-type isolating dampers are the semi-active control devices that use MR fluids to produce controllable squeezing force. In this paper, the analytical endeavor into the fluid dynamic modeling of an MR isolating damper is reported. The velocity and pressure distribution of an MR fluid operating in an axisymmetric squeeze model are analytically solved using a biviscosity constitutive model. Analytical solutions for the flow behavior of MR fluid flowing through the parallel channel are obtained. The equation for the squeezing force is derived to provide the theoretical foundation for the design of the isolating damper. The result shows that with the increase of the applied magnetic field strength, the squeezing force is increased.

Thermal and tribological performance of graphite flake based magnetorheological fluid under shear mode clutch

2021 ◽  
pp. 1-24
Author(s):  
Manish Kumar Thakur ◽  
Chiranjit Sarkar
Keyword(s):  
Research Work ◽  
Magnetorheological Fluid ◽  
Tribological Performance ◽  
Graphite Flake ◽  
Shear Mode ◽  
Torque Sensor ◽  
Test Rig ◽  
Mr Fluid ◽  
Mr Fluids ◽  
Torque Transmission

Abstract In this research work, graphite flake has been used as an additive in magnetorheological (MR) fluid to improve its thermal and tribological performance. MR fluids with varying amounts of graphite flakes (0.5, 1, 2, 3, 4, and 5 wt%) are prepared to show effective thermal and tribological performance. A test rig is developed with a DC motor, torque sensor, and MR clutch operated in a shear mode to test the torque transmission. Results show the lubrication effects of graphite flakes in MR fluid. Torque transmission is improved in on-state and off-state using graphite flakes based MR fluid as compared to conventional MR fluid. Heating of MR clutch is also reduced with the graphite flakes based MR fluid. Wear marks and damages are decreased significantly with the increased amount of graphite flakes as found in surface roughness tests. SEM and EDS are used to characterize the worn surfaces. This research provides information about the effectiveness of graphite flakes in the MR clutch to improve the device's performance.

scholarly journals Enhanced Magnetorheological Performance of Carbonyl Iron Suspension Added With Barium Ferrite Nanoparticle

2021 ◽  
Vol 8 ◽  
Author(s):  
Hyo Seon Jang ◽  
Qi Lu ◽  
Hyoung Jin Choi
Keyword(s):  
Magnetic Field ◽  
Carbonyl Iron ◽  
Barium Ferrite ◽  
Flow Behavior ◽  
Vibrating Sample Magnetometry ◽  
Mr Fluid ◽  
Mr Fluids ◽  
Ferrite Nanoparticle ◽  
The Magnetic Field ◽  
Mr Characteristics

Hard-magnetic barium ferrite (BF) nanoparticles with a hexagonal plate-like structure were used as an additive to a carbonyl iron (CI) microparticle-based magnetorheological (MR) fluid. The morphology of the pristine CI and CI/BF mixture particles was examined by scanning electron microscopy. The saturation magnetization and coercivity values of each particle were measured in the powder state by vibrating sample magnetometry. The MR characteristics of the CI/BF MR fluid measured using a rotation rheometer under a range of magnetic field strengths were compared with those of the CI-based MR fluid. The flow behavior of both MR fluids was fitted using a Herschel–Bulkley model, and their stress relaxation phenomenon was examined using the Schwarzl equation. The MR fluid with the BF additive showed higher dynamic and elastic yield stresses than the MR fluid without the BF additive as the magnetic field strength increased. Furthermore, the BF nanoparticles embedded in the space between the CI microparticles improved the dispersion stability and the MR performance of the MR fluid.

scholarly journals In-situ Capacitance Sensing for the Settlement of Magnetorheological Fluid: Simulation and Experiments

2021 ◽  
Vol 8 ◽  
Author(s):  
Honghui Zhang ◽  
Zhiyuan Zou ◽  
Na An ◽  
Ningsong Xiong ◽  
Xu Yang
Keyword(s):  
Mr Damper ◽  
Magnetorheological Fluid ◽  
Fluid Simulation ◽  
Mr Fluid ◽  
Key Indicator ◽  
Mr Fluids ◽  
The Status ◽  
Long Time ◽  
The Relationship

In light of the insurmountable sedimentation of magnetorheological (MR) fluid, it is of great significance to ensure the performability of an MR damper by introducing a sensing method for MR fluid settling, and a key indicator to identify the health status of the MR damper is critical. However, the settling monitoring system for MR fluid can nowadays only function in a laboratory with transparent and non-magnetic tubes, which is not qualified for the in-situ sensing in a steel-made cylinder. Under the analysis of an open plate capacitor (OPC) configuration, the relationship between the concentration of magnetorheological fluid and the capacitance is investigated by simulation and experiments, and based on OPC, an in-situ sensing method for the settlement monitoring of magnetorheological fluid is designed. Long-time settling monitoring is carried out with home-made MR fluids, and the test results show that the sensing method can effectively reflect the status of settled MR fluids, and has the potential to be utilized in the identification of MR fluid compression points, which provides the strategic signal for the probable active or operational re-dispersing of MR fluid.

Magnetorheological Damping of Fragment Barrier Suspension Systems

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
Kwon Joong Son ◽  
Eric P. Fahrenthold
Keyword(s):  
Ballistic Performance ◽  
Mr Fluid ◽  
Suspension Systems ◽  
Mr Fluids ◽  
Ballistic Protection ◽  
Protection Systems ◽  
Fluid Damping ◽  
Magnetorheological Damping ◽  
Impact Experiments ◽  
Very High

Magnetorheological (MR) fluids, well established as components of a variety of suspension systems, may offer opportunities to improve the performance of fabric ballistic protection systems, which typically do not incorporate significant energy dissipation mechanisms. A series of ballistic impact experiments has been conducted to investigate the potential of MR fluid damped fabric suspension systems to improve upon current fabric barrier designs. The results indicate that for the simple fabric suspension systems tested, MR fluid damping does not improve upon the very high weight specific ballistic performance of state of the art aramid fibers.

Dynamic characteristics of squeeze-type mount using magnetorheological fluid

2005 ◽  
Vol 219 (1) ◽  
pp. 27-34 ◽  
Author(s):  
Y K Ahn ◽  
J-Y Ha ◽  
Y-H Kim ◽  
B-S Yang ◽  
M Ahmadian ◽  
...  
Keyword(s):  
Dynamic Characteristics ◽  
Experimental Analysis ◽  
Vibration Isolation ◽  
Dynamic Behaviour ◽  
Electrical Current ◽  
Magnetorheological Fluid ◽  
Test Set ◽  
Mr Fluid ◽  
Set Up ◽  
Stiffness And Damping

This paper presents an analytical and experimental analysis of the characteristics of a squeeze-type magnetorheological (MR) mount which can be used for various vibration isolation areas. The concept of the squeeze-type mount and details of the design of a squeeze-type MR mount are discussed. These are followed by a detailed description of the test set-up for evaluating the dynamic behaviour of the mount. A series of tests was conducted on the prototype mount built for this study, in order to characterize the changes occurring as a result of changing electrical current to the mount. The results of this study show that increasing electrical current to the mount, which increases the yield stress of the MR fluid, will result in an increase in both stiffness and damping of the mount. The results also show that the mount hysteresis increases with increase in current to the MR fluid, causing changes in stiffness and damping at different input frequencies.

Internal Organizational Measurement for Control of Magnetorheological Fluid Properties

2006 ◽  
Vol 129 (4) ◽  
pp. 423-428 ◽  
Author(s):  
John R. Lloyd ◽  
Miquel O. Hayesmichel ◽  
Clark J. Radcliffe
Keyword(s):  
Magnetic Field ◽  
Physical Properties ◽  
High Sensitivity ◽  
Time Varying ◽  
Measurable Effect ◽  
Mr Fluid ◽  
Fluid State ◽  
Mr Fluids ◽  
Fluid Properties ◽  
Field Excitation

Magnetorheological (MR) fluids change their physical properties when subjected to a magnetic field. As this change occurs, the specific values of the physical properties are a function of the fluid’s time-varying organization state. This results in a nonlinear, hysteretic, time-varying fluid property response to direct magnetic field excitation. Permeability, resistivity and permittivity changes of MR fluid were investigated and their suitability to indicate the organizational state of the fluid, and thus other transport properties, was determined. High sensitivity of permittivity and resistivity to particle organization and applied field was studied experimentally. The measurable effect of these material properties can be used to implement an MR fluid state sensor.

Measurement of Flow-Induced Forces: A Single Flexible Tube in a Rigid Triangular-Pitch Bundle Subjected to Two-Phase Cross-Flow

2015 ◽  
Author(s):  
Enrico Deri ◽  
Joël Nibas ◽  
Olivier Ries ◽  
André Adobes
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Tube Bundle ◽  
Fluid Dynamic ◽  
Cross Flow ◽  
Maintenance Policy ◽  
Excitation Spectra ◽  
Two Phase ◽  
Force Coefficients ◽  
Out Of Plane

Flow-induced vibrations of Steam Generator tube bundles are a major concern for the operators of nuclear power plants. In order to predict damages due to such vibrations, EDF has developed the numerical tool GeViBus, which allows one to asses risk and thereafter to optimize the SG maintenance policy. The software is based on a semi analytical model of fluid-dynamic forces and dimensionless fluid force coefficients which need to be assessed by experiment. The database of dimensionless coefficients is updated in order to cover all existing tube bundle configurations. Within this framework, a new test rig was presented in a previous conference with the aim of assessing parallel triangular tube arrangement submitted to a two-phase cross-flow. This paper presents the result of the first phase of the associated experiments in terms of force coefficients and two-phase flow excitation spectra for both in-plane and out-of-plane vibration.

scholarly journals Prediction of flow-control devices' noise with modified acoustic perturbation equations

2020 ◽  
Vol 22 (3) ◽  
pp. 619-627
Author(s):  
Luca Fenini ◽  
Stefano Malavasi
Keyword(s):  
Flow Control ◽  
Fluid Dynamic ◽  
International Standards ◽  
The Other ◽  
Computational Time ◽  
Noise Prediction ◽  
Acoustic Perturbation ◽  
Flow Control Devices ◽  
Control Devices ◽  
Perturbation Equations

Abstract Fluid-dynamic noise emissions produced by flow-control devices inside ducts are a concerning issue for valve manufacturers and pipeline management. This work proposes a modified formulation of Acoustic Perturbation Equations (APE) that is applicable to industrial frameworks where the interest is addressed to noise prediction according to international standards. This formulation is derived from a literature APE system removing two terms allowing for a computational time reduction of about 20%. The physical contribution of the removed terms is discussed according to the literature. The modified APE are applied to the prediction of the noise emitted by an orifice. The reliability of the new APE system is evaluated by comparing the Sound Pressure Level (SPL) and the acoustic pressure with the ones returned by LES and literature APE. The new formulation agrees with the other methods far from the orifice: moving over nine diameters downstream of the trailing edge, the SPL is in accordance with the other models. Since international standards characterize control devices with the noise measured 1 m downstream of them, the modified APE formulation provides reliable and faster noise prediction for those devices with outlet diameter, d, such that 9d < 1 m.

CFD Prediction of the Effects of Surface Roughness on Elastohydrodynamic Lubrication under Rolling/Sliding Conditions

2012 ◽  
Vol 184-185 ◽  
pp. 86-89 ◽  
Author(s):  
Shian Gao ◽  
Sutthinan Srirattayawong
Keyword(s):  
Surface Roughness ◽  
Shear Stress ◽  
Fluid Dynamic ◽  
Flow Behavior ◽  
Elastohydrodynamic Lubrication ◽  
Pressure Profile ◽  
Hertzian Contact ◽  
Pure Rolling ◽  
Large Fluctuations ◽  
Two Parameters

The surface roughness plays an important role in elastohydrodynamic lubrication (EHL). To improve the lubrication system the flow behavior and lubrication mechanism must be understood, especially in the thin film classification. The effects of surface roughness in the EHL problem are complicated and difficult to measure by experiment. Therefore numerical simulation using the computational fluid dynamic (CFD) approach is proposed in this research. The CFD model developed has taken the arbitrary surface roughness into consideration, and has been used to predict the characteristics of fluid flow, such as the pressure distribution, the minimal film thickness and the shear stress. The cylinder is considered to be under elastic deformation according to the theory of Hertzian contact and the surface of cylinder is defined to have an arbitrary roughness. The simulation results show that the surface roughness has significant effects on the pressure profile and shear stress, especially in the case of pure rolling, where the two parameters in the rough surface case show large fluctuations that are much higher than the corresponding smooth surface case.

Effect of Internal Pressure on Flow Properties of Magnetorheological Fluids

2011 ◽  
Author(s):  
Andrea Spaggiari ◽  
Eugenio Dragoni
Keyword(s):  
Internal Pressure ◽  
System Design ◽  
Flow Mode ◽  
Shear Mode ◽  
Mr Fluid ◽  
Mr Fluids ◽  
Experimental Apparatus ◽  
Gear Pumps ◽  
Strengthen Effect ◽  
Hydraulic System Design

Magnetorheological (MR) fluids have a lot of applications in the industrial world, but sometimes their properties are not performing enough to meet system requirements. It has been found that in shear mode MR fluids exhibits a pressure dependency called squeeze strengthen effect. Since a lot of MR fluid based devices work in flow mode (i.e. dampers) this paper investigates the behaviour in flow mode under pressure. The system design is articulated in three steps: hydraulic system design, magnetic circuit design and design of experiment. The experimental apparatus is a cylinder in which a translating piston displaces the fluid without the use of standard gear pumps, incompatible with MR fluids. The experimental apparatus measures the MR fluid yield stress as a function of pressure and magnetic field allowing the yield shear stress to be calculated. A statistical analysis of the results shows that the squeeze strengthen effect is present in flow mode as well and the presence of internal pressure is able to enhance the performance of MR fluid by nearly ten times.

Sign in / Sign up

Export Citation Format

Share Document