scholarly journals Photocatalytic Degradation of Dichlorvos in Visible Light byMg2+-TiO2Nanocatalyst

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
T. Siva Rao ◽  
Teshome Abdo Segne ◽  
T. Susmitha ◽  
A. Balaram Kiran ◽  
C. Subrahmanyam
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Visible Region ◽  
Sem Images ◽  
Xps Spectra ◽  
X Ray ◽  
Adsorption Desorption

Photocatalytic activity of TiO2was studied by doping with magnesium (Mg2+-TiO2) with varying magnesium weight percentages ranging from 0.75–1.5 wt%. The doped and undoped samples were synthesized by sol-gel method and characterized by X-ray diffraction (XRD), N2adsorption-desorption (BET), X-ray photoelectron spectroscopy (XPS), UV-visible diffuse reflectance spectroscopy (DRS), and scanning electron microscopy (SEM). The XRD data has shown that anatase crystalline phase in Mg2+-TiO2catalysts, indicating that Mg2+ions did not influence the crystal patterns of TiO2. The presence of magnesium ions in TiO2matrix has been determined by XPS spectra. DRS spectra showed that there is a significant absorption shift towards the visible region for doped TiO2. The SEM images and BET results showed that doped catalyst has smaller particle size and highest surface area than undoped TiO2. The photocatalytic efficiency of the synthesized catalysts was investigated by the photocatalytic degradation of aqueous dichlorvos (DDVP) under visible light irradiation, and it was found that the Mg2+-doped catalysts have better catalytic activity than undoped TiO2. This can be attributed that there is a more efficient electron-hole creation in Mg2+-TiO2in visible light, contrary to undoped TiO2which can be excited only in UV irradiation. The effect of dopant concentration, pH of solution, dosage of catalysts, and initial pesticide concentration has been studied.

VISIBLE LIGHT ACTIVE Cu2+/TiO2 NANOCATALYST FOR DEGRADATION OF DICHLORVOS

2012 ◽  
Vol 11 (05) ◽  
pp. 1250030 ◽  
Author(s):  
TESHOME ABDO SEGNE ◽  
SIVA RAO TIRUKKOVALLURI ◽  
SUBRAHMANYAM CHALLAPALLI
Keyword(s):  
Catalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Light Illumination ◽  
X Ray ◽  
Photo Catalytic Activity ◽  
Visible Light Active ◽  
Adsorption Desorption

The advantage of doping of TiO2 with copper has been utilized for enhanced degradation of pesticide under visible light irradiation. The sol–gel method has been undertaken for the synthesis of copper-doped TiO2 by varying the dopant loadings from 0.25 wt.% to 1.0 wt.% of Cu2+ . The doped samples were characterized by UV-Visible Diffuse Reflectance Spectroscopy (DRS), N2 adsorption–desorption (BET), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscopy (SEM), and Energy Dispersive Spectrometry (EDS). The photocatalytic activity of the catalyst was tested by degradation of dichlorvos under visible light illumination. The results found that 0.75 wt.% of Cu2+ doped nanocatalysts have better photo catalytic activity than the rest of percentages doped, undoped TiO2 and Degussa P25. The reduction of band gap was estimated and the influence of the process parameters on photo catalytic activity of the catalyst has been explained.

scholarly journals Neodymium-DopedTiO2with Anatase and Brookite Two Phases: Mechanism for Photocatalytic Activity Enhancement under Visible Light and the Role of Electron

2012 ◽  
Vol 2012 ◽  
pp. 1-10 ◽  
Author(s):  
Douga Nassoko ◽  
Yan-Fang Li ◽  
Jia-Lin Li ◽  
Xi Li ◽  
Ying Yu
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photocatalytic Degradation ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Organic Pollutant ◽  
Sol Gel ◽  
Reactive Species ◽  
X Ray ◽  
Photogenerated Electrons

Titanium dioxide (TiO2) doped with neodymium (Nd), one rare earth element, has been synthesized by a sol-gel method for the photocatalytic degradation of rhodamine-B under visible light. The prepared samples are characterized by X-ray diffractometer, Raman spectroscopy, UV-Vis diffuse reflectance spectroscopy, X-ray photoelectron spectroscopy, and Brunauer-Emmett-Teller measurement. The results indicate that the prepared samples have anatase and brookite phases. Additionally, Nd as Nd3+may enter into the lattice ofTiO2and the presence of Nd3+substantially enhances the photocatalytic activity ofTiO2under visible light. In order to further explore the mechanism of photocatalytic degradation of organic pollutant, photoluminescence spectrometer and scavenger addition method have been employed. It is found that hydroxide radicals produced by Nd-dopedTiO2under visible light are one of reactive species for Rh-B degradation and photogenerated electrons are mainly responsible for the formation of the reactive species.

FeYO3@rGO nanocomposites: Synthesis, characterization and application in photooxidative degradation of atrazine under visible light

2021 ◽  
Vol 11 (5) ◽  
pp. 706-716
Author(s):  
Nada D. Al-Khthami ◽  
Tariq Altalhi ◽  
Mohammed Alsawat ◽  
Mohamed S. Amin ◽  
Yousef G. Alghamdi ◽  
...  
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Bandgap Energy ◽  
X Ray Diffraction ◽  
X Ray ◽  
Transmission Electron ◽  
Reduced Graphene ◽  
Structural Surface ◽  
Adsorption Desorption

Different organic pollutants have been remediated photo catalytically by applying perovskite photocatalysts. Atrazine (ATR) is a pesticide commonly detected as a pollutant in drinking, surface and ground water. Herein, FeYO3@rGO heterojunction was synthesized and applied for photooxidation decomposition of ATR. First, FeYO 3nanoparticles (NPs) were prepared via routine sol-gel. After that, FeYO3 NPs were successfully incorporated with different percentages (5, 10, 15 and 20 wt.%) of reduced graphene oxide (rGO) in the synthesis of novel FeYO3@rGO photocatalyst. Morphological, structural, surface, optoelectrical and optical characteristics of constructed materials were identified via X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), Transmission electron microscopy (TEM), adsorption/desorption isotherms, diffusive reflectance (DR) spectra, and photoluminescence response (PL). Furthermore, photocatalytic achievement of the constructed materials was evaluated via photooxidative degradation of ATR. Various investigations affirmed the usefulness of rGO incorporation on the advancement of formed photocatalysts. Actually, novel nanocomposite containing rGO (15 wt.%) possessed diminished bandgap energy, as well as magnified visible light absorption. Furthermore, such nanocomposite presented exceptional photocatalytic achievement when exposed to visible light as ATR was perfectly photooxidized over finite amount (1.6 g · L-1) from the optimized photocatalyst when illuminated for 30 min. The advanced photocatalytic performance of constructed heterojunctions could be accredited mainly to depressed recombination amid induced charges. The constructed FeYO3@rGO nanocomposite is labelled as efficient photocatalyst for remediation of herbicides from aquatic environments.

Preparation of C, N and P co-doped TiO2 and its photocatalytic activity under visible light

2019 ◽  
Vol 12 (04) ◽  
pp. 1950045 ◽  
Author(s):  
Lin Zhao ◽  
Yanzhao Xie ◽  
Qiuyu Lin ◽  
Rongze Zheng ◽  
Yong Diao
Keyword(s):  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Soluble Starch ◽  
Doping Amount ◽  
X Ray ◽  
Composite Catalysts ◽  
One Step ◽  
Co Doped

A series of composite catalysts of C, N and P co-doped TiO2 were prepared by sol-gel method, using a biomass (soluble starch) dopant. The samples were characterized by field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectroscopy (DRS), fourier transform infrared (FTIR) spectroscopy. The results show that TiO2 is co-doped with C, N and P by one step. The resulting composite exhibited higher specific surface area, wider visible-light absorption band with respect to the pure TiO2. The sample calcined at 400∘C for 2[Formula: see text]h with a doping amount of 6[Formula: see text]g soluble starch showed the best electrochemical performance. The C, N and P co-doped TiO2 was also used for the degradation of methylene blue (MB) and degradation ratio was up to 98% in 80[Formula: see text]min under visible light irradiation.

scholarly journals Preparation of Ni Doped ZnO-TiO2Composites and Their Enhanced Photocatalytic Activity

2014 ◽  
Vol 2014 ◽  
pp. 1-8 ◽  
Author(s):  
Xiaowen Zou ◽  
Xiaoli Dong ◽  
Limei Wang ◽  
Hongchao Ma ◽  
Xinxin Zhang ◽  
...  
Keyword(s):  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
Visible Region ◽  
Hydroxyl Groups ◽  
X Ray ◽  
Surface Hydroxyl ◽  
Simulated Solar Light ◽  
Transmission Electron ◽  
Doped Zno

Herein, Ni doped ZnO-TiO2composites were prepared by facile sol-gel approach and were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-visible diffuse reflectance spectroscopy (UV-Vis DRS), X-ray photoelectron spectroscopy (XPS), and photoluminescence spectroscopy (PL). The results indicated that the Ni ions can be incorporated into the lattice of TiO2structure and replace Ti. The introduction of Ni expanded light absorption of TiO2to visible region, increased amount of surface hydroxyl groups and physically adsorbed oxygen (as the electronic scavenges), and then enhanced separation rate of photogenerated carriers. The photodegradation test of reactive brilliant blue (KN-R) under simulated solar light indicated that Ni doped ZnO-TiO2composites have better photocatalytic activities, as compared to those of TiO2and ZnO-TiO2.

scholarly journals Fabrication of ZnS-Bi-TiO2Composites and Investigation of Their Sunlight Photocatalytic Performance

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Xuewei Dong ◽  
Fan Zhang ◽  
Chuan Rong ◽  
Hongchao Ma
Keyword(s):  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Kinetic Constant ◽  
Sol Gel ◽  
Visible Region ◽  
Xenon Lamp ◽  
X Ray ◽  
Photodegradation Efficiency ◽  
Photogenerated Electrons ◽  
Transmission Electron

The ZnS-Bi-TiO2composites were prepared by the sol-gel method and were characterized by X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), X-ray diffraction (XRD) and UV-visible diffuse reflectance spectroscopy (UV-Vis DRS). It is found that the doped Bi as Bi4+/Bi3+species existed in composites, and the introducing of ZnS enhanced further the light absorption ability of TiO2in visible region and reduced the recombination of photogenerated electrons and holes. As compared to pure TiO2, the ZnS-Bi-TiO2exhibited enhanced photodegradation efficiency under xenon lamp irradiation, and the kinetic constant of methyl orange removal with ZnS-Bi-Ti-0.005 (0.0141 min−1) was 3.9 times greater than that of pure TiO2(0.0029 min−1), which could be attributed to the existence of Bi4+/Bi3+species, the ZnS/TiO2heterostructure.

scholarly journals Enhanced Visible Light Photocatalytic Activity of Mesoporous AnataseTiO2Codoped with Nitrogen and Chlorine

2012 ◽  
Vol 2012 ◽  
pp. 1-6 ◽  
Author(s):  
Xiuwen Cheng ◽  
Xiujuan Yu ◽  
Zipeng Xing ◽  
Lisha Yang
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Band Gap ◽  
Light Absorption ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Visible Region ◽  
X Ray ◽  
Visible Light Photocatalytic Activity ◽  
Visible Light Photocatalytic

Anatase mesoporous titanium dioxide codoped with nitrogen and chlorine (N-Cl-TiO2) photocatalysts were synthesized through simple one-step sol-gel reactions in the presence of ammonium chloride. The resulting materials were characterized by X-ray diffraction (XRD), transmission electron microscope (TEM), X-ray photoelectron spectroscopy (XPS), and ultraviolet-visible diffuse reflection spectrum (UV-vis DRS). XRD results indicated that codoping with nitrogen and chlorine could effectively retard the phase transformation of TiO2from anatase to rutile and the growth of the crystallite sizes. XPS revealed that nitrogen and chlorine elements were incorporated into the lattice of TiO2through substituting the lattice oxygen atoms. DRS exhibited that the light absorption of N-Cl-TiO2in visible region was greatly improved. As a result, the band gap of TiO2was reduced to 2.12 eV. The photocatalytic activity of the as-synthesized TiO2was evaluated for the degradation of RhB and phenol under visible light irradiation. It was found that N-Cl-TiO2catalyst exhibited higher visible light photocatalytic activity than that of P25 TiO2and N-TiO2, which was attributed to the small crystallite size, intense light absorption in visible region, and narrow band gap.

scholarly journals Improved Visible Light Photocatalytic Activity for TiO2Nanomaterials by Codoping with Zinc and Sulfur

2015 ◽  
Vol 2015 ◽  
pp. 1-8 ◽  
Author(s):  
Qianzhi Xu ◽  
Xiuying Wang ◽  
Xiaoli Dong ◽  
Chun Ma ◽  
Xiufang Zhang ◽  
...  
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance Spectroscopy ◽  
Sol Gel ◽  
X Ray Diffraction ◽  
Sunlight Irradiation ◽  
X Ray ◽  
Transmission Electron ◽  
Photoinduced Charge

S/Zn codoped TiO2nanomaterials were synthesized by a sol-gel method. X-ray diffraction, UV-vis diffuse reflectance spectroscopy, transmission electron microscopy, photoluminescence spectroscopy, and X-ray photoelectron spectroscopy were used to characterize the morphology, structure, and optical properties of the prepared samples. The introduction of Zn and S resulted in significant red shift of absorption edge for TiO2-based nanomaterials. The photocatalytic activity was evaluated by degrading reactive brilliant red X-3B solution under simulated sunlight irradiation. The results showed S/Zn codoped TiO2exhibited higher photocatalytic activity than pure TiO2and commercial P25, due to the photosynergistic effect of obvious visible light absorption, efficient separation of photoinduced charge carriers, and large surface area. Moreover, the content of Zn and S in the composites played important roles in photocatalytic activity of TiO2-based nanomaterials.

Molecularly Imprinted TiO2/WO3-Coated Magnetic Nanocomposite for Photocatalytic Degradation of 4-Nitrophenol Under Visible Light

2016 ◽  
Vol 69 (6) ◽  
pp. 638 ◽  
Author(s):  
Shoutai Wei ◽  
Hualong Liu ◽  
Chiyang He ◽  
Ying Liang
Keyword(s):  
Visible Light ◽  
Photocatalytic Degradation ◽  
Fe3o4 Nanoparticles ◽  
Photoelectron Spectroscopy ◽  
Sol Gel ◽  
Energy Resource ◽  
Precipitation Method ◽  
Adsorption Ability ◽  
Molecularly Imprinted ◽  
X Ray

In this paper, a molecularly imprinted TiO2/WO3-coated magnetic Fe3O4@SiO2 nanocomposite was developed for photocatalytic degradation. Fe3O4 nanoparticles were first prepared by a traditional co-precipitation method, and then a SiO2 shell was grown on the surface of the Fe3O4 nanoparticles. Finally, a 4-nitrophenol imprinted TiO2/WO3 coating was obtained on the surface of the Fe3O4@SiO2 nanocomposite via a sol-gel method and subsequent calcination. The new composite was characterised by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), high resolution TEM (HRTEM) and vibrating sample magnetometry (VSM). In addition, the adsorption ability and photocatalytic activity of the composite were investigated. Results showed that the imprinted composite had higher adsorption ability for the template than the non-imprinted composite. The imprinted catalyst could degrade 4-nitrophenol under visible light with a first-order reaction rate of 0.1039 h–1, which was ~2.5 times that of the non-imprinted catalyst. The new imprinted catalyst showed good catalytic selectivity, an ease of being recycled by an external magnetic field, good reusability, no need for additional chemicals, and allows the possibility of utilising solar light as energy resource. Therefore, the catalyst can be potentially applied for ‘green’, low-cost and effective degradation of 4-nitrophenol in real wastewater.

Preparation of BiXY(2-X)O3 and its Photocatalytic Degradation of Molasses Fermentation Wastewater under Visible-Light Irradiation

2011 ◽  
Vol 287-290 ◽  
pp. 1640-1645 ◽  
Author(s):  
Min Guang Fan ◽  
Zu Zeng Qin ◽  
Zi Li Liu ◽  
Tong Ming Su
Keyword(s):  
Photocatalytic Activity ◽  
Visible Light ◽  
Photocatalytic Degradation ◽  
Visible Light Irradiation ◽  
Photoelectron Spectroscopy ◽  
Diffuse Reflectance ◽  
Diffuse Reflectance Spectroscopy ◽  
Active Oxygen Species ◽  
Light Irradiation ◽  
X Ray

A series of BixY(2-x)O3photocatalysts were successfully prepared by a solid-state reaction and were subsequently characterized by powder X-ray diffraction, UV-vis diffuse reflectance spectroscopy, and X-ray photoelectron spectroscopy (XPS). The UV-vis diffuse reflectance spectra revealed that the BixY(2-x)O3samples absorbed light in the visible-light range (400-800 nm). The XPS results indicated that active oxygen species were generated on the Bi1.8Y0.2O3surface, which displayed a higher photocatalytic activity. When using photocatalytic degradation molasses fermentation wastewater as a model reaction, the Bi1.8Y0.2O3showed higher photocatalytic activity in comparison to Bi0.2Y1.8O3under visible-light irradiation.

Sign in / Sign up

Export Citation Format

Share Document