scholarly journals Stochastic BEM for the Vibroacoustic Analysis of Three-Dimensional Structures

2011 ◽  
Vol 2011 ◽  
pp. 1-12 ◽  
Author(s):  
R. D'Amico ◽  
A. Pratellesi ◽  
M. Pierini ◽  
N. Baldanzini

Nowadays, extending the NVH prediction reliability to the whole frequency range is an attractive goal of vibroacoustics. Deterministic methodologies are well established for the low-frequency range, but, decreasing the wavelength, energy-based methods are necessary. In such a range, a crucial role is played by small perturbations which highly influence the response sensitivity. Moreover, taking into account these variations allows to make the product design more robust and even quicker. Introducing geometrical uncertainties within the classic BEM formulation allows to obtain the so-called stochastic BEM. As a result, the solution shows deterministic behaviour at low frequencies; decreasing the wavelength, the effect of the uncertainties smooths the response. Consequently, it is possible to obtain an averaged trend over the whole frequency range which asymptotically tends to the deterministic one. In this paper, we deal with three-dimensional acoustic SBEM. First, the formulation and its basic assumptions are presented. Secondly, they are applied to academic cases to show its potentialities in predicting vibroacoustic behaviour over a wide frequency range.

1998 ◽  
Vol 80 (2) ◽  
pp. 680-695 ◽  
Author(s):  
Dora E. Angelaki

Angelaki, Dora E. Three-dimensional organization of otolith-ocular reflexes in rhesus monkeys. III. Responses to translation. J. Neurophysiol. 80: 680–695, 1998. The three-dimensional (3-D) properties of the translational vestibulo-ocular reflexes (translational VORs) during lateral and fore-aft oscillations in complete darkness were studied in rhesus monkeys at frequencies between 0.16 and 25 Hz. In addition, constant velocity off-vertical axis rotations extended the frequency range to 0.02 Hz. During lateral motion, horizontal responses were in phase with linear velocity in the frequency range of 2–10 Hz. At both lower and higher frequencies, phase lags were introduced. Torsional response phase changed more than 180° in the tested frequency range such that torsional eye movements, which could be regarded as compensatory to “an apparent roll tilt” at the lowest frequencies, became anticompensatory at all frequencies above ∼1 Hz. These results suggest two functionally different frequency bandwidths for the translational VORs. In the low-frequency spectrum (≪0.5 Hz), horizontal responses compensatory to translation are small and high-pass-filtered whereas torsional response sensitivity is relatively frequency independent. At higher frequencies however, both horizontal and torsional response sensitivity and phase exhibit a similar frequency dependence, suggesting a common role during head translation. During up-down motion, vertical responses were in phase with translational velocity at 3–5 Hz but phase leads progressively increased for lower frequencies (>90° at frequencies <0.2 Hz). No consistent dependence on static head orientation was observed for the vertical response components during up-down motion and the horizontal and torsional response components during lateral translation. The frequency response characteristics of the translational VORs were fitted by “periphery/brain stem” functions that related the linear acceleration input, transduced by primary otolith afferents, to the velocity signals providing the input to the velocity-to-position neural integrator and the oculomotor plant. The lowest-order, best-fit periphery/brain stem model that approximated the frequency dependence of the data consisted of a second order transfer function with two alternating poles (at 0.4 and 7.2 Hz) and zeros (at 0.035 and 3.4 Hz). In addition to clearly differentiator dynamics at low frequencies (less than ∼0.5 Hz), there was no frequency bandwidth where the periphery/brain stem function could be approximated by an integrator, as previously suggested. In this scheme, the oculomotor plant dynamics are assumed to perform the necessary high-frequency integration as required by the reflex. The detailed frequency dependence of the data could only be precisely described by higher order functions with nonminimum phase characteristics that preclude simple filtering of afferent inputs and might be suggestive of distributed spatiotemporal processing of otolith signals in the translational VORs.


2020 ◽  
Author(s):  
Deli SHI ◽  
Leiming FANG ◽  
Xiaoqiang Zhang ◽  
Jinlong TANG ◽  
Jun LI ◽  
...  

Abstract The Fe nanocrystals (NCs) were embedded into the epitaxial BaTiO 3 (BTO) matrix. According to optimize growth processes, a novel nanocomposite system was constructed, which consist of well epitaxial BTO layer and three-dimensional Fe NCs. Based on this, the different dielectric response in the regions of low temperature-high frequency and low frequency-high temperature were revealed by the contribution of hopping and interfacial polarizations, respectively. With the increased amount of Fe NCs, the obvious enhancement of low-frequency conductivity, middle frequency capacitance and high-frequency inductive effect was found. The metal NC embedding plays an important role in tuning the dielectric behaviors and ac conductivity of oxide dielectrics. This significant rectification effect in the wide-frequency ranges opens up a new direction for the designing of embedded nano-capacitors.


Geophysics ◽  
1992 ◽  
Vol 57 (6) ◽  
pp. 854-859 ◽  
Author(s):  
Xiao Ming Tang

A new technique for measuring elastic wave attenuation in the frequency range of 10–150 kHz consists of measuring low‐frequency waveforms using two cylindrical bars of the same material but of different lengths. The attenuation is obtained through two steps. In the first, the waveform measured within the shorter bar is propagated to the length of the longer bar, and the distortion of the waveform due to the dispersion effect of the cylindrical waveguide is compensated. The second step is the inversion for the attenuation or Q of the bar material by minimizing the difference between the waveform propagated from the shorter bar and the waveform measured within the longer bar. The waveform inversion is performed in the time domain, and the waveforms can be appropriately truncated to avoid multiple reflections due to the finite size of the (shorter) sample, allowing attenuation to be measured at long wavelengths or low frequencies. The frequency range in which this technique operates fills the gap between the resonant bar measurement (∼10 kHz) and ultrasonic measurement (∼100–1000 kHz). By using the technique, attenuation values in a PVC (a highly attenuative) material and in Sierra White granite were measured in the frequency range of 40–140 kHz. The obtained attenuation values for the two materials are found to be reliable and consistent.


2007 ◽  
Vol 38 (7) ◽  
pp. 11-17
Author(s):  
Ronald M. Aarts

Conventionally, the ultimate goal in loudspeaker design has been to obtain a flat frequency response over a specified frequency range. This can be achieved by carefully selecting the main loudspeaker parameters such as the enclosure volume, the cone diameter, the moving mass and the very crucial “force factor”. For loudspeakers in small cabinets the results of this design procedure appear to be quite inefficient, especially at low frequencies. This paper describes a new solution to this problem. It consists of the combination of a highly non-linear preprocessing of the audio signal and the use of a so called low-force-factor loudspeaker. This combination yields a strongly increased efficiency, at least over a limited frequency range, at the cost of a somewhat altered sound quality. An analytically tractable optimality criterion has been defined and has been verified by the design of an experimental loudspeaker. This has a much higher efficiency and a higher sensitivity than current low-frequency loudspeakers, while its cabinet can be much smaller.


2020 ◽  
Vol 635 ◽  
pp. A76 ◽  
Author(s):  
L. Bondonneau ◽  
J.-M. Grießmeier ◽  
G. Theureau ◽  
A. V. Bilous ◽  
V. I. Kondratiev ◽  
...  

Context. To date, only 69 pulsars have been identified with a detected pulsed radio emission below 100 MHz. A LOFAR-core LBA census and a dedicated campaign with the Nançay LOFAR station in stand-alone mode were carried out in the years 2014–2017 in order to extend the known population in this frequency range. Aims. In this paper, we aim to extend the sample of known radio pulsars at low frequencies and to produce a catalogue in the frequency range of 25–80 MHz. This will allow future studies to probe the local Galactic pulsar population, in addition to helping explain their emission mechanism, better characterising the low-frequency turnover in their spectra, and obtaining new information about the interstellar medium through the study of dispersion, scattering, and scintillation. Methods. We observed 102 pulsars that are known to emit radio pulses below 200 MHz and with declination above −30°. We used the Low Band Antennas (LBA) of the LOw Frequency ARray (LOFAR) international station FR606 at the Nançay Radio Observatory in stand-alone mode, recording data between 25 and 80 MHz. Results. Out of our sample of 102 pulsars, we detected 64. We confirmed the existence of ten pulsars detected below 100 MHz by the LOFAR LBA census for the first time (Bilous et al. 2020, A&A, 635, A75) and we added two more pulsars that had never before been detected in this frequency range. We provided average pulse profiles, DM values, and mean flux densities (or upper limits in the case of non-detections). The comparison with previously published results allows us to identify a hitherto unknown spectral turnover for five pulsars, confirming the expectation that spectral turnovers are a widespread phenomenon.


2020 ◽  
Vol 142 (7) ◽  
Author(s):  
M. Awasthi ◽  
J. Rowlands ◽  
D. J. Moreau ◽  
C. J. Doolan

Abstract Measurements of the wall pressure fluctuations near a wing-plate junction were made for wings with three different aspect ratios (AR) of 0.2, 0.5, and 1.0 at several angles of attack. The chord-based Reynolds number for each wing was 274,000. The results show that the wall pressure fluctuations are a function of wing AR for cases where AR≤ 1.0. For each wing, the pressure fluctuations are highest upstream of the wing leading-edge due to three-dimensional flow separation; wings with AR = 1.0 and 0.5 show comparable levels, while those with AR = 0.2 show lower fluctuation levels over a wide frequency range. Downstream of the leading-edge, the pressure fluctuations decay rapidly on both sides of the wing until the maximum thickness location after which little variation is observed. The pressure fluctuations downstream of the leading-edge on the suction-side were observed to be comparable for AR = 0.2 and 0.5, while those for AR = 1.0 were higher in magnitude. On the pressure-side, the pressure fluctuations near the leading-edge are a weak function of AR; however, those further downstream remain independent of AR. The pressure fluctuations aft of the wing on the suction-side are more coherent for lower ARs and show higher convection velocity, possibly due to an interaction between the tip and the junction flows for lower ARs.


Author(s):  
Sophie R. Kaye ◽  
Ethan D. Casavant ◽  
Paul E. Slaboch

Abstract Attenuating low frequencies is often problematic, due to the large space required for common absorptive materials to mitigate such noise. However, natural hollow reeds are known to effectively attenuate low frequencies while occupying relatively little space compared to traditional absorptive materials. This paper discusses the effect of varied outer diameter, and outer spacing on the 200–1600 Hz acoustic absorption of additively manufactured arrays of hollow cylinders. Samples were tested in a 10 cm diameter normal incidence impedance tube such that cylinder length was oriented perpendicular to the incoming plane wave. By varying only one geometric element of each array, the absorption due to any particular parameter can be assessed individually. The tests confirmed the hypothesis that minimizing cylinder spacing and maximizing cylinder diameter resulted in increased overall absorption and produced more focused absorption peaks at specific low frequencies. Wider cylinder spacing produced a broader absorptive frequency range, despite shifting upward in frequency. Thus, manipulating these variables can specifically target absorption for low frequency noise that would otherwise disturb listeners.


Author(s):  
B. Dong ◽  
J. L. Han

AbstractThe Five-hundred-metre Aperture Spherical Telescope (FAST) is being constructed in China. With an illuminated aperture of 300-m diameter, it will be the most sensitive single-dish radio telescope in the world. We calculate the beam patterns, gains, and efficiencies of the FAST at 200 MHz, 1.4 GHz, and 3 GHz. A program is developed to calculate the structural parameters and construct the FAST models. The three-dimensional beam patterns are calculated by utilising the shooting and bouncing ray method. We show that, with a coaxial horn feed, the FAST has a beam pattern of high gain and reasonably low first sidelobe over the frequency range of 200 MHz to 3 GHz. Compared with an ideal 300-m parabolic reflector, the un-illuminated spherical part of the FAST would make the power level near both sides of the main beam rise by at least 20 dB and the efficiency tends to decrease at high frequencies. At a zenith angle of 0°, its efficiencies at 200 MHz, 1.4 GHz, and 3 GHz are 71.72%, 66.94%, and 57.55%, respectively. We conclude that the FAST is an excellent telescope at low frequencies. At high frequencies, the triangular spherical panels and the gaps between panels are important factors that affect the performance of the FAST.


The vibrational absorption spectra of some substituted benzenes have been measured in the range 50 to 450 cm -1 . The compounds were measured as liquids, in solutions, as crystalline solidsat low temperature, and in polyethylene matrices. The extension of the infrared spectrum to very low frequencies has made it possible to determine new values for many fundamental vibrations. An assignment of all the vibrational frequencies in the low-frequency range has been made, from the infrared and Raman data, for p -dihalogeno-benzenes, p -halogenotoluenes, p -halogeno-nitrobenzenes, and for some mono-substituted benzenes. Some measurements have been made on the marked variation of intensity of the lowest frequency bending mode of p -dihalogeno-benzenes.


Sign in / Sign up

Export Citation Format

Share Document