scholarly journals Electrodeposition and Characterization of Nanocrystalline Ni-Fe Alloys

2011 ◽  
Vol 2011 ◽  
pp. 1-8 ◽  
Author(s):  
R. Abdel-Karim ◽  
Y. Reda ◽  
M. Muhammed ◽  
S. El-Raghy ◽  
M. Shoeib ◽  
...  
Keyword(s):  
Grain Size ◽  
Surface Morphology ◽  
Iron Content ◽  
Mass Ratio ◽  
Grain Sizes ◽  
Maximum Value ◽  
Average Grain Size ◽  
Fe Alloys ◽  
Short Time

Nanocrystalline Ni-Fe deposits with different composition and grain sizes were fabricated by electrodeposition. Deposits with iron contents in the range from 7 to 31% were obtained by changing the Ni2+/Fe2+mass ratio in the electrolyte. The deposits were found to be nanocrystalline with average grain size in the range 20–30 nm. The surface morphology was found to be dependent on Ni2+/Fe2+mass ratio as well as electroplating time. The grains size decreased with increasing the iron content, especially in case of short time electroplating. Increasing the electroplating time had no significant effect on grain size. The microhardness of the materials followed the regular Hall-Petch relationship with a maximum value (762 Hv) when applying Ni2+/Fe2+mass ratio equal to 9.8.

Preparation and Characterization of Transparent Nanocrystalline Ceramics

2008 ◽  
Vol 368-372 ◽  
pp. 402-406 ◽  
Author(s):  
Tie Cheng Lu ◽  
Xiang Hui Chang ◽  
Jie Zhang ◽  
Jian Qi Qi ◽  
Xiang Jie Luo
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
High Pressure ◽  
Low Cost ◽  
Nanocrystalline Ceramics ◽  
Grain Sizes ◽  
Average Grain Size ◽  
Sintering Characteristics ◽  
Sintering Condition

The transparent nanocrystalline MgAl2O4 spinel ceramics were synthesized at lowtemperature and high-pressure conditions with low-cost nano-sized MgAl2O4 powder. The sintering characteristics of transparent nano-ceramics were investigated at 500~700oC under 2 ~ 5 GPa. The optimal sintering condition for preparing transparent nano-ceramics was determined. The microstructure and phase composition of powder, as well as the microstructures, morphologies, optical properties, densities and mechanical properties of synthetic ceramics were investigated. The grain sizes of the synthetic ceramics are less than 100 nm, far smaller than those of usual transparent micron-ceramics, and the average grain size depends on the pressure and temperature. The transmittance at the saturation plateau can near 80%. The relative densities of all samples are less than 99%, however, they are highly transparent. The toughness, derived from energy dissipation, of the transparent nano-ceramics was investigated and was compared with that of transparent micron-ceramic.

Analysis and Characterization of Solid and Liquid Organic Fertilizer from Hydrothermal Carbonization (HTC) of Chicken Feather and Blood Waste

2021 ◽  
Vol 21 (3) ◽  
pp. 651
Author(s):  
Agus Kuncaka ◽  
Rizky Ibnufaatih Arvianto ◽  
Almas Shafira Ramadhanty Bunga Latifa ◽  
Munawir Ramadhan Rambe ◽  
Adhitasari Suratman ◽  
...  
Keyword(s):  
Iron Content ◽  
Solid Phase ◽  
Organic Fertilizer ◽  
Liquid Product ◽  
Hydrothermal Carbonization ◽  
Mass Ratio ◽  
Solid Product ◽  
Chicken Waste ◽  
20 Nm

Conversion of feather and blood from chicken slaughterhouse waste for producing solid and liquid organic fertilizer excluding composting process with a variation of the mass ratio of feather and blood of a chicken has been conducted. The nitrogen, sulfur, and iron content in the solid and liquid product of the hydrothermal carbonization process were analyzed to identify and characterize the possibility of hydrolysate as a source of nitrogen, sulfur, and iron in soil fertilizer. Feather and blood of chicken waste were introduced to a hydrothermal carbonization reactor with the addition of limestone at a temperature range of 160–170 °C for the preparation of solid and liquid organic fertilizer. According to the FTIR interpretation, the solid product had functional groups such as NH, OH, CH sp3, SH, C=O, C=C, C–O–C, and C–H aromatic. The nitrogen, sulfur, and iron content of the optimal ratio in the solid phase were 4.67%, 1.63%, and 3694.56 ppm, while their contents in the liquid fertilizer were 3.76%, 1.80%, and 221.56 ppm, respectively. The vibration of 478 cm–1 is attributed to Fe–O paramagnetic (Fe2O3) confirmed by TEM images showed the diameter size less than 20 nm indicating the presence of superparamagnetic material.

scholarly journals Characterization of glacial silt and clay using automated mineralogy

2019 ◽  
Vol 60 (80) ◽  
pp. 49-65
Author(s):  
Jeff W. Crompton ◽  
Gwenn E. Flowers ◽  
Brendan Dyck
Keyword(s):  
Grain Size ◽  
Size Composition ◽  
Rock Properties ◽  
Fine Grained ◽  
Rock Fragments ◽  
Grain Sizes ◽  
Automated Mineralogy ◽  
Log Normal ◽  
Discrete Populations

AbstractGlacial erosion produces vast quantities of fine-grained sediment that has a far-reaching impact on Earth surface processes. To gain a better understanding of the production of glacial silt and clay, we use automated mineralogy to quantify the microstructure and mineralogy of rock and sediment samples from 20 basins in the St. Elias Mountains, Yukon, Canada. Sediments were collected from proglacial streams, while rock samples were collected from ice marginal outcrops and fragmented using electrical pulse disaggregation. For both rock fragments and sediments, we observe a log-normal distribution of grain sizes and a sub-micrometer terminal grain size. We find that the abrasion of silt and clay results in both rounding and the exploitation of through-going fractures. The abundance of inter- versus intragranular fractures depends on mineralogy and size. Unlike the relatively larger grains, where crushing and abrasion are thought to exploit and produce discrete populations of grain sizes, the comminution of fines leads to a grain size, composition and rounding that is continuously distributed across size, and highly dependent on source-rock properties.

Effect of Annealing on Nanocrystalline Structure of Nb3Sn Diffusion Layers in Composites with Internal Tin Sources

2010 ◽  
Vol 297-301 ◽  
pp. 126-131 ◽  
Author(s):  
E.N. Popova ◽  
Vladimir V. Popov ◽  
E.P. Romanov ◽  
S.V. Sudareva ◽  
L.V. Elohina ◽  
...  
Keyword(s):  
Grain Size ◽  
Carrying Capacity ◽  
Nanocrystalline Structure ◽  
Diffusion Annealing ◽  
External Diameter ◽  
High Temperature Annealing ◽  
Grain Sizes ◽  
Diffusion Layers ◽  
Average Grain Size ◽  
Complete Transformation

Multifilamentary Nb3Sn-based superconducting composites manufactured by an internal-tin method have been studied by transmission (TEM) and scanning (SEM) electron microscopy. The main goal of this study is to reveal the effect of diffusion annealing regimes as well as the external diameter of the wires on the structure of nanocrystalline Nb3Sn layers (average grain size, grain size distribution, layer thickness, amount of Sn, etc.). It is demonstrated that multistep diffusion annealing results in quite a complete transformation of Nb filaments into Nb3Sn though some amount of the residual Nb remains in the filaments center. With an external diameter decrease the superconducting layers structure has been found to refine and get somewhat more uniform. An additional high-temperature annealing results in marked growth of Nb3Sn grain sizes and their scattering in sizes, which may negatively affect the current-carrying capacity of a wire.

Characterization of Defect Nucleation and Propagation in Fe2O3+FCC-Al Nanocomposites During Uniaxial Tensile and Compressive Deformations

2006 ◽  
Author(s):  
Vikas Tomar ◽  
Min Zhou
Keyword(s):  
Molecular Dynamics ◽  
Grain Size ◽  
Defect Formation ◽  
Voronoi Tessellation ◽  
Orientation Distribution ◽  
Uniaxial Tensile ◽  
Grain Sizes ◽  
Classical Molecular Dynamics ◽  
Average Grain Size ◽  
Nanocrystalline Structures

The objective of this research is to analyze uniaxial tensile and compressive mechanical deformations of α-Fe2O3 + fcc Al nanoceramic-metal composites using classical molecular dynamics (MD). Specifically, variations in the nucleation and the propagation of defects (such as dislocations and stacking faults etc.) with variation in the nanocomposite phase morphology and their effect on observed tensile and compressive strengths of the nanocomposites are analyzed. For this purpose, a classical molecular dynamics (MD) potential that includes an embedded atom method (EAM) cluster functional, a Morse type pair function, and a second order electrostatic interaction function is developed, see Tomar and Zhou (2004) and Tomar and Zhou (2006b). The nanocrystalline structures (nanocrystalline Al, nanocrystalline Fe2O3 and the nanocomposites with 40% and 60% Al by volume) with average grain sizes of 3.9 nm, 4.7 nm, and 7.2 nm are generated using a combination of the well established Voronoi tessellation method with the Inverse Monte-Carlo method to conform to prescribed log-normal grain size distributions. For comparison purposes, nanocrystalline structures with a specific average grain size have the same grain morphologies and the same grain orientation distribution. MD simulations are performed at the room temperature (300 K). Calculations show that the deformation mechanism is affected by a combination of factors including the fraction of grain boundary (GB) atoms and the electrostatic forces between atoms. The significance of each factor is dependent on the volume fractions of the Al and Fe2O3 phases. Depending on the relative orientations of the two phases at an interface, the contribution of the interface to the defect formation varies. The interfaces have stronger effect in structures with smaller average grain sizes than in structures with larger average grain sizes.

SIMS/AEM Characterization of Banded Microstructures in an Ni-Cr-Fe Alloy

1999 ◽  
Vol 5 (S2) ◽  
pp. 862-863 ◽  
Author(s):  
M.G. Burke ◽  
B.Z. Hyatt ◽  
G. McMahon
Keyword(s):  
Aging Temperature ◽  
Single Phase ◽  
Alloy 600 ◽  
Solution Annealing ◽  
Grain Sizes ◽  
Treated Condition ◽  
Alloy 690 ◽  
Fe Alloys ◽  
Thermally Treated

Ni-Cr-Fe alloys such as Alloy 600 and Alloy 690 are single phase fee alloys with excellent resistance to corrosion. Alloy 600 is generally used in a thermally-treated condition which is characterized by the intergranular precipitation of Cr-rich M7C3 and, depending upon the aging temperature, Cr-rich M23C6. These alloys are usually cast and processed by rolling or forging. These alloys can exhibit microstructures in which there are nonuniform distributions of intragranular carbides that appear as bands aligned parallel to the working direction (i.e. longitudinal) of the material. It is also possible for these materials to exhibit duplex grain sizes which can be associated with the banded carbide structure. Banded microstructures can become more prominent after further anneals. The resistance of the carbide bands to dissolution during solution annealing at temperatures up to 1150°C has prompted the further evaluation of banding in Alloy 600, specifically in terms of identifying those elements associated with the carbide bands.

Nanostructure Evolution of ZnO in Ultra-fast Microwave Sintering

2011 ◽  
Vol 691 ◽  
pp. 65-71 ◽  
Author(s):  
Rodolfo F. K. Gunnewiek ◽  
Ruth Herta Goldsmith Aliaga Kiminami
Keyword(s):  
Grain Size ◽  
Zinc Oxide ◽  
Grain Growth ◽  
Microwave Sintering ◽  
High Heating Rate ◽  
Heating Rates ◽  
Grain Sizes ◽  
Average Grain Size ◽  
Conventional Sintering ◽  
Holding Temperature

Grain growth is inevitable in the sintering of pure nanopowder zinc oxide. Sintering depend on diffusion kinetics, thus this growth could be controlled by ultra-fast sintering techniques, as microwave sintering. The purpose of this work was to investigate the nanostructural evolution of zinc oxide nanopowder compacts (average grain size of 80 nm) subjected to ultra-rapid microwave sintering at a constant holding temperature of 900°C, applying different heating rates and temperature holding times. Fine dense microstructures were obtained, with controlled grain growth (grain size from 200 to 450nm at high heating rate) when compared to those obtained by conventional sintering (grain size around 1.13µm), which leads to excessively large average final grain sizes.

Dielectric Properties of Nanograined BaTiO3 Ceramics Fabricated by Aerosol Deposition Method

2011 ◽  
Vol 485 ◽  
pp. 183-186 ◽  
Author(s):  
Tsutomu Furuta ◽  
Saki Hatta ◽  
Yoichi Kigoshi ◽  
Takuya Hoshina ◽  
Hiroaki Takeda ◽  
...  
Keyword(s):  
Grain Size ◽  
Room Temperature ◽  
Annealing Treatment ◽  
Aerosol Deposition ◽  
Dielectric Measurement ◽  
Deposition Method ◽  
Grain Sizes ◽  
Average Grain Size ◽  
Aerosol Deposition Method ◽  
Polarization Electric Field

Freestanding BaTiO3 ceramics films were fabricated using the aerosol deposition (AD) method and the size effect of nanograined BaTiO3 ceramics was demonstrated. Dense BaTiO3 thick film fabricated by the AD method was crystallized and detached from substrate by an annealing treatment at 600 °C, and then the grain size was controlled by a reannealing treatment at various temperatures. As a result, freestanding BaTiO3 thick films with various grain sizes from 24 to 170 nm were successfully obtained. Polarization–electric field (P–E) measurement revealed that BaTiO3 ceramics with grain sizes of more than 58 nm showed ferroelectricity, whereas BaTiO3 ceramics with an average grain size of 24 nm showed paraelectricity at room temperature. Dielectric measurement indicated that the permittivity decreased with decreasing grain size in the range of 170 to 24 nm.

Synthesis and Characterization of Plasma Synthesized Nanostructured Magnesia-Yttria Based Nanocomposites

2007 ◽  
Vol 1056 ◽  
Author(s):  
Jafar F. Al-Sharab ◽  
Rajendra Sadangi ◽  
Vijay Shukla ◽  
Bernard Kear
Keyword(s):  
Electron Microscopy ◽  
Transmission Electron Microscopy ◽  
Grain Size ◽  
Chemical Mapping ◽  
X Ray Diffraction ◽  
Fine Grained ◽  
Transmission Electron ◽  
Spray Method ◽  
Average Grain Size

ABSTRACTPolycrystalline Y2O3 is the material of choice for IR windows since it has excellent optical properties in the visible, and near infra-red band. However, current processing methods yield polycrystalline Y2O3 with large grain size (> 100 μm), which limits the hardness and erosion resistance attainable. One way to improve strength is to develop an ultra-fine grained material with acceptable optical transmission properties. To realize a fine-grained ceramic, one approach is to develop a composite structure, in which one phase inhibits the growth of the other phase during processing. In this study, Y2O3-MgO nanocomposite with various MgO content (20, 50 and 80 mol%) were synthesized using plasma spray method. Extensive characterization techniques including x-ray diffraction, scanning electron microscopy (SEM), Transmission electron microscopy (TEM) and Energy Dispersive spectrometry (EDS) were employed to study the synthesized powder as well as the consolidated sample. Transmission Electron Microscopy, as well as EDS chemical mapping, revealed that the consolidated sample have bi-continuous MgO-Y2O3 nanostructure with an average grain size of 200 nm.

Preparation and Characterization of As-Cast and Hot-Rolled Mg-5Al-0.3Mn-1Ce Alloy

2011 ◽  
Vol 284-286 ◽  
pp. 1559-1563 ◽  
Author(s):  
Jian Li Wang ◽  
Jian Ping Li ◽  
Li Min Wang ◽  
Li Dong Wang
Keyword(s):  
Grain Size ◽  
Test Results ◽  
Casting Method ◽  
Rolled Sample ◽  
Cast Sample ◽  
Average Grain Size ◽  
Dislocation Strengthening ◽  
Hot Rolled ◽  
Mould Casting

Mg-5Al-0.3Mn-1Ce alloy was prepared by metal mould casting method. The as-cast ingot was homogenized and hot-rolled with total thickness reduction of 61% after four passes. Texture, microstructure and mechanical properties of the studied alloy were investigated. Results showed that the as-cast sample was mainly composed of a-Mg, Mg17Al12and Al11Ce3phases. Average grain size of the as-cast sample was about 500 μm. After hot-rolling, average grain size was greatly refined to about 20 μm. Further more, the long acicular Al11Ce3phase was smashed to small pieces. Tensile test results demonstrated that ultimate tensile strength and yield strength of the hot-rolled sample were improved by 65.2% and 165% respectively compared with those of the as-cast sample. Strength enhancement was attributed to grain refining strengthening and dislocation strengthening mechanisms.

Sign in / Sign up

Export Citation Format

Share Document