scholarly journals PVC-Membrane Potentiometric Electrochemical Sensor Based on 2-(4-Oxopentan-2-ylideneamino)isoindoline-1,3-dione for Selective Determination of Holmium(III)

2011 ◽  
Vol 8 (s1) ◽  
pp. S97-S104 ◽  
Author(s):  
Hassan Ali Zamani
Keyword(s):  
Heavy Metal Ions ◽  
Alkaline Earth ◽  
Fast Response ◽  
Pvc Membrane ◽  
Indicator Electrode ◽  
Selective Determination ◽  
Nernstian Slope ◽  
Neutral Ionophore ◽  
Ph Range

2-(4-Oxopentan-2-ylideneamino) isoindoline-1,3-dione (OID) was found to be a suitable neutral ionophore in the fabrication of a highly selective Ho3+membrane sensor. The electrode has a near-Nernstian slope of 19.6±0.5 mV per decade with a wide concentration range between 1.0×10-6and 1.0×10-2mol/L in the pH range of 3.5–8.8, having a fast response time (∼5 s) and a detection limit of 5.8×10-7mol/L. This electrode presented very good selectivity and sensitivity towards the Ho3+ions over a wide variety of cations, including alkali, alkaline earth, transition and heavy metal ions. The practical utility of the electrode has been demonstrated by its use as an indicator electrode for the potentiometric titration of a Ho3+solution with EDTA and for the determination of Ho3+ions concentration in mixtures of two and three different ions.

scholarly journals Construction of Tb3+ PVC-MembraneElectrode Based on N,N’-Bis(pyrrolylmethylene)-2-aminobenzylamine

2011 ◽  
Vol 8 (s1) ◽  
pp. S203-S210 ◽  
Author(s):  
Hassan Ali Zamani ◽  
Zynab Rafati ◽  
Soraia Meghdadi
Keyword(s):  
Heavy Metal Ions ◽  
Alkaline Earth ◽  
Pvc Membrane ◽  
Indicator Electrode ◽  
Fluoride Ion ◽  
Solution Ph ◽  
Potentiometric Response ◽  
Nernstian Slope ◽  
Mouth Wash

In this work, we report as new Tb3+-PVC membrane sensor based onN,N’-bis(pyrrolylmethylene)- 2-aminobenzylamine (PMA) as a suitable ion carrier. Poly vinylchloride (PVC)-based membrane composed of PMA with oleic acid (OA) as anionic additives and acetophenone (AP) as plasticizing solvent mediators. The Tb3+sensor exhibits a Nernstian slope of 19.7±0.4 mV per decade over the concentration range of 1.0×10-5to 1.0×10-2M and a detection limit of 4.6×10-6M of Tb3+ions. The potentiometric response of the sensor is independent of the solution pH in the range of 2.9–8.1. It has a very short response time, in the whole concentration range (∼5 s). The recommended sensor revealed comparatively good selectivity with respect to most alkali, alkaline earth, some transition and heavy metal ions. It was successfully employed as an indicator electrode in the potentiometric titration of Tb(III) ions with EDTA. The electrode was also employed for the determination of the fluoride ion in two mouth wash preparations and the determination of Tb3+ions concentration in mixtures of three different ions.

Dysprosium(III) Ion-Selective Electrochemical Sensor Based on 6-Hydrazino-1,5-diphenyl-6,7-dihydropyrazolo[3,4-d]pyrimidine-4(5H)-imine

2007 ◽  
Vol 72 (9) ◽  
pp. 1189-1206 ◽  
Author(s):  
Hassan Ali Zamani ◽  
Mohammad Reza Ganjali ◽  
Nasim Seifi
Keyword(s):  
Heavy Metal Ions ◽  
Alkaline Earth ◽  
Fast Response ◽  
Sensor Response ◽  
Indicator Electrode ◽  
Selective Electrode ◽  
Membrane Sensor ◽  
Sensing Material ◽  
Ph Range

A Dy(III) ion-selective electrode based on 6-hydrazino-1,5-diphenyl-6,7-dihydropyrazolo[3,4-d]pyrimidine-4(5H)-imine (HDDPI) as an excellent sensing material was developed. The sensor exhibits a Nernstian behavior (a slope of 19.6 ± 0.3 mV per decade) over a wide concentration range (from 1.0 × 10-1 to 8.0 × 10-7 M Dy) with a detection limit of 4.2 × 10-7 M. The sensor response is independent of pH of the solution in the pH range 3.5-8.3. The sensor possesses the advantages of short conditioning time, fast response time (<10 s) and in particular, good selectivity and sensitivity to the dysprosium ion in the presence of a variety of cations, including alkali, alkaline earth, transition and heavy metal ions. The sensor also showed a great enhancement in selectivity coefficients for dysprosium ions, in comparison with the formerly mentioned dysprosium sensors. The electrode can be used for at least 10 weeks without any considerable divergence in the potentials. The proposed electrode was successfully used as an indicator electrode in potentiometric titration of Dy(III) ions with EDTA. The membrane sensor was also used in the determination of concentration of F- ions in some mouth washing solutions and in the Dy3+ recovery from solution.

scholarly journals Neodymium(III) PVC Membrane Electrodchemical Sensor Based on N-benzoylethylidene-2-aminobenzylamine

2012 ◽  
Vol 9 (4) ◽  
pp. 1941-1950 ◽  
Author(s):  
Hassan Ali Zamani ◽  
Mojdeh Zaferoni ◽  
Soraia Meghdadi
Keyword(s):  
Alkaline Earth ◽  
High Selectivity ◽  
Pvc Membrane ◽  
Indicator Electrode ◽  
Solution Ph ◽  
Response Characteristics ◽  
Potentiometric Response ◽  
Nernstian Slope ◽  
Mouth Wash

The N-benzoylethylidene-2-aminobenzylamine (BEA) was used as a suitable ionophore in construction of neodymium ion selective electrode. The electrode with composition of 30% PVC, 58% solvent mediator (NB), 2% ionophore (BEA) and 10% anionic additive (OA) shows the best potentiometric response characteristics. The Nd3+sensor exhibits a Nernstian slope of 21.2 ± 0.2 mV decade-1over the concentration range of 1.0 × 10-6to 1.0 × 10-2mol L-1, and a detection limit of 6.3 × 10-7mol L-1of Nd3+ions. The potentiometric response of the sensor is independent of the solution pH in the range of 2.4–8.5. It has a very short response time, in the whole concentration range (~7 s), and can be used for at least eight weeks. The proposed sensor revealed high selectivity with respect to all common alkali, alkaline earth, transition and heavy metal ions, including members of the lanthanide family other than Nd3+. The Nd3+sensor was successfully applied as an indicator electrode in the potentiometric titration of Nd3+ions with EDTA. The electrode was also employed for the determination of the fluoride ion in two mouth wash preparations.

scholarly journals Determination of Nd3+Ions in Solution Samples by a Coated Wire Ion-Selective Sensor

2012 ◽  
Vol 9 (1) ◽  
pp. 83-88 ◽  
Author(s):  
Hassan Ali Zamani
Keyword(s):  
High Selectivity ◽  
Water Solution ◽  
Fast Response ◽  
Indicator Electrode ◽  
Coated Wire ◽  
Nernstian Slope ◽  
Ph Range ◽  
Coated Wire Electrode ◽  
Selective Sensor

A new coated wire electrode (CWE) using 5-(methylsulfanyl)-3-phenyl-1H-1,2,4-triazole (MPT) as an ionophore has been developed as a neodymium ion-selective sensor. The sensor exhibits Nernstian response for the Nd3+ions in the concentration range of 1.0×10−6-1.0×10−2M with detection limit of 3.7×10−7M. It displays a Nernstian slope of 20.2±0.2 mV/decade in the pH range of 2.7–8.1. The proposed sensor also exhibits a fast response time of ∼5 s. The sensor revealed high selectivity with respect to all common alkali, alkaline earth, transition and heavy metal ions, including members of the lanthanide family other than Nd3+. The electrode was used as an indicator electrode in the potentiometric titration of Nd(III) ions with EDTA. The electrode was also employed for the determination of the Nd3+ions concentration in water solution samples.

scholarly journals Construction of Eu3+Ion-Selective Electrode Based on 1,2-Diaminopropane-N,N,N',N'-tetraacetic acid

2011 ◽  
Vol 8 (s1) ◽  
pp. S467-S473 ◽  
Author(s):  
Mohammad Reza Abedi ◽  
Hassan Ali Zamani
Keyword(s):  
Alkaline Earth ◽  
Dynamic Range ◽  
Pvc Membrane ◽  
Membrane Electrode ◽  
Tetraacetic Acid ◽  
Pvc Membrane Electrode ◽  
Nernstian Slope ◽  
Wide Linear Dynamic Range ◽  
Ph Range

A new Eu3+PVC membrane electrode based on 1,2-diaminopropane-N, N,N',N'-tetraacetic acid (DAPTA) as a suitable ionophore has been prepared and studied. The electrode shows a good selectivity for Eu(III) ion with respect to most common cations including alkali, alkaline earth, transition and heavy metal ions. This electrode has a wide linear dynamic range from 1.0×10-6to 1.0×10-2M with a Nernstian slope of 19.7±0.5 mV per decade and a low detection limit of 7.2×10-7M in the pH range of 2.5–9.1, while the response time was rapid (<10 s). The practical utility of the electrodes has been demonstratedby their use as indicator electrodes in the potentiometric titration of Eu3+ions with EDTA and for the determination of Eu3+in some water sample solutions.

New Polymeric Membrane Sensor Doped with N,N’-Bis(benzoin)-1,2-Phenylenediamine for Selective Determination of Aluminum

2012 ◽  
Vol 466-467 ◽  
pp. 336-341 ◽  
Author(s):  
Xin Lu Liu ◽  
Bin Xie ◽  
Xun Hai Pan ◽  
Kang Quan Qiao ◽  
Ying Wang
Keyword(s):  
Fast Response ◽  
Polymeric Membrane ◽  
Indicator Electrode ◽  
Response Mechanism ◽  
Neutral Carrier ◽  
Membrane Sensor ◽  
Selective Determination ◽  
Impedance Technique ◽  
Ph Range

A new polymeric membrane sensor for Al3+based on bis(benzoin)-1,2-phenylenediamine as a neutral carrier was investigated. The proposed sensor exhibits a near-Nernstian response for Al3+over a wide linear range of 3.0×10-7to 1.0×10-1mol/L, with a detection limit of 1.0×10-7mol/L and a slope of 19.7±0.3 mV/decade. The sensor displays a good selectivity toward Al3+over other cations in pH range of 2.5 to 4.0. It has relatively fast response time (8 s) and can be used at least for 3 months without considerable divergence in potential. The response mechanism was discussed in view of the A.C. impedance technique. It was successfully used as an indicator electrode in the determination of aluminum in real samples.

scholarly journals A lutetium pvc membrane sensor based on (2-oxo-1,2-diphenylethylidene)-n-phenylhydrazinecarbothioamide

2011 ◽  
Vol 76 (9) ◽  
pp. 1295-1305 ◽  
Author(s):  
Hassan Ali ◽  
Reza Ganjali ◽  
Farnoush Faridbod
Keyword(s):  
Alkaline Earth ◽  
High Sensitivity ◽  
Lanthanide Ions ◽  
Pvc Membrane ◽  
Indicator Electrode ◽  
Short Response Time ◽  
Membrane Sensor ◽  
Nernstian Slope ◽  
Ph Range ◽  
Pvc Membrane Sensor

Based on the former experience on the design and construction of metal ions sensors, especially those of high sensitivity for lanthanides, (2-oxo-1,2-diphenylethylidene)-N-phenylhydrazinecarbothioamide (PHCT) was used to construct a Lu3+ PVC sensor exhibiting a Nernstian slope of 19.8?0.3 mV decade-1. The sensor was found to function well over a concentration range of 1.0?10-2 and 1.0?10-6 mol L-1 of the target ion with a detection limit of 6.8?10-7 mol L-1. The sensor selectivity against many common alkaline, alkaline earth, transition, heavy metals and specially lanthanide ions was very good and it functioned well in the pH range 2.5 - 8.7. Having a lifetime of at least 2 months and a short response time of ?5 s, the sensor was successfully used as an indicator electrode in the potentiometric titration of Lu3+ ions.

scholarly journals Synthesis of a New Calix[4]Arene and Its Application in Construction of a Highly Selective Silver Ion-Selective Membrane Electrode

2009 ◽  
Vol 2009 ◽  
pp. 1-5 ◽  
Author(s):  
Saeed Taghvaei-Ganjali ◽  
Reza Zadmard ◽  
Masoumeh Zeyaei ◽  
Kabeh Rahnama ◽  
Farnoush Faridbod ◽  
...  
Keyword(s):  
Response Time ◽  
Potentiometric Titration ◽  
Fast Response ◽  
Pvc Membrane ◽  
Indicator Electrode ◽  
Membrane Electrode ◽  
Membrane Sensor ◽  
Selective Membrane ◽  
Ph Range ◽  
Pvc Membrane Sensor

A PVC membrane sensor for Ag (I) ions has been prepared. The membrane has 5, 11, 17, 23-tetra-tert-butyl-25-(3-N, N-diethyldithio carbamoylpropoxy)-26,27,28-tris-propoxy calix[4]arene (CAD) as a carrier. It was found that the sensor exhibits a Nernstian response for Ag+ ions over a wide concentration range (10−2–10−6 M). Additionally, it illustrates a fast response time (about 5 seconds), and it can be used for at least 2 months without any considerable divergence in potentials. The nature of the plasticizer, the additive, the concentration of internal solutions in the electrodes, and the composition of the membrane were investigated. Furthermore, the suggested membrane electrode revealed good selectivities for Ag+ over a variety of other metal cations, and it could be used in the pH range of 3.0–7.0. Eventually, it was successfully applied as an indicator electrode for the potentiometric titration of Ag+ ion with NaCl.

scholarly journals Mefenamic Acid Selective Membranes Sensor and Its Application to pharmaceutical Analysis

2016 ◽  
Vol 13 (4) ◽  
pp. 829-837
Author(s):  
Baghdad Science Journal
Keyword(s):  
Mefenamic Acid ◽  
Limit Of Detection ◽  
Ion Pairs ◽  
Pharmaceutical Preparations ◽  
Correlation Coefficients ◽  
Ion Association ◽  
Pvc Membrane ◽  
Selective Determination ◽  
Ph Range

PVC membrane sensor for the selective determination of Mefenamic acid (MFA) was constructed. The sensor is based on ion association of MFA with Dodecaphospho molybdic acid (PMA) and Dodeca–Tungstophosphoric acid(PTA) as ion pairs. Nitro benzene (NB) and di-butyl phthalate (DBPH) were used as plasticizing agents in PVC matrix membranes. The specification of sensor based on PMA showed a linear response of a concentration range 1.0 × 10–2 –1.0 × 10–5 M, Nernstian slopes of 17.1-18.86 mV/ decade, detection limit of 7 × 10-5 -9.5 × 10 -7M, pH range 3 – 8 , with correlation coefficients lying between 0.9992 and 0.9976, respectively. By using the ionphore based on PTA gives a concentration range of 1.0 × 10–4 –1.0 × 10–5 M, Nernstian slope of 17.18-18.4 mV/ decade, limit of detection 8.0 × 10–6-9.3 × 10-5M,pH range 3 – 8 and correlation coefficients range between 0.9984 and 0.9891, respectively. The measurement interferences in the presence of Li+, Na+, Mg2+ Ca2+, Fe3+and Al3+ were studied using separate and match potential methods for selectivity coefficient determination. The method was applied for the determination of Mefenamic Acid in pharmaceutical preparations

scholarly journals Highly selective potentiometric determination of Fe(III) ions using Tris-(1,2-diiminocyclohexylmethyl-5-Cl-2-hydroxyl benzaldehyde) based membrane electrode

2015 ◽  
Vol 11 (8) ◽  
pp. 3798-3803
Author(s):  
M. H. Fekri ◽  
Maryam Darvishpour ◽  
M. Chegeni ◽  
H Dashti Khavidaki
Keyword(s):  
Heavy Metal ◽  
Response Time ◽  
Heavy Metal Ions ◽  
Alkaline Earth ◽  
Indicator Electrode ◽  
Membrane Electrode ◽  
Membrane Sensor ◽  
Potentiometric Response ◽  
Poly Vinyl Chloride

A novel ion-selective poly(vinyl chloride) membrane sensor for Fe(III) ions based on Tris-(1,2-diiminocyclohexylmethyl-5-Cl-2-hydroxyl benzaldehyde) are reported in this paper. The electrode exhibits a good potentiometric response for Fe(III), response time ≤ 20 s, over a wide concentration range 1.0 × 10-5 to 1.0 × 10-1 M with a slope 19.4 ± 0.5 mV/decade. The potentiometric response is independent on the pH of solution in the range of 1.5-5.0. The proposed electrode can be used for at least two months without any considerable divergence in potentials.It exhibits very good selectivity relative to a wide variety of alkali, alkaline earth, transition and heavy metal ions. The electrode assembly was also used as indicator electrode in the potentiometric titration of Fe(III) with EDTA.

Sign in / Sign up

Export Citation Format

Share Document