scholarly journals The Effect of Fabrication Method on Passive UHF RFID Tag Performance

2009 ◽  
Vol 2009 ◽  
pp. 1-8 ◽  
Author(s):  
Toni Björninen ◽  
Sari Merilampi ◽  
Leena Ukkonen ◽  
Lauri Sydänheimo ◽  
Pekka Ruuskanen
Keyword(s):  
Radio Frequency Identification ◽  
Major Effect ◽  
Skin Depth ◽  
Conducting Layer ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Manufacturing Method ◽  
Passive Uhf Rfid ◽  
Frequency Identification

In passive Radio Frequency Identification (RFID), transponders or tags are used to label objects to be identified. In this study passive tag antennas were produced using etching, screen-printing, and gravure printing methods. The threshold and backscattered signal strengths of the tags were measured to determine the effect of different manufacturing methods on the tags' performance. Conductivity, skin depth, thickness, and the quality of the conducting layer have a major effect on tag performance. Each manufacturing method sets its own boundary conditions on the processibility of the high quality conduction layer and such conditions need to be considered in tag design. Tag design also affects the manufacturing parameters used in the different techniques. The results of the study show that each of the studied fabrication methods can be used to manufacture reliable RFID tags.

scholarly journals Different Substrate Materials for Designing a Passive UHF RFID Tag Antenna

2019 ◽  
Vol 8 (9S) ◽  
pp. 572-580 ◽  
Keyword(s):  
Radio Frequency Identification ◽  
Impedance Matching ◽  
Dipole Antenna ◽  
Antenna Gain ◽  
Rfid Technology ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Passive Uhf Rfid ◽  
Frequency Identification ◽  
Read Range

The Radio Frequency Identification (RFID) technology has been increasingly used for various application such as tracking of products, smart cards, identification, item management, security etc. In this paper, the performance parameter of the passive UHF RFID tag antenna has been studied for four different substrate materials viz., FR4 epoxy, PET, Rogers 4350, Taconic TLY materials. A simple meandered dipole antenna has been designed using a T-match stub for impedance matching of the tag antenna with the attached RFID chip. These different substrates are then designed separately, for the same antenna geometry. The effect of using these substrates on RFID tag antenna parameters such as reflection coefficient, antenna gain, VWSR, radiation pattern, impedance, ease of optimization level, read range, and radiation efficiency are then observed.

scholarly journals Analysis and exploitation of harmonics in wireless power transfer (H-WPT): passive UHF RFID case

2014 ◽  
Vol 1 (2) ◽  
pp. 65-74 ◽  
Author(s):  
Gianfranco Andia Vera ◽  
Yvan Duroc ◽  
Smail Tedjini
Keyword(s):  
Radio Frequency Identification ◽  
Dual Band ◽  
Uhf Rfid ◽  
Wireless Power ◽  
Rfid Tag ◽  
Passive Uhf Rfid ◽  
Harmonic Signals ◽  
Analysis Methodology ◽  
Frequency Identification

This paper discusses novel methodologies for the characterization of harmonic signals generated by wireless powered devices, i.e. passive ultra-high frequency (UHF) radio frequency identification (RFID) tags, due to the wireless power transferred from reader to tag. Theoretical aspects, as well as measurements to characterize these non-linear phenomena are exposed. Particular care is taken to explain the analysis methodology and setup for two kinds of characterization measurements: radiated and conducted. The existence of harmonic signals carrying information is exploited in an advanced application example. A dual-band RFID tag is designed to increase the backscattered harmonic level in the tag-to-reader link. Measurement of this dual band tag demonstrates the exploitation of the hitherto neglected harmonic power; it also opens the door to more advanced applications exploiting the harmonic-link communication.

scholarly journals Integrating Passive UHF RFID Tags with WSN Nodes: Challenges and Opportunities

2014 ◽  
Vol 10 (2) ◽  
pp. 99 ◽  
Author(s):  
Luigi Patrono
Keyword(s):  
Radio Frequency Identification ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Passive Uhf Rfid ◽  
Integration Approach ◽  
Challenges And Opportunities ◽  
Class 1 ◽  
Frequency Identification ◽  
New Generation ◽  
The Internet Of Things

Radio Frequency Identification (RFID) and Wireless Sensor Networks (WSNs) have received an ever-increasing attention in recent years, mainly because they represent two of the most important technologies enabling the Internet of Things vision. Although designed originally with different objectives, WSN and RFID represent two complementary technologies whose integration might increase their functionalities and extend their range of applications. However, important technological issues must still be solved in order to fully exploit the potentialities offered by such integration. In this work, an innovative RFID-WSN integration approach is presented and validated. It relies on the interconnection of a new-generation, long-range, EPCglobal Class-1 Generation-2 Ultra-High-Frequency (UHF) RFID tag with a commercial WSN node via the I2C interface. Experimental results have demonstrated the effectiveness of the proposed approach compared to existing solution in the literature. Interesting application scenarios enabled by the proposed RFID-WSN integration approach are briefly summarized at the end of the paper.

scholarly journals Longest-Range UHF RFID Sensor Tag Antenna for IoT Applied for Metal and Non-Metal Objects

Sensors ◽  
2019 ◽  
Vol 19 (24) ◽  
pp. 5460 ◽  
Author(s):  
Franck Kimetya Byondi ◽  
Youchung Chung
Keyword(s):  
Wireless Sensor Networks ◽  
Radio Frequency Identification ◽  
High Frequency ◽  
Wireless Sensor ◽  
The Internet ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Frequency Identification ◽  
The Internet Of Things ◽  
Read Range

This paper presents a passive cavity type Ultra High Frequency (UHF) Radio Frequency Identification (RFID) tag antenna having the longest read-range, and compares it with existing long-range UHF RFID tag antenna. The study also demonstrates mathematically and experimentally that our proposed longest-range UHF RFID cavity type tag antenna has a longer read-range than existing passive tag antennas. Our tag antenna was designed with 140 × 60 × 10 mm3 size, and reached 26 m measured read-range and 36.3 m mathematically calculated read-range. This UHF tag antenna can be applied to metal and non-metal objects. By adding a further sensing capability, it can have a great benefit for the Internet of Things (IoT) and wireless sensor networks (WSN).

Structure optimization of an ultrahigh frequency radio frequency identification tag thread based on the normal mode helix dipole antenna

2020 ◽  
pp. 004051752094890
Author(s):  
Yong Zhang ◽  
Jiyong Hu ◽  
Xiong Yan ◽  
Xudong Yang
Keyword(s):  
Resonant Frequency ◽  
Normal Mode ◽  
Radio Frequency Identification ◽  
Dipole Antenna ◽  
Uhf Rfid ◽  
Simulation Experiments ◽  
Rfid Tag ◽  
Helical Pitch ◽  
Frequency Identification ◽  
Linear Dipole

This paper describes the design of a novel ultrahigh frequency radio frequency identification (UHF RFID) tag thread that mainly consisted of the common yarn and the normal mode helix dipole antenna. The linear dipole antenna for the UHF RFID tag thread was too long to miniaturize the tag. In order to maximize the read performance and miniaturize the size of the tag, the basic antenna structure parameters, such as the helical pitch and single arm length, were optimized by analyzing the radiation parameter S11 of the normal mode helix dipole antenna based on simulation experiments. The simulation experiments started with optimizing the single arm length to obtain the minimum of the S11 parameter at resonant frequency, then the helical pitch was further optimized to limit the resonant frequency to the UHF range. The simulation results showed the resonant frequency rises with an increase of helical pitch and declines with an increase of single arm length. Furthermore, a series of UHF RFID tag threads with good performance from the simulation cases were prepared, and the performance of the optimized tag was validated. Generally, the UHF RFID tag thread with optimized helix dipole antenna could reduce the axial length of the tag by 57% and improve the reading range by 500%, and its performance was greatly superior to that of the UHF RFID tag thread with the classical linear dipole antenna.

A Novel Design of PIE Decoding with Multiple CRC Circuit for RFID Tag

2013 ◽  
Vol 816-817 ◽  
pp. 957-961
Author(s):  
Feng Ying Huang ◽  
Jun Wang ◽  
Yu Sen Xu ◽  
Ji Wei Huang
Keyword(s):  
Data Processing ◽  
Parallel Algorithm ◽  
Radio Frequency Identification ◽  
High Frequency ◽  
Pulse Interval ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Frequency Identification ◽  
Simulation Results ◽  
Novel Design

This paper proposes a new synchronized serial-parallel CRC(Cycle Redundancy Check) with PIE(Pulse Interval Encoding) decoding circuit for the UHF(Ultra-High Frequency) RFID(Radio Frequency Identification), which is based on the ISO/IEC 18000-6C standards protocol. The parallel algorithm of CRC circuit is derived, and the serial or parallel CRC circuit on RFID tag chip is evaluated in this paper. Finally, the designed circuit is simulated and analyzed on the FPGA platform. Simulation results show that the proposed circuit meets the communication requirement of the protocol and addresses the problem of low data processing rate of conventional serial CRC circuit, as well as implements 1 to 8 degree of parallelism of the parallel CRC circuit for UHF RFID.

scholarly journals Stretchable Textile Yarn Based on UHF RFID Helical Tag

Textiles ◽  
2021 ◽  
Vol 1 (3) ◽  
pp. 547-557
Author(s):  
Sofia Benouakta ◽  
Florin Doru Hutu ◽  
Yvan Duroc
Keyword(s):  
Radio Frequency Identification ◽  
Textile Yarn ◽  
Radiative Properties ◽  
Rfid Tags ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Half Wave ◽  
Present Solution ◽  
Frequency Identification ◽  
Helical Geometry

In the context of wearable technology, several techniques have been used for the fabrication of radio frequency identification (RFID) tags such as 3D printing, inkjet printing, and even embroidery. In contrast to these methods where the tag is attached to the object by using sewing or simple sticking, the E-Thread® technology is a novel assembling method allowing for the integration of the RFID tag into a textile yarn and thus makes it embeddable into the object at the fabrication stage. The current E-Thread® yarn uses a RFID tag in which the antenna is a straight half-wave dipole that makes the solution vulnerable to mechanical strains (i.e., elongation). In this paper, we propose an alternative to the current RFID yarn solution with the use of an antenna having a helical geometry that answers to the mechanical issues and keeps quite similar electrical and radiative properties with respect to the present solution. The RFID helical tag was designed and simulated taking into consideration the constraints of the manufacturing process. The helical RFID tag was then fabricated using the E-Thread® technology and experimental characterization showed that the obtained structure exhibited good performance with 10.6 m of read range in the ultra high frequency (UHF) RFID band and 10% of tolerance in terms of elongation.

A design of analog VDD generator for passive UHF RFID Tag in 90 nm CMOS

2014 ◽  
Vol 7 (5) ◽  
pp. 507-513 ◽  
Author(s):  
Smail Hassouni ◽  
Hassan Qjidaa
Keyword(s):  
Radio Frequency Identification ◽  
Schottky Diodes ◽  
Input Power ◽  
Cmos Process ◽  
Uhf Rfid ◽  
Chip Area ◽  
Rfid Tag ◽  
Passive Uhf Rfid ◽  
Low Power Dissipation ◽  
Simulation Results

This paper introduces a VDD generator for the ultrahigh frequency (UHF) passive Radio-frequency identification (RFID) tag, consisting of an RF-limiter, an NMOS rectifier, a DC-limiter, and a regulator. The proposed NMOS rectifier utilizes diode-connected native NMOS transistors with ultralow-threshold voltage instead of Schottky diodes. The theoretical equations for predicting the performance of the VDD generator are provided and verified by both simulation results in 90 nm CMOS process. The proposed VDD generator generates a 1.19-V stable output voltage with low-power dissipation and a 26.96% larger power conversion efficiency under conditions of 50 Ω antenna, 900 MHz, −23 dBm input power and 1 M DC output load. The chip area of the proposed VDD generator is only 105 × 85 μm. The simulation results indicated that the presented novel VDD generator is capable to provide efficient, stable, and input-independent power supply for Passive UHF RFID tag

scholarly journals Brush-Painting and Photonic Sintering of Copper Oxide and Silver Inks on Wood and Cardboard Substrates to Form Antennas for UHF RFID Tags

2016 ◽  
Vol 2016 ◽  
pp. 1-8 ◽  
Author(s):  
Erja Sipilä ◽  
Johanna Virkki ◽  
Jianhua Wang ◽  
Lauri Sydänheimo ◽  
Leena Ukkonen
Keyword(s):  
Copper Oxide ◽  
Radio Frequency Identification ◽  
Rfid Tags ◽  
Uhf Rfid ◽  
Rfid Tag ◽  
Wireless Testing ◽  
Silver Ink ◽  
Frequency Identification ◽  
Remote Identification ◽  
Photonic Sintering

Additive deposition of inks with metallic inclusions provides compelling means to embed electronics into versatile structures. The need to integrate electronics into environmentally friendly components and structures increases dramatically together with the increasing popularity of the Internet of Things. We demonstrate a novel brush-painting method for depositing copper oxide and silver inks directly on wood and cardboard substrates and discuss the optimization of the photonic sintering process parameters for both materials. The optimized parameters were utilized to manufacture passive ultra high frequency (UHF) radio frequency identification (RFID) tag antennas. The results from wireless testing show that the RFID tags based on the copper oxide and silver ink antennas on wood substrate are readable from ranges of 8.5 and 11 meters, respectively, and on cardboard substrate from read ranges of 8.5 and 12 meters, respectively. These results are well sufficient for many future wireless applications requiring remote identification with RFID.

scholarly journals Localization of passive UHF RFID Labels with Kalman Filter

2012 ◽  
Vol 10 ◽  
pp. 119-125 ◽  
Author(s):  
T. Nick ◽  
J. Götze
Keyword(s):  
Kalman Filter ◽  
Radio Frequency Identification ◽  
Unscented Kalman Filter ◽  
Uhf Rfid ◽  
Received Signal Strength Indicator ◽  
Localization Accuracy ◽  
Passive Uhf Rfid ◽  
Reader Antenna ◽  
Reference Tags ◽  
Frequency Identification

Abstract. Localization via Radio Frequency Identification (RFID) is frequently used in different applications nowadays. It has the advantage that next to its ostensible purpose of identifying objects via their unique IDs it can simultaneously be used for the localization of these objects. In this work it is shown how Received Signal Strength Indicator (RSSI) measurements at different antennae of a passive UHF RFID label can be combined for localization. The localization is only done based on the RSSI measurements and a Kalman Filter (KF). Because of non-linearities in the measurement function it is necessary to incorporate an Extended Kalman Filter (EKF) or an Unscented Kalman Filter (UKF) where simulations have shown that the UKF performs better than the EKF. Additionally to the selection of the filter there are different possibilities to increase the localization accuracy of the UKF: The advantages of using Reference Tags (RT) or more than one tag per trolley (relative positioning) in combination with an Unscented Kalman Filter are discussed and simulations results show that the localization error can be decreased significantly via these methods. Another possibility to increase the localization accuracy and in addition to achieve a more realistic simulation is the consideration of the angle between reader antenna and tag. Simulation results with the incorporation of different numbers of fixed antennae lead to the conclusion that this is a useful surplus in the localization.

Sign in / Sign up

Export Citation Format

Share Document