scholarly journals Traces Synchronization in Distributed Networks

2009 ◽  
Vol 2009 ◽  
pp. 1-11 ◽  
Author(s):  
Eric Clément ◽  
Michel Dagenais
Keyword(s):  
Distributed System ◽  
Large Time ◽  
Least Square ◽  
System Level ◽  
Time Interval ◽  
Execution Traces ◽  
Novel Approach ◽  
Least Square Fit ◽  
Time Offset ◽  
The Individual

This article proposes a novel approach to synchronize a posteriori the detailed execution traces from several networked computers. It can be used to debug and investigate complex performance problems in systems where several computers exchange information. When the distributed system is under study, detailed execution traces are generated locally on each system using an efficient and accurate system level tracer, LTTng. When the tracing is finished, the individual traces are collected and analysed together. The messaging events in all the traces are then identified and correlated in order to estimate the time offset over time between each node. The time offset computation imprecision, associated with asymmetric network delays and operating system latency in message sending and receiving, is amortized over a large time interval through a linear least square fit over several messages covering a large time span. The resulting accuracy is such that it is possible to estimate the clock offsets in a distributed system, even with a relatively low volume of messages exchanged, to within the order of a microsecond while having a very low impact on the system execution, which is sufficient to properly order the events traced on the individual computers in the distributed system.

Least-square refinement of structure parameters from CBED integrated intensities: application to determination of temperature factors in Y BA2CU3O7

1992 ◽  
Vol 50 (2) ◽  
pp. 1456-1457
Author(s):  
Kjersti Gjønnes ◽  
Jon Gjønnes
Keyword(s):  
Least Square ◽  
Measured Intensity ◽  
Structure Information ◽  
Accurate Temperature ◽  
Least Square Fit ◽  
Case Application ◽  
Integrated Intensities ◽  
Temperature Factors ◽  
Narrow Bands

Electron diffraction intensities can be obtained at large scattering angles (sinθ/λ ≥ 2.0), and thus structure information can be collected in regions of reciprocal space that are not accessable with other diffraction methods. LACBED intensities in this range can be utilized for determination of accurate temperature factors or for refinement of coordinates. Such high index reflections can usually be treated kinematically or as a pertubed two-beam case. Application to Y Ba2Cu3O7 shows that a least square refinememt based on integrated intensities can determine temperature factors or coordinates.LACBED patterns taken in the (00l) systematic row show an easily recognisable pattern of narrow bands from reflections in the range 15 < l < 40 (figure 1). Integrated intensities obtained from measured intensity profiles after subtraction of inelastic background (figure 2) were used in the least square fit for determination of temperature factors and refinement of z-coordinates for the Ba- and Cu-atoms.

scholarly journals System models for resilience in gerontology: application to the COVID-19 pandemic

2021 ◽  
Vol 21 (1) ◽  
Author(s):  
Katarzyna Klasa ◽  
Stephanie Galaitsi ◽  
Andrew Wister ◽  
Igor Linkov
Keyword(s):  
The Elderly ◽  
System Level ◽  
Improve Quality ◽  
Care Needs ◽  
Individual Level ◽  
Chronic Stressors ◽  
The World ◽  
Aging Adults ◽  
The Individual

AbstractThe care needs for aging adults are increasing burdens on health systems around the world. Efforts minimizing risk to improve quality of life and aging have proven moderately successful, but acute shocks and chronic stressors to an individual’s systemic physical and cognitive functions may accelerate their inevitable degradations. A framework for resilience to the challenges associated with aging is required to complement on-going risk reduction policies, programs and interventions. Studies measuring resilience among the elderly at the individual level have not produced a standard methodology. Moreover, resilience measurements need to incorporate external structural and system-level factors that determine the resources that adults can access while recovering from aging-related adversities. We use the National Academies of Science conceptualization of resilience for natural disasters to frame resilience for aging adults. This enables development of a generalized theory of resilience for different individual and structural contexts and populations, including a specific application to the COVID-19 pandemic.

Using hidden Markov models to find discrete targets in continuous sociophonetic data

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Daniel Duncan
Keyword(s):  
Hidden Markov Models ◽  
Markov Models ◽  
Hidden Markov ◽  
Abstract Representation ◽  
Language Variation And Change ◽  
Novel Approach ◽  
Single Target ◽  
The Individual ◽  
Individual Speaker

Abstract Advances in sociophonetic research resulted in features once sorted into discrete bins now being measured continuously. This has implied a shift in what sociolinguists view as the abstract representation of the sociolinguistic variable. When measured discretely, variation is variation in selection: one variant is selected for production, and factors influencing language variation and change are influencing the frequency at which variants are selected. Measured continuously, variation is variation in execution: speakers have a single target for production, which they approximate with varying success. This paper suggests that both approaches can and should be considered in sociophonetic analysis. To that end, I offer the use of hidden Markov models (HMMs) as a novel approach to find speakers’ multiple targets within continuous data. Using the lot vowel among whites in Greater St. Louis as a case study, I compare 2-state and 1-state HMMs constructed at the individual speaker level. Ten of fifty-two speakers’ production is shown to involve the regular use of distinct fronted and backed variants of the vowel. This finding illustrates HMMs’ capacity to allow us to consider variation as both variant selection and execution, making them a useful tool in the analysis of sociophonetic data.

scholarly journals HPM: A Hybrid Model for User’s Behavior Prediction Based on N-Gram Parsing and Access Logs

2020 ◽  
Vol 2020 ◽  
pp. 1-18
Author(s):  
Sonia Setia ◽  
Verma Jyoti ◽  
Neelam Duhan
Keyword(s):  
Web Mining ◽  
Contextual Information ◽  
Hybrid Approach ◽  
Web Pages ◽  
Continuous Growth ◽  
Novel Approach ◽  
Content Mining ◽  
Long Access ◽  
N Gram ◽  
The Individual

The continuous growth of the World Wide Web has led to the problem of long access delays. To reduce this delay, prefetching techniques have been used to predict the users’ browsing behavior to fetch the web pages before the user explicitly demands that web page. To make near accurate predictions for users’ search behavior is a complex task faced by researchers for many years. For this, various web mining techniques have been used. However, it is observed that either of the methods has its own set of drawbacks. In this paper, a novel approach has been proposed to make a hybrid prediction model that integrates usage mining and content mining techniques to tackle the individual challenges of both these approaches. The proposed method uses N-gram parsing along with the click count of the queries to capture more contextual information as an effort to improve the prediction of web pages. Evaluation of the proposed hybrid approach has been done by using AOL search logs, which shows a 26% increase in precision of prediction and a 10% increase in hit ratio on average as compared to other mining techniques.

scholarly journals Rotor Interaction Noise in Counter-Rotating Propfan Propulsion Systems

2011 ◽  
Vol 134 (1) ◽  
Author(s):  
Andreas Peters ◽  
Zoltán S. Spakovszky
Keyword(s):  
Polar Angle ◽  
Secondary Flows ◽  
Tip Vortex ◽  
System Level ◽  
Analysis Tool ◽  
Acoustic Analogy ◽  
Wake Interaction ◽  
Open Rotor ◽  
And Performance ◽  
The Individual

Due to their inherent noise challenge and potential for significant reductions in fuel burn, counter-rotating propfans (CRPs) are currently being investigated as potential alternatives to high-bypass turbofan engines. This paper introduces an integrated noise and performance assessment methodology for advanced propfan powered aircraft configurations. The approach is based on first principles and combines a coupled aircraft and propulsion system mission and performance analysis tool with 3D unsteady, full-wheel CRP computational fluid dynamics computations and aeroacoustic simulations. Special emphasis is put on computing CRP noise due to interaction tones. The method is capable of dealing with parametric studies and exploring noise reduction technologies. An aircraft performance, weight and balance, and mission analysis was first conducted on a candidate CRP powered aircraft configuration. Guided by data available in the literature, a detailed aerodynamic design of a pusher CRP was carried out. Full-wheel unsteady 3D Reynolds-averaged Navier-Stokes (RANS) simulations were then used to determine the time varying blade surface pressures and unsteady flow features necessary to define the acoustic source terms. A frequency domain approach based on Goldstein’s formulation of the acoustic analogy for moving media and Hanson’s single rotor noise method was extended to counter-rotating configurations. The far field noise predictions were compared to measured data of a similar CRP configuration and demonstrated good agreement between the computed and measured interaction tones. The underlying noise mechanisms have previously been described in literature but, to the authors’ knowledge, this is the first time that the individual contributions of front-rotor wake interaction, aft-rotor upstream influence, hub-endwall secondary flows, and front-rotor tip-vortices to interaction tone noise are dissected and quantified. Based on this investigation, the CRP was redesigned for reduced noise incorporating a clipped rear-rotor and increased rotor-rotor spacing to reduce upstream influence, tip-vortex, and wake interaction effects. Maintaining the thrust and propulsive efficiency at takeoff conditions, the noise was calculated for both designs. At the interaction tone frequencies, the redesigned CRP demonstrated an average reduction of 7.25 dB in mean sound pressure level computed over the forward and aft polar angle arcs. On the engine/aircraft system level, the redesigned CRP demonstrated a reduction of 9.2 dB in effective perceived noise (EPNdB) and 8.6 EPNdB at the Federal Aviation Regulations (FAR) 36 flyover and sideline observer locations, respectively. The results suggest that advanced open rotor designs can possibly meet Stage 4 noise requirements.

LONG‐TIME RESPONSE PREDICTED BY EXACT ELASTIC RAY THEORY

Geophysics ◽  
1965 ◽  
Vol 30 (3) ◽  
pp. 363-368 ◽  
Author(s):  
T. W. Spencer
Keyword(s):  
Formal Solution ◽  
Intermediate Stage ◽  
Time Limit ◽  
Time Interval ◽  
Individual Response ◽  
Axially Symmetric ◽  
Long Time ◽  
The Difference ◽  
The Individual ◽  
Significant Figures

The formal solution for an axially symmetric radiation field in a multilayered, elastic system can be expanded in an infinite series. Each term in the series is associated with a particular raypath. It is shown that in the long‐time limit the individual response functions produced by a step input in particle velocity are given by polynomials in odd powers of the time. For rays which suffer m reflections, the degree of the polynomials is 2m+1. The total response is obtained by summing all rays which contribute in a specified time interval. When the rays are selected indiscriminately, the difference between the magnitude of the partial sum at an intermediate stage of computation and the magnitude of the correct total sum may be greater than the number of significant figures carried by the computer. A prescription is stated for arranging the rays into groups. Each group response function varies linearly in the long‐time limit and goes to zero when convolved with a physically realizable source function.

A Screw-Theoretic Analysis Framework for Payload Manipulation by Mobile Manipulator Collectives

2005 ◽  
Author(s):  
Rajankumar Bhatt ◽  
Chin Pei Tang ◽  
Michel Abou-Samah ◽  
Venkat Krovi
Keyword(s):  
System Performance ◽  
Single Agent ◽  
Physical Nature ◽  
Theoretical Background ◽  
System Level ◽  
Mobile Manipulator ◽  
Test Bed ◽  
Tight Coupling ◽  
Constrained Mechanical Systems ◽  
The Individual

In recent times, there has been considerable interest in creating and deploying modular cooperating collectives of robots. Interest in such cooperative systems typically arises when certain tasks are either too complex to be performed by a single agent or when there are distinct benefits that accrue by cooperation of many simple robotic modules. However, the nature of the both the individual modules as well as their interactions can affect the overall system performance. In this paper, we examine this aspect in the context of cooperative payload transport by robot collectives wherein the physical nature of the interactions between the various modules creates a tight coupling within the system. We leverage the rich theoretical background of analysis of constrained mechanical systems to provide a systematic framework for formulation and evaluation of system-level performance on the basis of the individual-module characteristics. The composite multi-d.o.f wheeled vehicle, formed by supporting a common payload on the end-effectors of multiple individual mobile manipulator modules, is treated as an in-parallel system with articulated serial-chain arms. The system-level model, constructed from the twist- and wrench-based models of the attached serial chains, can then be systematically analyzed for performance (in terms of mobility and disturbance rejection.) A 2-module composite system example is used through the paper to highlight various aspects of the systematic system model formulation, effects of selection of the actuation at the articulations (active, passive or locked) on system performance and experimental validation on a hardware prototype test bed.

Interventions Promoting Educators’ Use of Data: Research Insights and Gaps

2012 ◽  
Vol 114 (11) ◽  
pp. 1-48 ◽  
Author(s):  
Julie A. Marsh
Keyword(s):  
Data Collection ◽  
Research Question ◽  
Time Frame ◽  
System Level ◽  
Quality Of Data ◽  
Leverage Points ◽  
Knowledge To Action ◽  
Use Of Data ◽  
The Individual ◽  
Capacity Data

Background/Context In recent years, states, districts, schools, and external partners have recognized the need to proactively foster the use of data to guide educational decision-making and practice. Understanding that data alone will not guarantee use, individuals at all levels have invested in interventions to support better access to, interpretation of, and responses to data of all kinds. Despite the emergence of these efforts, there has been little systematic examination of research on such efforts. Purpose/Objective/Research Question/Focus of Study This article synthesizes what we currently know about interventions to support educators’ use of data—ranging from comprehensive, system-level initiatives, such as reforms sponsored by districts or intermediary organizations, to more narrowly focused interventions, such as a workshop. The article summarizes what is what is known across studies about the design and implementation of these interventions, their effects at the individual and organizational levels, and the conditions shown to affect implementation and outcomes. Research Design Literature review. Data Collection and Analysis This review entailed systematic searches of electronic databases and careful sorting to yield a total of 41 books, peer-reviewed journal articles, and reports. Summaries of each publication were coded to identify the study methods (design, framework, sample, time frame, data collection), intervention design (level of schooling, focal data and data user, leverage points, components), and findings on implementation, effects, and conditions. Findings/Results The review uncovers a host of common themes regarding implementation, including promising practices (e.g., making data “usable” and “safe,” targeting multiple leverage points) and persistent challenges (e.g., developing support that is generic but also customized, sustaining sufficient support). The review also finds mixed findings and levels of research evidence on effects of interventions, with relatively more evidence on effects on educators’ knowledge, skills, and practice than on effects on organizations and student achievement. The article also identifies a set of common conditions found to influence intervention implementation and effects, including intervention characteristics (capacity, data properties), broader context (leadership, organizational structure), and individual relationships and characteristics (trust, beliefs and knowledge). Conclusions/Recommendations The review finds that the current research base is limited in quantity and quality. It suggests the need for more methodologically rigorous research and greater attention to the organizational and student-level outcomes of interventions, comparative analyses, interventions that help educators move from knowledge to action, and specific ways in which the quality of data and leadership practices shape the effectiveness of interventions.

Array design

1968 ◽  
Vol 58 (3) ◽  
pp. 977-991
Author(s):  
Richard A. Haubrich
Keyword(s):  
High Resolution ◽  
Data Processing ◽  
Least Square ◽  
Wave Number ◽  
Array Design ◽  
Least Square Fit ◽  
The Difference ◽  
Set Of Points ◽  
Array Output

abstract Arrays of detectors placed at discrete points are often used in problems requiring high resolution in wave number for a limited number of detectors. The resolution performance of an array depends on the positions of detectors as well as the data processing of the array output. The performance can be expressed in terms of the “spectrum window”. Spectrum windows may be designed by a general least-square fit procedure. An alternate approach is to design the array to obtain the largest uniformly spaced coarray, the set of points which includes all the difference spacings of the array. Some designs obtained from the two methods are given and compared.

Sign in / Sign up

Export Citation Format

Share Document