scholarly journals Experimental Investigation of Innovative Internal Trailing Edge Cooling Configurations with Pentagonal Arrangement and Elliptic Pin Fin

2008 ◽  
Vol 2008 ◽  
pp. 1-10 ◽  
Author(s):  
L. Tarchi ◽  
B. Facchini ◽  
S. Zecchi
Keyword(s):  
Heat Transfer ◽  
Spanwise Direction ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Transient Technique ◽  
Pressure Losses ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Pin Fins ◽  
Data Reduction Method

This paper describes a heat transfer experimental study of four different internal trailing edge cooling configurations based on pin fin schemes. The aim of the study is the comparison between innovative configurations and standard ones. So, a circular pin fin configuration with an innovative pentagonal scheme is compared to a standard staggered scheme, while two elliptic pin fin configurations are compared to each other turning the ellipse from the streamwise to the spanwise direction. For each configuration, heat transfer and pressure loss measurements were made keeping the Mach number fixed at 0.3 and varying the Reynolds number from 9000 to 27000. In order to investigate the overall behavior of both endwall and pedestals, heat transfer measurements are performed using a combined transient technique. Over the endwall surface, the classic transient technique with thermochromic liquid crystals allows the measurement of a detailed heat transfer coefficient (HTC) map. Pin fins are made of high thermal conductivity material, and an inverse data reduction method based on a finite element code allows to evaluate the mean HTC of each pin fin. Results show that the pentagonal arrangement generates a nonuniform HTC distribution over the endwall surface, while, in terms of average values, it is equivalent to the staggered configuration. On the contrary, the HTC map of the two elliptic configurations is similar, but the spanwise arrangement generates higher heat transfer coefficients and pressure losses.

Heat Transfer in Rotating, Trailing Edge, Converging Channels With Partial Length Pin-Fins

2021 ◽  
Vol 143 (6) ◽  
Author(s):  
Izzet Sahin ◽  
I-Lun Chen ◽  
Lesley M. Wright ◽  
Je-Chin Han ◽  
Hongzhou Xu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Slight Reduction ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Partial Length ◽  
Pin Fins ◽  
Cooling Passage

Abstract In the current study, the heat transfer and pressure drop characteristics of a rotating, partial pin-finned, cooling channel that has a trapezoidal cross section and converges from the hub to tip in both the streamwise and spanwise directions are experimentally investigated. To model the geometry of an internal trailing edge cooling passage, the channel is oriented with respect to the direction of rotation (β = 120 deg). Isolated copper plates are used to obtain regionally averaged heat transfer coefficients on the leading and trailing surfaces. Pressure drop is measured using pressure taps placed at the inlet and outlet of the channel. Utilizing Dp = 5 mm diameter pins, a staggered array is created. For this array, the streamwise pin-spacing, Sy/Dp = 2.1, was kept constant; however, the spanwise pin-spacing, Sx/Dp, was varied from the hub to tip between 3 and 2.6 due to the channel convergence. Experiments were conducted for two partial pin-fin sets having pin length-to-diameter ratios of Sz/Dp = 0.4 and 0.2. The rotation number was varied from 0 to 0.21 by ranging the inlet Reynolds number from 10,000 to 40,000 and rotation speed from 0 to 300 rpm. A significant decrease in pressure loss and a slight reduction in heat transfer enhancement are observed with the use of partial pin-fins compared with the previously reported full pin-fin converging channel study. This provides better thermal performances of the partial pin-fin arrays compared with the full pin-fin array, in the converging channels.

Pedestal and Endwall Contribution in Heat Transfer in Thin Wedge Shaped Trailing Edge

2004 ◽  
Author(s):  
Bruno Facchini ◽  
Luca Innocenti ◽  
Lorenzo Tarchi
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Thermochromic Liquid Crystal ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Transient Technique ◽  
Heat Transfer Coefficients ◽  
Pin Fins ◽  
Turbine Airfoils ◽  
Accelerating Flow

Short pin fins (pedestals) and long ribs (enlarged pedestals) are usually used in trailing edge cooling of turbine airfoils. To better reproduce the geometry of such cooling systems, test section of this experimental study is a wedge duct with inserts, to take into account effects of accelerating flow. A complete investigation of the system needs a separate evaluation of the heat transfer coefficients (HTC) for the pedestal surface and for the free endwall surface. In the present work an innovative technique made of different methods for these two different regions is presented, so cooling performances of each are evaluated. Thermochromic liquid crystal (TLC) transient technique is used to measure detailed heat transfer coefficients only on the endwall surface: a typical transparent (Plexiglas®) test article is used. Aluminum pedestals, employing a procedure based on a finite elements code, allow to measure the average heat transfer coefficient on the insert surface. To investigate the effects on transient technique of high conductive components, a comparison with Plexiglas inserts has been performed. Results show an underestimation of HTC with TLC transient technique only for aluminum long ribs at low Reynolds number values. Nevertheless the results seem to agree with other authors both for the endwall surface and for the entire cooling system.

Single-Phase Heat Transfer in Mems-Based Pin Fin Heat Sink

2005 ◽  
Author(s):  
Ali Kosar ◽  
Yoav Peles
Keyword(s):  
Heat Transfer ◽  
Single Phase ◽  
Reynolds Numbers ◽  
Heat Fluxes ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Nusselt Numbers ◽  
Pin Fins ◽  
Micro Pin Fins

An experimental study has been performed on single-phase heat transfer of de-ionized water over a bank of shrouded micro pin fins 243-μm long with hydraulic diameter of 99.5-μm. Heat transfer coefficients and Nusselt numbers have been obtained over effective heat fluxes ranging from 3.8 to 167 W/cm2 and Reynolds numbers from 14 to 112. The results were used to derive the Nusselt numbers and total thermal resistances. It has been found that endwalls effects are significant at low Reynolds numbers and diminish at higher Reynolds numbers.

Heat Transfer in a Rib and Pin Roughened Rotating Multi-Pass Channel With Hub Turning Vane and Trailing-Edge Slot Ejection

2015 ◽  
Author(s):  
Hao-Wei Wu ◽  
Hootan Zirakzadeh ◽  
Je-Chin Han ◽  
Luzeng Zhang ◽  
Hee-Koo Moon
Keyword(s):  
Heat Transfer ◽  
Side Wall ◽  
Internal Cooling ◽  
Test Model ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
The Third ◽  
Pin Fins ◽  
Cooling Air

A three-passage internal cooling test model with a 180° U-bend at the hub turn portion was used to perform the investigation. The flow is radially inward at the second passage, while it is radially outward at the third passage after the U-bend. Measurement was conducted at the second and the third passages. Aspect ratio of the second passage is 2:1 (AR=2), while the third passage is wedge-shaped with side wall slot ejections. The squared ribs with P/e = 8, e/Dh = 0.1, α = 45°, were configured on both leading and trailing surfaces along the second passage, and also the inner half of the third passage. Three rows of cylinder-shaped pin-fins with diameter of 3 mm were placed at both leading and trailing surfaces of the outer half of the third passage. The results showed that the rotating effects on radial inward flow and radial outward flow are consistent with previous studies. When there is no turning vane, heat transfer on the leading surface at hub turn region is increased by rotation, while it is decreased on the trailing surface. The presence of turning vane reduces the effect of rotation on hub turn portion. Ejection and pin-fin array enhance heat transfer at the third passage. Even though there is mass loss of cooling air along the third passage with side wall slot ejection, the heat transfer coefficient remains high until the end of the passage. Correlation between regional heat transfer coefficients and rotation numbers is presented for both cases of with and without turning vane.

A Novel Concept to Improve the Performance of LED Panel Using Drilled Holes

2005 ◽  
Author(s):  
S. B. Chiang ◽  
C. C. Wang
Keyword(s):  
Heat Transfer ◽  
Surface Area ◽  
Heat Sink ◽  
Maximum Temperature ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Pin Fins ◽  
Overall Performance ◽  
Novel Concept

In this study, the concept of the thermal module of LEDs cooling by use of drilled hole to entrain air flow was examined. It is found that the drilled hole does not necessarily improve the overall performance. It depends on the size of the drilled hole, the number of drilled holes, and the locations. The heat transfer coefficients are generally increased with the number of drilled holes and the diameter of the drilled hole. In this paper, the plate fin heat sink has a higher heat transfer coefficients than pin fins, but the overall performance of the LED panel having pin fin outperforms that of plate fin. This is because the pin fin provides much larger surface area. For decrease the maximum temperature of the LED panel, placement of the drilled holes along the hot region will be more effective.

scholarly journals Length to Diameter Ratio and Row Number Effects in Short Pin Fin Heat Transfer

1984 ◽  
Vol 106 (1) ◽  
pp. 241-244 ◽  
Author(s):  
B. A. Brigham ◽  
G. J. VanFossen
Keyword(s):  
Heat Transfer ◽  
Diameter Ratio ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Relative Contribution ◽  
Pin Fins ◽  
Lower Heat ◽  
Tube Banks ◽  
Length To Diameter Ratio

Recently, several experiments concerning heat transfer from short pin fins have been conducted with the results indicating lower heat transfer from short pin fins than from longer pin fins found in tube banks and other similar configurations. Assessments of the effect of the number of pin rows and row geometry have also been made. It was felt that there was a need to determine the relative contribution of pin length to diameter ratio and pin row geometry on the heat transfer. Array-averaged heat transfer coefficients on pin and endwall surfaces were measured for two configurations of staggered arrays of short pin fins (length to diameter ratio of 4). One configuration contained eight streamwise rows of pins, while the other contained only four rows. Results showed that both the eight-row and the four-row configurations for an Lp/D of 4 exhibit higher heat transfer than in similar tests on shorter pin fins (Lp/D of 1/2 and 2). It was also found that for this Lp/D ratio the array-averaged heat transfer was slightly higher with eight rows of staggered pins than with only four rows.

scholarly journals Heat Transfer Coefficients for Staggered Arrays of Short Pin Fins

1981 ◽  
Author(s):  
G. J. VanFossen
Keyword(s):  
Heat Transfer ◽  
Reynolds Numbers ◽  
Transfer Coefficients ◽  
Total Heat Transfer ◽  
Optimum Length ◽  
Trailing Edge ◽  
Heat Transfer Coefficients ◽  
Casting Technology ◽  
Nusselt Numbers ◽  
Pin Fins

Short pin fins are often used to increase the heat transfer to the coolant in the trailing edge of a turbine blade. Due primarily to limits of casting technology, it is not possible to manufacture pins of optimum length for heat transfer purposes in the trailing edge region. In many cases the pins are so short that they actually decrease the total heat transfer surface area compared to a plain wall. A heat transfer data base for these short pins is not available in the literature. Heat transfer coefficients on pin and endwall surfaces were measured for several staggered arrays of short pin fins. The measured Nusselt numbers when plotted versus Reynolds numbers were found to fall on a single curve for all surfaces tested. The heat transfer coefficients for the short pin fins (length to diameter ratios of 1/2 and 2) were found to be about a factor of two lower than data from the literature for longer pin arrays (length to diameter ratios of about 8).

Heat Transfer on Rotating Channel With Various Heights of Pin-Fin

2008 ◽  
Author(s):  
Jun Su Park ◽  
Kyung Min Kim ◽  
Dong Hyun Lee ◽  
Hyung Hee Cho ◽  
Minking K. Chyu
Keyword(s):  
Heat Transfer ◽  
Mass Transfer ◽  
Heat Mass Transfer ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Naphthalene Sublimation Technique ◽  
Pin Fins ◽  
Naphthalene Sublimation ◽  
Pin Fin Array

Pin-fins have been used to enhance the heat transfer near the trailing edge of a turbine airfoil. Previous pin-fin heat transfer studies focused mainly on the array geometry of pin height-to-diameter equal to unity in a stationary frame. This study experimentally examines the effects of pin height-to-diameter ratio (Hp/Dp) from 2 to 4 and rotation number (Ro) from 0 to 0.2. The tested model used a staggered pin-fin array with an inter-pin spacing of 2.5 times the pin-diameter (S/D = 2.5) in both longitudinal and transverse directions. Detailed heat/mass transfer coefficients were measured using the naphthalene sublimation technique with a heat-mass transfer analogy. The data measured suggest that an increase in Hp/Dp increases the level of array heat/mass transfer. Array averaged Sherwood numbers for Hp/Dp = 3 and Hp/Dp = 4 are approximately 10% and 35% higher than that of Hp/Dp = 2. The effect of rotation induces notable difference in heat/mass transfer between the leading surface and the trailing surface. The heat transfer coefficients change a little although the rotating number increases in the tested range because the pin-fins break the rotation-induced vortices.

Heat Transfer in Rotating, Trailing Edge, Converging Channels With Full and Partial Height Strip-Fins

2021 ◽  
Author(s):  
Izzet Sahin ◽  
I-Lun Chen ◽  
Lesley M. Wright ◽  
Je-Chin Han ◽  
Hongzhou Xu ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Pressure Drop ◽  
Flow Direction ◽  
Internal Cooling ◽  
Transfer Coefficients ◽  
Trailing Edge ◽  
Cooling Channels ◽  
Heat Transfer Coefficients ◽  
Pin Fins ◽  
Full Height

Abstract A wide variety of pin-fins have been used to enhance heat transfer in internal cooling channels. However, due to their large blockage in the flow direction, they result in an undesirable high pressure drop. This experimental study aims to reduce pressure drop while increasing the heat transfer surface area by utilizing strip-fins in converging internal cooling channels. The channel is designed with a trapezoidal cross-section, converges in both transverse and longitudinal directions, and is also skewed β = 120° with respect to the direction of rotation in order to model a trailing edge cooling channel. Only the leading and trailing surfaces of the channel are instrumented, and each surface is divided into eighteen isolated copper plates to measure the regionally averaged heat transfer coefficient. Utilizing pressure taps at the inlet and outlet of the channel, the pressure drop is obtained. Three staggered arrays of strip-fins are investigated: one full height configuration and two partial fin height arrangements (Sz = 2mm and 1mm). In all cases, the strip fins are 2mm wide (W) and 10mm long (Lf) in the flow direction. The fins are spaced such that Sy/Lf = 1 in the streamwise direction. However, due to the convergence the spanwise spacing Sx/W, was varied from 8 to 6.2 along the channel. The rotation number of the channel varied up to 0.21 by ranging the inlet Reynolds number from 10,000 to 40,000 and rotation speed from 0 to 300rpm. It is found that the full height strip-fin channel results in a more non-uniform spanwise heat transfer distribution than the partial height strip-fin channel. Both trailing and leading surface heat transfer coefficients are enhanced under rotation conditions. The 2mm height partial strip-fin channel provided the best thermal performance, and it is comparable to the performance of the converging channels with partial length circular pins. The strip-fin channel can be a design option when the pressure drop penalty is a major concern.

Combined Effects of Perforated Blockages and Pin Fins in a Trailing Edge Internal Cooling Duct

2014 ◽  
Author(s):  
Rui Kan ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Pressure Loss ◽  
Area Ratio ◽  
Combined Effects ◽  
Transfer Coefficients ◽  
Pin Fin ◽  
Heat Transfer Coefficients ◽  
Pin Fins ◽  
Pin Fin Arrays

Pin fin arrays and perforated blockages are both important methods for gas turbine trailing edge cooling. Perforated blockages result in higher heat transfer coefficients with larger pressure loss penalty. For enhanced heat transfer with medium pressure loss, we installed a perforated blockage at the inlet of pin fin arrays and studied the combined effects between impingement and pin fin. Heat transfer coefficients were measured with the transient liquid crystal method and the lumped capacitance model. Flow field was investigated using the RNG k-ε model. Six configurations with different flow area ratio, hole distribution and hole aspect ratio were examined at duct Reynolds number between 9,000 and 20,000. The results reveal that under impingement condition, Nusselt number for the first two rows of pin fins near the stagnation point is 2∼3 times larger than the baseline case without impingement. The most important parameter for heat transfer and friction loss is the area ratio. The average Nusselt number increases 20%∼50% with impingement, and the friction factor increases 4∼20 times. Heat transfer and friction loss for the combined configurations satisfy the correlation Nu = 0.1766Re0.702f0.188.

Sign in / Sign up

Export Citation Format

Share Document