scholarly journals An Experimental Study on Steel and Teflon Squeeze Film Dampers

2006 ◽  
Vol 13 (1) ◽  
pp. 33-40 ◽  
Author(s):  
Asad A. Khalid ◽  
A. Albagul ◽  
W. Faris ◽  
Godem A. Ismail
Keyword(s):  
Vibration Analysis ◽  
Vibration Amplitude ◽  
Pressure Gauge ◽  
Squeeze Film ◽  
Eccentricity Ratio ◽  
Test Rig ◽  
At Resonance ◽  
Squeeze Film Dampers ◽  
Rotor Support ◽  
Steel Damper

In this paper, the vibration analysis on Teflon and steel squeeze film dampers has been carried out. At different frequency ranges, vibration amplitude and the resonance frequency are measured. The eccentricity ratio at resonance speed has been determined. Results show that the vibration amplitude of the steel damper is 10% less at resonance compared with the Teflon damper. On the other hand, saving weight of 36% has been achieved by using the Teflon damper.A rotor bearing system for vibration analysis has been designed and fabricated. The test rig consists of mild steel shaft with two supports, oil pressure gauge system and two self-alignment ball bearings fixed on each end support. Two squeeze film dampers are used at each of the rotor support ends. Teflon and steel squeeze film dampers (SFD) were fabricated and tested using turning machine.

scholarly journals Experimental Investigation of the Dynamic Response of Squeeze Film Dampers Made of Steel and Glass/Epoxy

2008 ◽  
Vol 15 (6) ◽  
pp. 631-637 ◽  
Author(s):  
Waleed F. Faris ◽  
Asad A. Khalid ◽  
A. Albagul ◽  
Godem A. Ismail
Keyword(s):  
Vibration Amplitude ◽  
Epoxy Composite ◽  
Diameter Ratio ◽  
Squeeze Film ◽  
Test Rig ◽  
Pressure System ◽  
Squeeze Film Damper ◽  
Weight Saving ◽  
Squeeze Film Dampers ◽  
Steel Damper

This work is devoted to the fabrication and investigation of the Squeeze Film Dampers (SFDs) which are widely used in many applications. This include the fabrication of a test rig and several dampers with different sizes and two different materials which composite and non-composite. Composite dampers (Glass/epoxy), each consists of 30 layers, were fabricated by hand lay-up method. Outer and inner diameters of all the fabricated dampers were maintained as 60 and 40 mm respectively. Non-composite dampers (Steel) were fabricated and tested using turning machine. Three dampers of different lengths were examined for both materials. A rotor-bearing system for the analysis has been designed and fabricated. The test rig consists of mild steel shaft, two supports, oil pressure system, and two self-alignment ball bearings were fixed on each end support. Two squeeze film dampers were used for the two support ends. Vibration amplitude has been examined for all the fabricated dampers at different shaft rotational speeds. The first resonance speed was examined for all the dampers tested. Results show that the vibration amplitude of the steel damper was lower than Glass/epoxy dampers with the same L/D ratio. On the other hand, a considerable weight saving has been achieved by using Glass/epoxy composite dampers. It has been found that the performance of squeeze film damper improved with increasing length/diameter ratio (L/D) within the range tested.

Influence of different flow regimes on the performance characteristics of a four-pad hydrostatic squeeze film damper loaded between pads

2019 ◽  
Vol 71 (3) ◽  
pp. 440-446
Author(s):  
Amina Nemchi ◽  
Ahmed Bouzidane ◽  
Aboubakeur Benariba ◽  
Hicham Aboshighiba
Keyword(s):  
Turbulent Flow ◽  
Load Capacity ◽  
Flow Regimes ◽  
Performance Characteristics ◽  
Squeeze Film ◽  
Eccentricity Ratio ◽  
Flow Conditions ◽  
Content Type ◽  
Turbulent Flow Regime ◽  
Squeeze Film Dampers

Purpose The purpose of this paper is to study the influence of different flow regimes on the dynamic characteristics of four-pad hydrostatic squeeze film dampers (SFDs) loaded between pads. Design/methodology/approach A numerical model based on Constantinescu’s turbulent lubrication theory using the finite difference method has been developed and presented to study the effect of eccentricity ratio on the performance characteristics of four-pad hydrostatic SFDs under different flow regimes. Findings It was found that the influence of turbulent flow on the dimensionless damping of four-pad hydrostatic SFDs appears to be essentially controlled by the eccentricity ratio. It was also found that the laminar flow presents higher values of load capacity compared to bearings operating under turbulent flow conditions. Originality/value In fact, the results obtained show that the journal bearing performances are significantly influenced by the turbulent flow regime. The study is expected to be useful to bearing designers.

scholarly journals Imbalance Response of a Test Rotor Supported on Squeeze Film Dampers

1998 ◽  
Vol 120 (2) ◽  
pp. 397-404 ◽  
Author(s):  
L. San Andre´s ◽  
D. Lubell
Keyword(s):  
Chaotic Behavior ◽  
Nonlinear Behavior ◽  
Theoretical Models ◽  
Forced Response ◽  
Analytical Models ◽  
Squeeze Film ◽  
Test Rig ◽  
Critical Speeds ◽  
Highly Nonlinear ◽  
Squeeze Film Dampers

Squeeze film dampers (SFDs) provide vibration attenuation and structural isolation to aircraft gas turbine engines which must be able to tolerate larger imbalances while operating above one or more critical speeds. Rotor-bearing-SFD systems are regarded in theory as highly nonlinear, showing jump phenomena and even chaotic behavior for sufficiently large levels of rotor imbalance. Yet, few experimental results of practical value have verified the analytical predictions. A test rig for measurement of the dynamic forced response of a three-disk rotor (45 kg) supported on two cylindrical SFDs is described. The major objective is to provide a reliable data base to validate and enhance SFD design practice and to allow a direct comparison with analytical models. The open-ends SFD are supported by four-bar centering structures, each with a stiffness of 3.5 MN/m. Measured synchronous responses to 9000 rpm due to various imbalances show the rotor-SFD system to be well damped with amplification factors between 1.6 and 2.1 while traversing cylindrical and conical modes critical speeds. The rotor amplitudes of motion are found to be proportional to the imbalances for the first mode of vibration, and the damping coefficients extracted compare reasonably well to predictions based on the full-film, open-ends SFD. Tight lip (elastomeric) seals contribute greatly to the overall damping of the test rig. Measured dynamic pressures at the squeeze film lands are well above ambient values with no indication of lubricant dynamic cavitation as simple theoretical models dictate. The measurements show absence of nonlinear behavior of the rotor-SFD apparatus for the range of imbalances tested.

Analysis and Experimental Investigation of the Stability of Intershaft Squeeze Film Dampers—Part 2: Control of Instability

1978 ◽  
Vol 100 (3) ◽  
pp. 558-562 ◽  
Author(s):  
D. H. Hibner ◽  
P. N. Bansal ◽  
D. F. Buono
Keyword(s):  
Experimental Investigation ◽  
Stability Analysis ◽  
Shear Deformation ◽  
System Stability ◽  
Squeeze Film ◽  
Viscous Damper ◽  
Test Rig ◽  
Squeeze Film Dampers ◽  
Stability Maps ◽  
The Stability

The results of an analytical and experimental investigation showing the existence of an intershaft viscous damper instability were presented in reference [1]. In the present investigation, a more comprehensive stability analysis is used to study the stability of the test rig which incorporates a modified intershaft bearing support. The analysis is applicable to large multi-mass, rotor-bearing systems and includes the effects of gyroscopic moments, shear deformation, bearing support flexibility, and damping. The results of the stability analysis are presented in the form of system stability maps which clearly indicate the effectiveness of the modification in improving the instability onset speed of the system. Also presented are the results of an experimental investigation which substantiate the analytical predictions.

Effects of Adding a Central Groove to the Squeeze Film Damper Lands

2013 ◽  
Author(s):  
Praneetha Boppa ◽  
Aarthi Sekaran ◽  
Gerald Morrison
Keyword(s):  
Vibration Amplitude ◽  
High Speed ◽  
Dynamic Pressure ◽  
Aerospace Industry ◽  
Squeeze Film ◽  
Structural Components ◽  
Squeeze Film Damper ◽  
Pressure Profiles ◽  
Squeeze Film Dampers ◽  
Bearing System

Squeeze film dampers (SFDs) are used in the high speed turbo machinery industry and aerospace industry as a means to reduce vibration amplitude, to provide damping, to improve dynamic stability of the rotor bearing system and to isolate structural components. Past studies have not included effects of variation of the stator geometries in a squeeze film damper. A central groove added to the squeeze film land is hypothesized to provide a uniform flow source which theory predicts will result in forces less than one fourth of that seen in SFDs without a central groove. In the present study, 3D numerical simulations of SFDs with different size central grooves on the squeeze film land are performed to predict the variation of the dynamic pressure profiles. The numerical model and method have been validated via comparison to experimental data for a SFD without a central groove. When a central groove is added to the squeeze film land, the pressures generated are reduced to half of that generated when run without a central groove on the land. The amount of reduction in pressure values depends on the volume of the groove, not on the aspect ratio of the groove. Addition of a central groove reduces the pressures, rigidity developed in squeeze film land, and forces generated by squeeze film damper.

Nonlinear Vibration Analysis of a Dielectric Elastomer Based Microbeam Resonator

2016 ◽  
Vol 846 ◽  
pp. 188-192 ◽  
Author(s):  
Chuang Feng ◽  
Jie Yang ◽  
Liao Liang Ke
Keyword(s):  
Resonant Frequency ◽  
Dynamic Characteristics ◽  
Vibration Analysis ◽  
Vibration Amplitude ◽  
Ambient Pressure ◽  
Dielectric Elastomer ◽  
Squeeze Film ◽  
Beam Resonator ◽  
Squeeze Film Damping ◽  
Electrical Voltage

Dynamic characteristics of a dielectric elastomer based micro beam resonator are investigated by taking into consideration of squeeze-film damping, large deformation and electrical voltage. The analysis shows that the resonant frequency of the resonator can be tuned through changing applied electrical voltage. It is observed that the natural frequency of the resonator increases with the increase of the vibration amplitude. In addition, the ambient pressure can significantly alter the resonant frequency of the resonator. The analysis is envisaged to provide qualitative predictions and guidelines for design and application of DE-based micro resonators.

Rotordynamic Performance of Finite Length Squeeze Film Dampers

2003 ◽  
Author(s):  
A. El-Shafei ◽  
A. S. El-Kabbany
Keyword(s):  
Finite Length ◽  
Reynolds Equation ◽  
Squeeze Film ◽  
Rigid Rotor ◽  
Damping Coefficients ◽  
At Resonance ◽  
R Ratio ◽  
Squeeze Film Dampers ◽  
Current Design ◽  
Analytical Formulae

A recently developed finite length model of squeeze film dampers is extended and used in predicting the behavior of a rigid rotor supported by squeeze film dampers (SFDs). The model is based on a perturbation solution of Reynolds’ equation. The finite length SFD damping coefficients are presented for various L/R ratios. The effect of damper finite length is studied. Simulations of the behavior of a rigid rotor with the finite length SFDs illustrate the response of the roto-rbearing system. The accuracy of the finite damper model is shown for cases comparable to short and long dampers models. The short damper and long damper models are generally accepted to be valid for L/D < 1/4, and for L/D > 4, respectively. The capability of the finite length damper model to capture the main essence of the L/R ratio on the rotor response at resonance is illustrated. Analytical formulae for damping estimates are provided for finite length dampers. It is shown that the finite length damper actually provides less damping than either the short or the long damper models, which means that current design practices actually overestimate the SFD damping capabilities.

Experimental Investigation of the Effects of Squeeze Film Damper Design on Highspeed Rotor System

2020 ◽  
Author(s):  
Vincent Iacobellis ◽  
Kamran Behdinan ◽  
Dennis Chan ◽  
Dave Beamish
Keyword(s):  
Dynamic Testing ◽  
Operating Conditions ◽  
Squeeze Film ◽  
Test Rig ◽  
Oil Supply ◽  
Squeeze Film Dampers ◽  
Jeffcott Rotor ◽  
Large Amplitude Motions ◽  
Damper Design ◽  
Initial Results

Abstract Squeeze film dampers (SFDs) are used in highspeed rotordynamics systems to mitigate vibrations while traversing critical speeds. SFDs are critical in dissipating large amplitude motions and dynamic loading transferred from the rotor to the bearing supports during highspeed operation. Little testing on the effect of SFDs on rotor shafts under highspeed operating conditions is available in the literature. Thus, a SFD-rotor test rig has been designed and built to study the effect of SFD oil supply pressure, oil temperature, oil inlet feed number/orientation, unbalance, and seals on the response of a Jeffcott rotor. In this paper, the test rig is introduced along with its calibration through static and dynamic testing. It was found that the rotor displacement results were improved through the addition of trial masses to provide a runout correction and that using rubber supports for the support structure generated more symmetric results in the vertical and horizontal planes compared to steel supports. Initial results for the test rig are also presented for different unbalances with and without oil supply and with and without SFD end seals. In these cases, increased unbalance produced higher amplitude motion with a corresponding increase in critical speed and decrease in damping.

The influence of fluid inertia forces on the sudden unbalance responses of squeeze-film damper supported rotors

1998 ◽  
Vol 212 (5) ◽  
pp. 353-357 ◽  
Author(s):  
G Meng ◽  
Y-C Guo ◽  
E. J. Hahn
Keyword(s):  
Transient Process ◽  
Vibration Amplitude ◽  
Constant Speed ◽  
Squeeze Film ◽  
Flexible Rotor ◽  
Fluid Inertia ◽  
Transient Vibration ◽  
Squeeze Film Damper ◽  
Squeeze Film Dampers ◽  
Inertia Forces

The influence of fluid inertia on the sudden unbalance response of a flexible rotor supported on centralized and uncentralized squeeze-film dampers is investigated. Whether the rotor is at constant speed or accelerating, it was generally found that fluid inertia shortens the transient process and decreases the transient vibration amplitude. Qualitatively, the effect of fluid inertia is similar to increased damping.

Dynamic behavior analysis of a rigid rotor supported by hydrostatic squeeze film dampers compensated with new electrorheological valve restrictors

2019 ◽  
Vol 72 (5) ◽  
pp. 611-619 ◽  
Author(s):  
Mohamed Benadda ◽  
Ahmed Bouzidane ◽  
Marc Thomas ◽  
Raynald Guilbault
Keyword(s):  
Dynamic Behavior ◽  
High Speed ◽  
Nonlinear Models ◽  
Squeeze Film ◽  
Rigid Rotor ◽  
Eccentricity Ratio ◽  
Content Type ◽  
Squeeze Film Damper ◽  
Transmitted Force ◽  
Squeeze Film Dampers

Purpose This paper aims to propose a new hydrostatic squeeze film damper compensated with electrorheological valve restrictors to control the nonlinear dynamic behavior of a rigid rotor caused by high unbalance eccentricity ratio. To investigate the effect of electrorheological valve restrictors on the dynamic behavior of a rigid rotor, a nonlinear model is developed and presented. Design/methodology/approach The nonlinear results are compared with those obtained from a linear approach. The results show good agreement between the linear and nonlinear methods when the unbalanced force is small. The effects of unbalance eccentricity ratio and electric field on the vibration response and the bearing transmitted force are investigated using the nonlinear models. Findings The results of simulation performed that the harmonics generated by high unbalance eccentricities can be reduced by using hydrostatic squeeze film damper compensated with electrorheological valve restrictors. Originality/value The numerical results demonstrate that this type of smart hydrostatic squeeze film damper provides to hydrostatic designers a new bearing configuration suitable to control rotor vibrations and bearing transmitted forces, especially for high speed.

Sign in / Sign up

Export Citation Format

Share Document