scholarly journals Analysis of Multiaxis Vibration Simulators

1995 ◽  
Vol 2 (6) ◽  
pp. 461-470
Author(s):  
Norman Fitz-Coy
Keyword(s):  
Degrees Of Freedom ◽  
Mathematical Procedure ◽  
Singular Configurations ◽  
Corrective Measures ◽  
6 Degrees Of Freedom

A mathematical procedure that quantitatively addresses issues critical to the design and operation of multiaxis vibration simulators is presented. Both kinematic and dynamic issues are considered. The analysis is applied to both 3 and 6 degrees of freedom configurations. The existence of singular configurations is mentioned and appropriate corrective measures are recommended. A methodology for determining the required actuator commands is also presented.

Classification of Serial Robot-Manipulators with Nonremovable Singularities

1996 ◽  
Vol 118 (2) ◽  
pp. 202-208 ◽  
Author(s):  
A. Karger
Keyword(s):  
Degrees Of Freedom ◽  
Robot Manipulators ◽  
Removable Singularity ◽  
Singular Set ◽  
Singular Configurations ◽  
Serial Robot ◽  
Small Change ◽  
6 Degrees Of Freedom ◽  
4 Degrees Of Freedom

In this paper we discuss singular configurations of serial robot-manipulators with respect to their removability. A removable singularity is a singularity which can be removed from a motion of the end-effector by a small change of the motion. The most interesting situation appears for robot-manipulators with 5 degrees of freedom, because the case of 4 degrees of freedom is easy and singular configurations of robot-manipulators with 6 degrees of freedom are nonremovable. In the paper we give the complete list of all 5R robot-manipulators which have nonremovable singularities. The image of the singular set in the parameter space for such manipulators can be a plane, a quadric, a cylinder or an algebraic surface of degree 3 or 7. All of them are explicitly given.

4D in in vivo 2-photon laser scanning fluorescence microscopy with sample motion in 6 degrees of freedom

2011 ◽  
Vol 200 (1) ◽  
pp. 47-53 ◽  
Author(s):  
Sabine Scheibe ◽  
Mario M. Dorostkar ◽  
Christian Seebacher ◽  
Rainer Uhl ◽  
Frank Lison ◽  
...  
Keyword(s):  
Fluorescence Microscopy ◽  
Laser Scanning ◽  
Degrees Of Freedom ◽  
Sample Motion ◽  
6 Degrees Of Freedom

Workspace, dexterity and dimensional optimization of microhexapod

2015 ◽  
Vol 35 (4) ◽  
pp. 341-347 ◽  
Author(s):  
E. Rouhani ◽  
M. J. Nategh
Keyword(s):  
Degrees Of Freedom ◽  
Optimization Problem ◽  
Screw Theory ◽  
Design Parameters ◽  
Dimensional Synthesis ◽  
Content Type ◽  
Workspace Analysis ◽  
The Difference ◽  
Flexure Joints ◽  
6 Degrees Of Freedom

Purpose – The purpose of this paper is to study the workspace and dexterity of a microhexapod which is a 6-degrees of freedom (DOF) parallel compliant manipulator, and also to investigate its dimensional synthesis to maximize the workspace and the global dexterity index at the same time. Microassembly is so essential in the current industry for manufacturing complicated structures. Most of the micromanipulators suffer from their restricted workspace because of using flexure joints compared to the conventional ones. In addition, the controllability of micromanipulators inside the whole workspace is very vital. Thus, it is very important to select the design parameters in a way that not only maximize the workspace but also its global dexterity index. Design/methodology/approach – Microassembly is so essential in the current industry for manufacturing complicated structures. Most of the micromanipulators suffer from their restricted workspace because of using flexure joints compared to the conventional ones. In addition, the controllability of micromanipulators inside the whole workspace is very vital. Thus, it is very important to select the design parameters in a way that not only maximize the workspace but also its global dexterity index. Findings – It has been shown that the proposed procedure for the workspace calculation can considerably speed the required calculations. The optimization results show that a converged-diverged configuration of pods and an increase in the difference between the moving and the stationary platforms’ radii cause the global dexterity index to increase and the workspace to decrease. Originality/value – The proposed algorithm for the workspace analysis is very important, especially when it is an objective function of an optimization problem based on the search method. In addition, using screw theory can simply construct the homogeneous Jacobian matrix. The proposed methodology can be used for any other micromanipulator.

An improved calibration curve between soil pH measured in waterand CaCl2

Soil Research ◽  
2002 ◽  
Vol 40 (8) ◽  
pp. 1399 ◽  
Author(s):  
B. L. Henderson ◽  
E. N. Bui
Keyword(s):  
Statistical Analysis ◽  
Water Resources ◽  
Soil Ph ◽  
Calibration Curve ◽  
Smooth Function ◽  
Degrees Of Freedom ◽  
Additive Model ◽  
Smoothing Spline ◽  
Look Up Table ◽  
6 Degrees Of Freedom

A new pH water to pH CaCl2 calibration curve was derived from data pooled from 2 National Land and Water Resources Audit projects. A total of 70465 observations with both pH in water and pH in CaCl2 were available for statistical analysis. An additive model for pH in CaCl2 was fitted from a smooth function of pH in water created by a smoothing spline with 6 degrees of freedom. This model appeared stable outside the range of the data and performed well (R2 = 96.2, s = 0.24). The additive model for conversion of pHw to pHCa is sigmoidal over the range of pH 2.5 to 10.5 and is similar in shape to earlier models. Using this new model, a look-up table for converting pHw to pHCa was created.

Radiation-tolerant robotic complex URS-2

2021 ◽  
Vol 9 (2) ◽  
pp. 142-150
Author(s):  
Ivan Guschin ◽  
Anton Leschinskiy ◽  
Andrey Zhukov ◽  
Alexander Zarukin ◽  
Vyacheslav Kiryukhin ◽  
...  
Keyword(s):  
Degrees Of Freedom ◽  
Force Feedback ◽  
Control Device ◽  
Control Panel ◽  
Original Design ◽  
Innovative Methods ◽  
Control Computer ◽  
Robotic Arm Control ◽  
6 Degrees Of Freedom ◽  
Radiation Tolerant

The results of the development of a radiation-tolerant robotic complex URS-2 for operation in hot cells at nuclear enterprises are presented. The robotic complex consists of several original components: robotic arm, control device with force feedback, control panel with hardware buttons and touch screen, control computer with system and application software, control-and-power cabinet. The robotic manipulator has 6 degrees of freedom, replaceable pneumatic grippers and is characterized by high radiation tolerance, similar to that of mechanical master-slave manipulators. The original design of the control device based on the delta-robot model that implements a copying mode of manual control of the robotic complex with force feedback is presented. The hardware and software solutions developed has made it possible to create a virtual simulator of the RTC for testing innovative methods of remote control of the robot, as well as teaching operators to perform technological tasks in hot cells. The experimental model of the robotic complex has demonstrated the ability to perform basic technological tasks in a demo hot cell, both in manual and automatic modes.

Sign in / Sign up

Export Citation Format

Share Document