Deposition Mechanism of Silicon Nitride in Direct Photoassisted Chemical Vapor Deposition Using a Low‐Pressure Hg Lamp

1995 ◽  
Vol 142 (6) ◽  
pp. 1976-1982 ◽  
Author(s):  
Masahiro Yoshimoto ◽  
Kenji Takubo ◽  
Tetsuya Ohtsuki ◽  
Michio Komoda ◽  
Hiroyuki Matsunami
Keyword(s):  
Chemical Vapor Deposition ◽  
Silicon Nitride ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Low Pressure ◽  
Deposition Mechanism

High temperature and low pressure chemical vapor deposition of silicon nitride on AlGaN: Band offsets and passivation studies

2016 ◽  
Vol 119 (14) ◽  
pp. 145702 ◽  
Author(s):  
Pramod Reddy ◽  
Shun Washiyama ◽  
Felix Kaess ◽  
M. Hayden Breckenridge ◽  
Luis H. Hernandez-Balderrama ◽  
...  
Keyword(s):  
Chemical Vapor Deposition ◽  
High Temperature ◽  
Silicon Nitride ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Low Pressure ◽  
Band Offsets ◽  
Pressure Chemical

In Situ Contamination Control Investigation of Silicon Nitride Low Pressure Chemical Vapor Deposition Process in Vertical Thermal Reactors

1992 ◽  
Vol 259 ◽  
Author(s):  
Mansour Moinpour ◽  
K. Bohannan ◽  
M. Shenasa ◽  
A. Sharif ◽  
G. Guzzo ◽  
...  
Keyword(s):  
Chemical Vapor Deposition ◽  
Silicon Nitride ◽  
Process Parameters ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Low Pressure ◽  
Nitride Film ◽  
Silicon Nitride Film ◽  
Contamination Control ◽  
Pressure Chemical

ABSTRACTA contamination control study of a Silicon Valley Group Thermco Systems Vertical Thermal Reactor(VTR) is presented. Trace elements of contaminants such as water vapor and oxygen have been shown to significantly affect the integrity of the silicon nitride film deposited by the low pressure chemical vapor deposition (LPCVD) process. This study documented the effects of process parameters on gaseous contamination levels, i.e., O2 and H2O vapor. Starting with a baseline process, the effects of an excursion of pre-deposition temperature ramp-up and stabilization condition, wafer load/unload and various post deposition conditions were explored. An axial profile of moisture and oxygen levels along the wafer load was obtained using Linde's Low Pressure Reactor Analysis(LPRAS) methodology. In addition, other process parameters such as gas flow rates during load and unload of wafers, pre-deposition N2 purge and process tube exposure time to ambient environment were- investigated. The wafers were analyzed for contaminants on the wafer surface or in the deposited silicon nitride film using FTIR and Auger spectroscopy techniques. They showed low levels of Si-O and no measurable Si-H or N-H bonds.

Low pressure chemical vapor deposition of silicon nitride using the environmentally friendly tris(dimethylamino)silane precursor

1996 ◽  
Vol 11 (6) ◽  
pp. 1483-1488 ◽  
Author(s):  
R. A. Levy ◽  
X. Lin ◽  
J. M. Grow ◽  
H. J. Boeglin ◽  
R. Shalvoy
Keyword(s):  
Chemical Vapor Deposition ◽  
Silicon Nitride ◽  
Vapor Deposition ◽  
Chemical Vapor ◽  
Low Pressure ◽  
Environmentally Benign ◽  
Silicon Nitride Films ◽  
Pressure Chemical ◽  
Phase Nucleation ◽  
Silane Precursor

This study investigates the use of the environmentally benign precursor tri(dimethylamino)silane (TDMAS) with NH3 to synthesize silicon nitride films by low pressure chemical vapor deposition. The growth kinetics are investigated as a function of deposition temperature, total pressure, and NH3/TDMAS flow ratios. The deposits are found to be essentially stoichiometric and to contain ∼5 at. % carbon when appropriate NH3 concentrations are present. The films are found in all cases to be amorphous and highly tensile. For optimized processing conditions, values of the refractive index are close to those reported for Si3N4. The film density is observed to increase with higher deposition temperatures up to 800 °C and then decrease due to the onset of gas phase nucleation effects. This behavior is readily reflected in the etch rate of those films. FTIR spectra reveal the presence of hydrogen even at high deposition temperatures (900 °C). Hardness and Young's modulus of the films are seen to increase with higher deposition temperatures, reaching saturation values near 20 and 185 GPa, respectively, above 800 °C.

Sign in / Sign up

Export Citation Format

Share Document