scholarly journals The Effect of Pre-Heat Treatment of AluChrom 318 on the Corrosion Behaviour and Cr Evaporation in SOFC Cathode Air Pre-Heater

2019 ◽  
Vol 91 (1) ◽  
pp. 2253-2260
Author(s):  
Kun Zhang ◽  
Ahmad El-kharouf ◽  
Robert Steinberger-Wilckens
Keyword(s):  
Heat Treatment ◽  
Corrosion Behaviour ◽  
Sofc Cathode ◽  
Cr Evaporation

Effect of heat treatment on corrosion behaviour of deposited Fe–40Al intermetallics

2001 ◽  
Vol 36 (1) ◽  
pp. 65-69 ◽  
Author(s):  
J.G. Gonzalez-Rodriguez ◽  
M. Casales ◽  
M. Amaya ◽  
L. Martinez
Keyword(s):  
Heat Treatment ◽  
Corrosion Behaviour

Effect of homogenization temperature and soaking time on the microstructure and corrosion properties of a twin roll casted AA3003

CORROSION ◽  
10.5006/3813 ◽  
2021 ◽  
Author(s):  
Donovan Verkens ◽  
Reynier Revilla ◽  
Mert Günyüz ◽  
Cemil Işıksaçan ◽  
Herman Terryn ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Heat Exchangers ◽  
Corrosion Behaviour ◽  
Life Time ◽  
Homogenization Temperature ◽  
Corrosion Properties ◽  
Cross Sectional ◽  
The Impact ◽  
Twin Roll

The AA3003 alloy is widely used as fin material in heat exchangers. The life time of these heat exchangers is mostly determined by their corrosion properties. Twin roll casting (TRC) of AA3003 material is known to often result in the formation of a macrosegregation area of alloying elements towards the centre plane of the casted strip (centre line segregation = CLS). Considering the potential exposure of cross-sectional areas of TRC material in the heat exchanger fin application, and the relatively high corrosion susceptibility of the CLS, the study of this region is of key importance to understand the microstructural effects on the resulting corrosion mechanisms and kinetics for these materials. Typically the alloys are homogenized to bring the microstructures closer to an equilibrium state, but the impact of this heat treatment on the corrosion properties is insufficiently studied. Therefore, this study investigates the effect of different homogenization procedures on the corrosion properties of the CLS and the interaction of the intermetallic particles with the surrounding aluminium matrix. This work shows that the pitting corrosion resistance is greatly dependent on the homogenization temperature, with better corrosion resistance obtained with higher temperature, especially near the CLS. This difference in corrosion behaviour is completely attributed to a difference in microstructure and not to an oxide layer effect. Furthermore, it is observed that not only temperature will have a large influence on the corrosion resistance, but duration of the heat treatment as well.

Corrosion behavior of heat-treated and cryorolled Al 5052 alloys in different chloride ion concentrations

2020 ◽  
Vol 67 (1) ◽  
pp. 7-15 ◽  
Author(s):  
Anasyida Abu Seman ◽  
Ji Kit Chan ◽  
Muhammad Anas Norazman ◽  
Zuhailawati Hussain ◽  
Dhindaw Brij ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Behaviour ◽  
Solution Treatment ◽  
Chloride Ion ◽  
Optical Microscope ◽  
Al Alloy ◽  
Content Type ◽  
Ion Concentrations ◽  
Heat Treated ◽  
Chloride Environment

Purpose This paper aims to investigate the corrosion behaviour of heat-treated and cryorolled Al 5052 alloys in different Cl− ion concentrations. Design/methodology/approach NaCl solutions with concentrations of 0, 0.5, 3.5 and 5.5 per cent were selected. Samples were subjected to pre-heat treatment (annealing at 300 °C and solution treatment at 540 °C) and cryorolling up to 30 per cent reduction before undergoing corrosion tests. The corrosion behaviour of the samples was then investigated by potentiodynamic polarization. The microstructure of the corroded samples was evaluated under an optical microscope, and the percentages of pits on their surfaces were calculated. Findings The cryorolled samples had a lower corrosion rate than the samples that were not cryorolled. The cryorolled sample that underwent solution treatment showed the highest corrosion resistance among all the samples tested. Practical implications The commercial impact of the study is the possibility of using the cryorolled Al alloy in various ion chloride environment. Originality/value The obtained results help in understanding the corrosion behaviour of cryorolled samples under different heat treatment conditions.

Heat treatment effect on the corrosion behaviour of black passivated ZnNi alloys

2005 ◽  
Vol 47 (2) ◽  
pp. 307-321 ◽  
Author(s):  
C. Müller ◽  
M. Sarret ◽  
E. Garcı́a
Keyword(s):  
Heat Treatment ◽  
Treatment Effect ◽  
Corrosion Behaviour
Sign in / Sign up

Export Citation Format

Share Document