Nonlinear Dynamic Analysis of Beck’s Problem by Using Simple Models

1983 ◽  
Vol 7 (2) ◽  
pp. 65-75
Author(s):  
H. Ohmori ◽  
Y. Hangai ◽  
H. Tanaka
Keyword(s):  
Finite Element ◽  
Numerical Analysis ◽  
Finite Element Model ◽  
Dynamic Analysis ◽  
Nonlinear Dynamic ◽  
Degrees Of Freedom ◽  
Nonlinear Dynamic Analysis ◽  
Element Model ◽  
Mechanical Models ◽  
Lateral Displacements

This paper deals with a nonlinear, dynamic analysis of Beck’s rod, trying to explain discrepancies between analysis and experiment and taking axial and lateral displacements of the rod into account. The numerical analysis was carried out for discrete mechanical models of the rod involving four and eight degrees-of-freedom as well as for a finite element model. Results obtained were thoroughly discussed and compared with known results stemming from previous linear treatments of Beck’s rod.

Finite Element Model of the Human Knee Joint to Study Tibio-Femoral Contact Mechanics

2000 ◽  
Author(s):  
Tammy Haut Donahue ◽  
Maury L. Hull ◽  
Mark M. Rashid ◽  
Christopher R. Jacobs
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Degrees Of Freedom ◽  
Soft Tissues ◽  
Element Model ◽  
Human Knee ◽  
Human Knee Joint ◽  
Solid Models ◽  
Flexion Extension ◽  
A New Technique

Abstract A finite element model of the tibio-femoral joint in the human knee was created using a new technique for developing accurate solid models of soft tissues (i.e. cartilage and menisci). The model was used to demonstrate that constraining rotational degrees of freedom other than flexion/extension when the joint is loaded in compression markedly affects the load distribution between the medial and lateral sides of the joint. The model also was used to validate the assumption that the bones can be treated as rigid.

Modeling of fast pre-joining processes optimization for skin-stringer panels

2014 ◽  
Vol 34 (4) ◽  
pp. 323-332 ◽  
Author(s):  
Gang Liu ◽  
Wei Tang ◽  
Ying-Lin Ke ◽  
Qing-Liang Chen ◽  
Yunbo Bi
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Degrees Of Freedom ◽  
Traditional Approach ◽  
Element Model ◽  
Optimal Number ◽  
Neighborhood Search ◽  
Adaptive Genetic Algorithm ◽  
Time Saving ◽  
Content Type

Purpose – The purpose of this paper is to propose a new model for optimizing pre-joining processes quickly and accurately, guiding workers to standardized operations. For the automatic riveting in panel assemblies, the traditional approach of determination of pre-joining processes entirely rests on the experience of workers, which leads to the improper number, location and sequence of pre-joining, the low quality stability and the high repair rate in most cases. Design/methodology/approach – The clearances computation with the complete finite element model for every process combination is time-consuming. Therefore a fast pre-joining processes optimization model (FPPOM) is proposed. This model treats both the measured initial clearances and the stiffness matrices of key points of panels as an input; considers the permissive clearances as an evaluation criterion; regards the optimal number, location and sequence as an objective; and takes the neighborhood-search-based adaptive genetic algorithm as a solution. Findings – A comparison between the FPPOM and complete finite element model with clearances (CFEMC) was made in practice. Further, the results indicate that running the FPPOM is time-saving by >90 per cent compared with the CFEMC. Practical implications – This paper provides practical insights into realizing the pre-joining processes optimization quickly. Originality/value – This paper is the first to propose the FPPOM, which could simplify the processes, reduce the degrees of freedom of nodes and conduct the manufacturers to standardized manipulations.

Sign in / Sign up

Export Citation Format

Share Document