Controlling the destructive effects of clay – organic liquid interactions, by application of effective stresses

1991 ◽  
Vol 28 (3) ◽  
pp. 388-398 ◽  
Author(s):  
Federico Fernandez ◽  
Robert M. Quigley
Keyword(s):  
Hydraulic Conductivity ◽  
Effective Stress ◽  
Organic Liquid ◽  
Critical Role ◽  
Water Soluble ◽  
Practical Significance ◽  
Organic Liquids ◽  
Effective Stresses ◽  
Chemically Induced ◽  
Clay Barrier

The magnitude of the effective stresses acting on a clay barrier appear to play a critical role in preserving low hydraulic conductivity, k, during exposure to soluble organic liquids. This paper summarizes the results of a research study on a natural clay from southwestern Ontario permeated with various mixtures of landfill leachate and water-soluble organic liquids at effective stresses ranging from 0 to ~300 kPa. Laboratory testing of "unconfined", water-compacted clays indicated that municipal solid waste leachates containing ethanol and dioxane at concentrations in excess of 70% can cause damaging increases in k of up to 1000-fold. Predamage application of vertical effective stresses can reduce or even eliminate these increases in k because of chemically induced consolidation and closure of macropores that develop as a result of double layer collapse. The levels of static effective stress required to prevent the increases in k were much higher for nonpolar dioxane (> 160 kPa) than for intermediately polar ethanol (20–40 kPa). Postdamage application of static effective stresses successfully eliminated the increases in k produced by ethanol permeation at near zero stress but could not heal the clay damaged by permeation of nonpolar dioxane. The practical significance of this work is discussed relative to clay barrier design. Key words: hydraulic conductivity, clay, organic liquids, leachate, liner, effective stress healing.

Viscosity and dielectric constant controls on the hydraulic conductivity of clayey soils permeated with water-soluble organics

1988 ◽  
Vol 25 (3) ◽  
pp. 582-589 ◽  
Author(s):  
F. Fernandez ◽  
R. M. Quigley
Keyword(s):  
Dielectric Constant ◽  
Hydraulic Conductivity ◽  
Double Layer ◽  
Pore Space ◽  
Water Soluble ◽  
Organic Liquids ◽  
Clayey Soils ◽  
Compacted Clay ◽  
High Concentrations ◽  
Water Saturated

Water-soluble organic liquids may, under some circumstances, dramatically increase the hydraulic conductivity, k, of water-saturated clayey soils, thus destroying their effectiveness as barriers for contaminants. Double-layer contraction at constant void ratio with resultant increases in the pore space available for flow has been identified as a primary mechanism for such increases in k. This paper shows, however, that the increased viscosity of solutions of some organics in water results in significant decreases in k.Pure alcohols (ethanol and methanol) and other water solubles (dioxane) when permeated through water-compacted clay samples produce an initial decrease in k, followed by a gradual increase to equilibrium values. The "hydrocarbon" front raises the viscosity of the pore fluid and causes an initial drop in k. Tests using aqueous solutions of ethanol and dioxane show decreases in k at concentrations up to ~70%. Only at high concentrations does the dielectric constant, double-layer effect overcome the viscosity effect and produce net increases in k.Effective stresses σ′vof 160 kPa during permeation with ethanol and dioxane prevent the increases in k. Physicochemically induced consolidation and increased K0-shearing effects that close shrinkage cracks are operative. Key words: hydraulic conductivity, liquid hydrocarbons, clay, viscosity, dielectric constant.

A comparative study on methods for determining the hydraulic properties of a clay shale

2020 ◽  
Vol 224 (3) ◽  
pp. 1523-1539
Author(s):  
Lisa Winhausen ◽  
Alexandra Amann-Hildenbrand ◽  
Reinhard Fink ◽  
Mohammadreza Jalali ◽  
Kavan Khaledi ◽  
...  
Keyword(s):  
Pore Pressure ◽  
Effective Stress ◽  
Ion Beam ◽  
Applied Pressure ◽  
Pressure Oscillation ◽  
Stress Conditions ◽  
Data Set ◽  
Clay Shale ◽  
Permeability Coefficients ◽  
Effective Stresses

SUMMARY A comprehensive characterization of clay shale behavior requires quantifying both geomechanical and hydromechanical characteristics. This paper presents a comparative laboratory study of different methods to determine the water permeability of saturated Opalinus Clay: (i) pore pressure oscillation, (ii) pressure pulse decay and (iii) pore pressure equilibration. Based on a comprehensive data set obtained on one sample under well-defined temperature and isostatic effective stress conditions, we discuss the sensitivity of permeability and storativity on the experimental boundary conditions (oscillation frequency, pore pressure amplitudes and effective stress). The results show that permeability coefficients obtained by all three methods differ less than 15 per cent at a constant effective stress of 24 MPa (kmean = 6.6E-21 to 7.5E-21 m2). The pore pressure transmission technique tends towards lower permeability coefficients, whereas the pulse decay and pressure oscillation techniques result in slightly higher values. The discrepancies are considered minor and experimental times of the techniques are similar in the range of 1–2 d for this sample. We found that permeability coefficients determined by the pore pressure oscillation technique increase with higher frequencies, that is oscillation periods shorter than 2 hr. No dependence is found for the applied pressure amplitudes (5, 10 and 25 per cent of the mean pore pressure). By means of experimental handling and data density, the pore pressure oscillation technique appears to be the most efficient. Data can be recorded continuously over a user-defined period of time and yield information on both, permeability and storativity. Furthermore, effective stress conditions can be held constant during the test and pressure equilibration prior to testing is not necessary. Electron microscopic imaging of ion-beam polished surfaces before and after testing suggests that testing at effective stresses higher than in situ did not lead to pore significant collapse or other irreversible damage in the samples. The study also shows that unloading during the experiment did not result in a permeability increase, which is associated to the persistent closure of microcracks at effective stresses between 24 and 6 MPa.

scholarly journals Comparative Metabolite Profile, Biological Activity and Overall Quality of Three Lettuce (Lactuca sativa L., Asteraceae) Cultivars in Response to Sulfur Nutrition

Pharmaceutics ◽  
2021 ◽  
Vol 13 (5) ◽  
pp. 713
Author(s):  
Muna Ali Abdalla ◽  
Fengjie Li ◽  
Arlette Wenzel-Storjohann ◽  
Saad Sulieman ◽  
Deniz Tasdemir ◽  
...  
Keyword(s):  
Secondary Metabolites ◽  
Plant Growth ◽  
Sesquiterpene Lactones ◽  
Critical Role ◽  
Soluble Sugars ◽  
Radical Scavenging ◽  
Metabolite Profile ◽  
Water Soluble ◽  
Radical Scavenger ◽  
Higher Plant

The main objective of the present study was to assess the effects of sulfur (S) nutrition on plant growth, overall quality, secondary metabolites, and antibacterial and radical scavenging activities of hydroponically grown lettuce cultivars. Three lettuce cultivars, namely, Pazmanea RZ (green butterhead, V1), Hawking RZ (green multi-leaf lettuce, V2), and Barlach RZ (red multi-leaf, V3) were subjected to two S-treatments in the form of magnesium sulfate (+S) or magnesium chloride (−S). Significant differences were observed under −S treatments, especially among V1 and V2 lettuce cultivars. These responses were reflected in the yield, levels of macro- and micro-nutrients, water-soluble sugars, and free inorganic anions. In comparison with the green cultivars (V1 and V2), the red-V3 cultivar revealed a greater acclimation to S starvation, as evidenced by relative higher plant growth. In contrast, the green cultivars showed higher capabilities in production and superior quality attributes under +S condition. As for secondary metabolites, sixteen compounds (e.g., sesquiterpene lactones, caffeoyl derivatives, caffeic acid hexose, 5-caffeoylquinic acid (5-OCQA), quercetin and luteolin glucoside derivatives) were annotated in all three cultivars with the aid of HPLC-DAD-MS-based untargeted metabolomics. Sesquiterpene lactone lactucin and anthocyanin cyanidin 3-O-galactoside were only detected in V1 and V3 cultivars, respectively. Based on the analyses, the V3 cultivar was the most potent radical scavenger, while V1 and V2 cultivars exhibited antibacterial activity against Staphylococcus aureus in response to S provision. Our study emphasizes the critical role of S nutrition in plant growth, acclimation, and nutritional quality. The judicious-S application can be adopted as a promising antimicrobial prototype for medical applications.

scholarly journals A non-toxic, reversibly released imaging probe for oral cancer that is derived from natural compounds

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Magda Ghanim ◽  
Nicola Relitti ◽  
Gavin McManus ◽  
Stefania Butini ◽  
Andrea Cappelli ◽  
...  
Keyword(s):  
Oral Cancer ◽  
Cancer Progression ◽  
Intraoperative Imaging ◽  
Critical Role ◽  
Water Soluble ◽  
Stem Cell Marker ◽  
Squamous Cells ◽  
Tissue Identification ◽  
Tumorigenic Potential ◽  
The Impact

AbstractCD44 is emerging as an important receptor biomarker for various cancers. Amongst these is oral cancer, where surgical resection remains an essential mode of treatment. Unfortunately, surgery is frequently associated with permanent disfigurement, malnutrition, and functional comorbidities due to the difficultly of tumour removal. Optical imaging agents that can guide tumour tissue identification represent an attractive approach to minimising the impact of surgery. Here, we report the synthesis of a water-soluble fluorescent probe, namely HA-FA-HEG-OE (compound 1), that comprises components originating from natural sources: oleic acid, ferulic acid and hyaluronic acid. Compound 1 was found to be non-toxic, displayed aggregation induced emission and accumulated intracellularly in vesicles in SCC-9 oral squamous cells. The uptake of 1 was fully reversible over time. Internalization of compound 1 occurs through receptor mediated endocytosis; uniquely mediated through the CD44 receptor. Uptake is related to tumorigenic potential, with non-tumorigenic, dysplastic DOK cells and poorly tumorigenic MCF-7 cells showing only low intracellular levels and highlighting the critical role of endocytosis in cancer progression and metastasis. Together, the recognised importance of CD44 as a cancer stem cell marker in oral cancer, and the reversible, non-toxic nature of 1, makes it a promising agent for real time intraoperative imaging.

scholarly journals Stress sensitivity of porosity and permeability under varying hydrostatic stress conditions for different carbonate rock types of the geothermal Malm reservoir in Southern Germany

2021 ◽  
Vol 9 (1) ◽  
Author(s):  
Daniel Bohnsack ◽  
Martin Potten ◽  
Simon Freitag ◽  
Florian Einsiedl ◽  
Kai Zosseder
Keyword(s):  
Effective Stress ◽  
Hydraulic Properties ◽  
Rock Strength ◽  
Pore Network ◽  
Stress Sensitivity ◽  
Stress Conditions ◽  
Rock Matrix ◽  
Effective Stresses ◽  
Rock Types ◽  
Porosity And Permeability

AbstractIn geothermal reservoir systems, changes in pore pressure due to production (depletion), injection or temperature changes result in a displacement of the effective stresses acting on the rock matrix of the aquifer. To compensate for these intrinsic stress changes, the rock matrix is subjected to poroelastic deformation through changes in rock and pore volume. This in turn may induce changes in the effective pore network and thus in the hydraulic properties of the aquifer. Therefore, for the conception of precise reservoir models and for long-term simulations, stress sensitivity of porosity and permeability is required for parametrization. Stress sensitivity was measured in hydrostatic compression tests on 14 samples of rock cores stemming from two boreholes of the Upper Jurassic Malm aquifer of the Bavarian Molasse Basin. To account for the heterogeneity of this carbonate sequence, typical rock and facies types representing the productive zones within the thermal reservoir were used. Prior to hydrostatic investigations, the hydraulic (effective porosity, permeability) and geomechanical (rock strength, dynamic, and static moduli) parameters as well as the microstructure (pore and pore throat size) of each rock sample were studied for thorough sample characterization. Subsequently, the samples were tested in a triaxial test setup with effective stresses of up to 28 MPa (hydrostatic) to simulate in-situ stress conditions for depths up to 2000 m. It was shown that stress sensitivity of the porosity was comparably low, resulting in a relative reduction of 0.7–2.1% at maximum effective stress. In contrast, relative permeability losses were observed in the range of 17.3–56.7% compared to the initial permeability at low effective stresses. Stress sensitivity coefficients for porosity and permeability were derived for characterization of each sample and the different rock types. For the stress sensitivity of porosity, a negative correlation with rock strength and a positive correlation with initial porosity was observed. The stress sensitivity of permeability is probably controlled by more complex processes than that of porosity, where the latter is mainly controlled by the compressibility of the pore space. It may depend more on the compaction of precedented flow paths and the geometry of pores and pore throats controlling the connectivity within the rock matrix. In general, limestone samples showed a higher stress sensitivity than dolomitic limestone or dolostones, because dolomitization of the rock matrix may lead to an increasing stiffness of the rock. Furthermore, the stress sensitivity is related to the history of burial diagenesis, during which changes in the pore network (dissolution, precipitation, and replacement of minerals and cements) as well as compaction and microcrack formation may occur. This study, in addition to improving the quality of input parameters for hydraulic–mechanical modeling, shows that hydraulic properties in flow zones largely characterized by less stiff, porous limestones can deteriorate significantly with increasing effective stress.

Synthesis of aligned carbon nanotubes in organic liquids

2002 ◽  
Vol 17 (9) ◽  
pp. 2457-2464 ◽  
Author(s):  
Yafei Zhang ◽  
Mikka N.-Gamo ◽  
Kiyoharu Nakagawa ◽  
Toshihiro Ando
Keyword(s):  
Carbon Nanotubes ◽  
Organic Liquid ◽  
Film Surface ◽  
Normal Pressure ◽  
Organic Liquids ◽  
X Ray Diffraction ◽  
Multiwalled Carbon ◽  
Aligned Carbon Nanotubes ◽  
Novel Method ◽  
The Right

A simple and novel method was developed for efficient synthesis of aligned multiwalled carbon nanotubes (CNTs) in methanol and ethanol under normal pressure. The CNTs' alignment and structures were investigated using Raman scattering and x-ray diffraction spectroscopy. A unique kind of coupled CNT was synthesized in which one rotated to the left and one rotated to the right. Chains periodically bridged the coupled CNTs. The growth mechanism of the CNTs within organic liquid is proposed to be a catalytic process at the Fe film surface in a dynamic and thermal nonequilibrium condition in organic liquids.

Estimation of the fluid-fluid interfacial area using kinetic interface sensitive tracers in dynamic porous media experiments

2021 ◽  
Author(s):  
Alexandru Tatomir ◽  
Huhao Gao ◽  
Hiwa Abdullah ◽  
Martin Sauter
Keyword(s):  
Porous Medium ◽  
Porous Media ◽  
Two Phase Flow ◽  
Organic Liquid ◽  
Column Experiment ◽  
Interfacial Area ◽  
Breakthrough Curves ◽  
Water Soluble ◽  
Phase Flow ◽  
Two Phase

<p>Fluid-fluid interfacial area (IFA) in a two-phase flow in porous media is an important parameter for many geoscientific applications involving mass- and energy-transfer processes between the fluid-phases. Schaffer et al. (2013) introduced a new category of reactive tracers termed kinetically interface sensitive (KIS) tracers, able to quantify the size of the fluid-fluid IFA. In our previous experiments (Tatomir et al., 2018) we have demonstrated the application of the KIS tracers in a highly-controlled column experiment filled with a well-characterized porous medium consisting of well-sorted, spherical glass beads.</p><p>In this work we investigate several types of glass-bead materials and natural sands to quantitatively characterize the influence of the porous-medium grain-, pore-size and texture on the mobile interfacial area between an organic liquid and water. The fluid-fluid interfacial area is determined by interpretation of the breakthrough curves (BTCs) of the reaction product of the KIS tracer. When the tracer which is dissolved in the non-wetting phase meets the water, an irreversible hydrolysis process begins leading to the formation of two water-soluble products. For the experiments we use a peristaltic pump and a high precision injection pump to control the injection rate of the organic liquid and tracer.</p><p>A Darcy-scale numerical model is used to simulate the immiscible displacement process coupled with the reactive tracer transport across the fluid-fluid interface. The results show that the current reactive transport model is not always capable to reproduce the breakthrough curves of tracer experiments and that a new theoretical framework may be required.</p><p>Investigations of the role of solid surface area of the grains show that the grain surface roughness has an important influence on the IFA. . Furthermore, a linear relationship between the mobile capillary associated IFA and the inverse mean grain diameter can be established. The results are compared with the data collected from literature measured with high resolution microtomography and partitioning tracer methods. The capillary associated IFA values are consistently smaller because KIS tracers measure the mobile part of the interface. Through this study the applicability range of the KIS tracers is considerably expanded and the confidence in the robustness of the method is improved.</p><p> </p><p> </p><p>Schaffer M, Maier F, Licha T, Sauter M (2013) A new generation of tracers for the characterization of interfacial areas during supercritical carbon dioxide injections into deep saline aquifers: Kinetic interface-sensitive tracers (KIS tracer). International Journal of Greenhouse Gas Control 14:200–208. https://doi.org/10.1016/j.ijggc.2013.01.020</p><p>Tatomir A, Vriendt KD, Zhou D, et al (2018) Kinetic Interface Sensitive Tracers: Experimental Validation in a Two-Phase Flow Column Experiment. A Proof of Concept. Water Resources Research 54:10,223-10,241. https://doi.org/10.1029/2018WR022621</p>

scholarly journals Sodium Tanshinone IIA Sulfonate Prevents Angiotensin II-Induced Differentiation of Human Atrial Fibroblasts into Myofibroblasts

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Tangting Chen ◽  
Miaoling Li ◽  
Xuehui Fan ◽  
Jun Cheng ◽  
Liqun Wang
Keyword(s):  
Angiotensin Ii ◽  
Critical Role ◽  
Water Soluble ◽  
Collagen I ◽  
Tanshinone Iia ◽  
Ang Ii ◽  
Induced Differentiation ◽  
Fibroblast Migration ◽  
Collagen Iii ◽  
Sodium Tanshinone Iia Sulfonate

Differentiation of atrial fibroblasts into myofibroblasts plays a critical role in atrial fibrosis. Sodium tanshinone IIA sulfonate (DS-201), a water-soluble derivative of tanshinone IIA, has been shown to have potent antifibrotic properties. However, the protective effects of DS-201 on angiotensin II- (Ang II-) induced differentiation of atrial fibroblasts into myofibroblasts remain to be elucidated. In this study, human atrial fibroblasts were stimulated with Ang II in the presence or absence of DS-201. Then, α-smooth muscle actin (α-SMA), collagen I, and collagen III expression and reactive oxygen species (ROS) generation were measured. The expression of transforming growth factor-β1 (TGF-β1) and the downstream signaling of TGF-β1, such as phosphorylation of Smad2/3, were also determined. The results demonstrated that DS-201 significantly prevented Ang II-induced human atrial fibroblast migration and decreased Ang II-induced α-SMA, collagen I, and collagen III expression. Furthermore, increased production of ROS and expression of TGF-β1 stimulated by Ang II were also significantly inhibited by DS-201. Consistent with these results, DS-201 significantly inhibited Ang II-evoked Smad2/3 phosphorylation and periostin expression. These results and the experiments involving N-acetyl cysteine (antioxidant) and an anti-TGF-β1 antibody suggest that DS-201 prevent Ang II-induced differentiation of atrial fibroblasts to myofibroblasts, at least in part, through suppressing oxidative stress and inhibiting the activation of TGF-β1 signaling pathway. All of these data indicate the potential utility of DS-201 for the treatment of cardiac fibrosis.

scholarly journals Effective stress regime around a jacked steel pile during installation ageing and load testing in chalk

2018 ◽  
Vol 55 (11) ◽  
pp. 1577-1591 ◽  
Author(s):  
R.M. Buckley ◽  
R.J. Jardine ◽  
S. Kontoe ◽  
B.M. Lehane
Keyword(s):  
Cyclic Loading ◽  
Effective Stress ◽  
Test Site ◽  
Static Tension ◽  
Load Testing ◽  
Stress Regime ◽  
Effective Stresses ◽  
Axial Cyclic Loading ◽  
Tension Testing ◽  
Static And Cyclic Loading

This paper reports experiments with 102 mm diameter closed-ended instrumented Imperial College piles (ICPs) jacked into low- to medium-density chalk at a well-characterized UK test site. The “ICP” instruments allowed the effective stress regime surrounding the pile shaft to be tracked during pile installation, equalization periods of up to 2.5 months, and load testing under static tension and one-way axial cyclic loading. Installation resistances are shown to be dominated by the pile tip loads. Low installation shaft stresses and radial effective stresses were measured that correlated with local cone penetration test (CPT) tip resistances. Marked shaft total stress reductions and steep stress gradients are demonstrated in the vicinity of the pile tip. The local interface shaft effective stress paths developed during static and cyclic loading displayed trends that resemble those seen in comparable tests in sands. Shaft failure followed the Coulomb law and constrained interface dilation was apparent as the pile experienced drained loading to failure, although with a lesser degree of radial expansion than with sands. Radial effective stresses were also found to fall with time after installation, leading to reductions in shaft capacity as proven by subsequent static tension testing. The jacked, closed-ended, piles’ ageing trends contrast sharply with those found with open piles driven at the same site, indicating that ageing is affected by pile tip geometry and (or) installation method.

scholarly journals Non-toxic low-cost heavy liquid separation in the Geological Survey of Greenland

1989 ◽  
Vol 145 ◽  
pp. 11-13
Author(s):  
P Schiøler
Keyword(s):  
Health Risk ◽  
Low Cost ◽  
Water Soluble ◽  
Heavy Liquid ◽  
Organic Liquids ◽  
Federal Republic Of Germany ◽  
Water Soluble Compound ◽  
Efficient Alternative ◽  
Sodium Polytungstate ◽  
Heavy Liquids

Density separation of mineral and sediment grains into fractions using heavy liquids traditionally employs organic compounds such as bromoform (density 2.89) and tetrabromoethane (density 2.96) which are known to be toxic even at very low concentrations (Van Haaften, 1969) and possibly carcinogenic. In addition, the separated grains are washed with organic solvents such as acetone which may be highly inflammable, and are also a health risk. In recent years, a new water soluble compound, sodium polytungstate (SPT), 3Na2WO4.9WO3.H2O, has become available as a medium for heavy liquid separations, offering an alternative to the heavy organic liquids. Hs use has been discussed by several workers (e.g. Plewinsky & Kamp, 1984; Krukowski, 1988) in a variety of geological settings. The present note summarises experience in GGU's palaeontological laboratory gained from working with SPT for a full year as a replacement for tetrabromoethane and bromoform in the separation of phosphatic microfossils from samples principally of Lower - Middle Cambrian age. Apart from improving the work environment by replacing high health-risk chernicals with water soluble products without known detrimental effects, SPT has proved to be both an economical and potentially efficient alternative to the organic heavy liquids. SPT is patented, and only available from Sometu, Falkenried 4, D 1000 Berlin 33, Federal Republic of Germany.

Sign in / Sign up

Export Citation Format

Share Document