An analysis of three-dimensional ground movements: the Thunder Bay tunnel

1991 ◽  
Vol 28 (1) ◽  
pp. 25-41 ◽  
Author(s):  
K. M. Lee ◽  
R. K. Rowe
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Triaxial Tests ◽  
Soil Parameters ◽  
Tunnel Face ◽  
Element Analysis ◽  
Soft Clays ◽  
Ground Deformations ◽  
Thunder Bay ◽  
Stress Dependent

A three-dimensional (3D) elastoplastic finite-element analysis, which is capable of simulating the advance of a tunnelling shield and the associated ground losses resulting from the tunnelling process, is used to calculate the deformations caused by the excavation of the Thunder Bay sewer tunnel. The soil parameters adopted in the analysis were based on the results determined from stress-dependent triaxial tests. The results of this analysis are compared with the measured soil displacements. Reasonable agreement between the calculated and observed 3D settlement distribution and horizontal displacements at different distances from the tunnel face is reported. This overall agreement for displacements under 3D conditions suggests that the method of analysis may be applicable to design problems involving tunnelling in soft clays similar to that at the Thunder Bay sewer tunnel provided that the soil parameters are reliably determined. Key words: tunnelling, three-dimensional analysis, finite element, elastoplastic displacements, ground deformations, Thunder Bay tunnel.

scholarly journals STUDY ON NONLINEAR PAVEMENT RESPONSES OF LOW VOLUME ROADWAYS SUBJECT TO MULTIPLE WHEEL LOADS / NETIESINĖS KELIO DANGOS PRIKLAUSOMYBĖS NUO MAŽO INTENSYVUMO KELIŲ, VEIKIAMŲ DAUGKARTINĖMIS RATŲ APKROVOMIS, TYRIMAS

2011 ◽  
Vol 17 (1) ◽  
pp. 45-54 ◽  
Author(s):  
Minkwan Kim ◽  
Joo Hyoung Lee
Keyword(s):  
Finite Element ◽  
Numerical Study ◽  
Asphalt Pavement ◽  
Three Dimensional ◽  
Nonlinear Behavior ◽  
Element Model ◽  
Element Analysis ◽  
Nonlinear Stress ◽  
Low Volume ◽  
Stress Dependent

This paper describes numerical analyses on low volume roads (LVRs) using a nonlinear three-dimensional (3D) finite element model (FEM). Various pavement scenarios are analyzed to investigate the effects of pavement layer thicknesses, traffic loads, and material properties on pavement responses, such as surface deflection and subgrade strain. Each scenario incorporates a different combination of wheel/axle configurations and pavement geomaterial properties to analyze the nonlinear behavior of thinly surfaced asphalt pavement. In this numerical study, nonlinear stress-dependent models are employed in the base and subgrade layers to properly characterize pavement geomaterial behavior. Finite element analysis results are then described in terms of the effects of the asphalt pavement thickness, wheel/axle configurations, and geomaterial properties on critical pavement responses. Conclusions are drawn by the comparison of the nonlinear pavement responses in the base and subgrade in association with the effects of multiple wheel/axle load interactions. Santrauka Straipsnyje aprašoma skaitinė mažo intensyvumo kelių analizė, taikant netiesinį—erdvinį baigtinių elementų modelį. Skirtingi dangų paviršiaus variantai analizuojami siekiant ištirti, kokiąįtaką kelio dangos elgsenai, t. y. poslinkiams ir kelio pagrindo deformacijoms, turi dangų sluoksnių storiai, eismo apkrovos ir medžiagų savybės. Kiekvienas kelio dangos variantas turi skirtingas ratų arba ašies ir geometrinių savybių formas, kad būtų galima išanalizuoti netiesinę plonos asfalto dangos paviršiaus elgseną. Šioje skaitinėje analizėje nagrinėjami netiesiniai įtempių modeliai, kurie buvo taikomi pagrindo sluoksniams, siekiant tinkamai apibūdinti geometrinę kelio dangos elgseną. Baigtinių elementų analizės rezultatai toliau nagrinėjami atsižvelgiant į asfalto dangos storį ar ašies formą ir geometrines savybes, priklausomai nuo kritinės kelio dangos būklės. Išvados buvo gautos lyginant netiesines kelių dangos priklausomybes pagrindo sluoksnyje, atsižvelgiant į jų sąveiką su daugkartine ratų apkrova.

Finite Element Analysis of El Infiernillo Dam

1973 ◽  
Vol 10 (2) ◽  
pp. 129-144 ◽  
Author(s):  
N. A. Skermer
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Soil Structure ◽  
Triaxial Tests ◽  
Soil Parameters ◽  
Element Analysis ◽  
The Core ◽  
Rockfill Dam ◽  
The Finite Element Analysis ◽  
Fundamental Understanding

A simple trapezoidal element is presented for use in the analysis of thin core rockfill dams with nonlinear soil parameters. Handling of nonlinear soil parameters and allowance for the intermediate principal stress in plane strain problems are discussed. The analysis of El Infiernillo rockfill dam using trapezoids in the core and transitions, and variable Young's modulus and Poisson's ratio, reveals the transfer of stress that takes place around the core. Comparisons of strain observations at El Infiernillo Dam with results from the analysis are good, except in zones of compacted rockfill. It appears that the actual stiffness of compacted granular fills may be seriously underestimated, if soil parameters are based on data obtained from triaxial tests on normally consolidated samples. A fundamental understanding of soil deformation behavior would lead to an improvement in the finite element analysis of soil structure.

Method for Getting the Soil Elastic Modulus in the Finite Element Analysis of the Deep Foundation Excavation in Tianjin

2012 ◽  
Vol 170-173 ◽  
pp. 386-389
Author(s):  
Shi Lun Feng ◽  
Pu Lin Li ◽  
Jun Li ◽  
Yuming Zhou
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Elastic Modulus ◽  
Three Dimensional ◽  
Soil Parameters ◽  
Deep Foundation ◽  
Foundation Pit ◽  
Element Analysis ◽  
Finite Element Software ◽  
Deep Foundation Excavation

The finite element method has been used widely in foundation pit engineering to simulate the deep foundation excavation, but it is troublesome and time-consuming to get the important calculation parameter of the soil elastic modulus. So a method based on the comon soil parameters is proposed to get the soil elastic modulus. And a real foundation excavation was simulated using the finite element software ABAQUS and the soil elastic modulus got according to the proposed method. The three-dimensional finite element analysis results were compared to the field data, and both results were close to each other.

Effects of occlusal scheme on All-on-Four abutments, screws and prostheses: A three-dimensional finite element study

2020 ◽  
Author(s):  
Nurullah Türker ◽  
Hümeyra Tercanlı Alkış ◽  
Steven J Sadowsky ◽  
Ulviye Şebnem Büyükkaplan
Keyword(s):  
Finite Element ◽  
Three Dimensional ◽  
Good Prognosis ◽  
Von Mises Stress ◽  
Element Analysis ◽  
Group Function ◽  
Occlusal Contact ◽  
Maximum Deformation ◽  
Contact Points ◽  
Von Mises

An ideal occlusal scheme plays an important role in a good prognosis of All-on-Four applications, as it does for other implant therapies, due to the potential impact of occlusal loads on implant prosthetic components. The aim of the present three-dimensional (3D) finite element analysis (FEA) study was to investigate the stresses on abutments, screws and prostheses that are generated by occlusal loads via different occlusal schemes in the All-on-Four concept. Three-dimensional models of the maxilla, mandible, implants, implant substructures and prostheses were designed according to the All-on-Four concept. Forces were applied from the occlusal contact points formed in maximum intercuspation and eccentric movements in canine guidance occlusion (CGO), group function occlusion (GFO) and lingualized occlusion (LO). The von Mises stress values for abutment and screws and deformation values for prostheses were obtained and results were evaluated comparatively. It was observed that the stresses on screws and abutments were more evenly distributed in GFO. Maximum deformation values for prosthesis were observed in the CFO model for lateral movement both in the maxilla and mandible. Within the limits of the present study, GFO may be suggested to reduce stresses on screws, abutments and prostheses in the All-on-Four concept.

Towards Predicting Relative Belt Edge Endurance With the Finite Element Method

1990 ◽  
Vol 18 (4) ◽  
pp. 216-235 ◽  
Author(s):  
J. De Eskinazi ◽  
K. Ishihara ◽  
H. Volk ◽  
T. C. Warholic
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Three Dimensional ◽  
The Finite Element Method ◽  
Shear Deformations ◽  
Element Analysis ◽  
Vertical Loading ◽  
Predicted Values ◽  
Element Method

Abstract The paper describes the intention of the authors to determine whether it is possible to predict relative belt edge endurance for radial passenger car tires using the finite element method. Three groups of tires with different belt edge configurations were tested on a fleet test in an attempt to validate predictions from the finite element results. A two-dimensional, axisymmetric finite element analysis was first used to determine if the results from such an analysis, with emphasis on the shear deformations between the belts, could be used to predict a relative ranking for belt edge endurance. It is shown that such an analysis can lead to erroneous conclusions. A three-dimensional analysis in which tires are modeled under free rotation and static vertical loading was performed next. This approach resulted in an improvement in the quality of the correlations. The differences in the predicted values of various stress analysis parameters for the three belt edge configurations are studied and their implication on predicting belt edge endurance is discussed.

Torsional Analysis of a Steel Cord-Rubber Tire Belt Structure

1996 ◽  
Vol 24 (4) ◽  
pp. 339-348 ◽  
Author(s):  
R. M. V. Pidaparti
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Composite Structures ◽  
Three Dimensional ◽  
Element Model ◽  
Torsional Stiffness ◽  
Element Analysis ◽  
Rubber Belt ◽  
Steel Cord ◽  
Torsional Analysis

Abstract A three-dimensional (3D) beam finite element model was developed to investigate the torsional stiffness of a twisted steel-reinforced cord-rubber belt structure. The present 3D beam element takes into account the coupled extension, bending, and twisting deformations characteristic of the complex behavior of cord-rubber composite structures. The extension-twisting coupling due to the twisted nature of the cords was also considered in the finite element model. The results of torsional stiffness obtained from the finite element analysis for twisted cords and the two-ply steel cord-rubber belt structure are compared to the experimental data and other alternate solutions available in the literature. The effects of cord orientation, anisotropy, and rubber core surrounding the twisted cords on the torsional stiffness properties are presented and discussed.

Finite Element Modeling for Steel Cord Analysis in Radial Tires

2013 ◽  
Vol 41 (1) ◽  
pp. 60-79 ◽  
Author(s):  
Wei Yintao ◽  
Luo Yiwen ◽  
Miao Yiming ◽  
Chai Delong ◽  
Feng Xijin
Keyword(s):  
Finite Element ◽  
High Efficiency ◽  
Force Measurement ◽  
Three Dimensional ◽  
Local Stress ◽  
Tension Force ◽  
Center Line ◽  
Element Analysis ◽  
Design Variables ◽  
Steel Cord

ABSTRACT: This article focuses on steel cord deformation and force investigation within heavy-duty radial tires. Typical bending deformation and tension force distributions of steel reinforcement within a truck bus radial (TBR) tire have been obtained, and they provide useful input for the local scale modeling of the steel cord. The three-dimensional carpet plots of the cord force distribution within a TBR tire are presented. The carcass-bending curvature is derived from the deformation of the carcass center line. A high-efficiency modeling approach for layered multistrand cord structures has been developed that uses cord design variables such as lay angle, lay length, and radius of the strand center line as input. Several types of steel cord have been modeled using the developed method as an example. The pure tension for two cords and the combined tension bending under various loading conditions relevant to tire deformation have been simulated by a finite element analysis (FEA). Good agreement has been found between experimental and FEA-determined tension force-displacement curves, and the characteristic structural and plastic deformation phases have been revealed by the FE simulation. Furthermore, some interesting local stress and deformation patterns under combined tension and bending are found that have not been previously reported. In addition, an experimental cord force measurement approach is included in this article.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

Sign in / Sign up

Export Citation Format

Share Document