Stability threshold for cyclic loading of saturated clay

1989 ◽  
Vol 26 (1) ◽  
pp. 122-131 ◽  
Author(s):  
Guy Lefebvre ◽  
Denis LeBoeuf ◽  
Benoît Demers
Keyword(s):  
Shear Strength ◽  
Cyclic Loading ◽  
Strain Rate ◽  
Undrained Shear Strength ◽  
Triaxial Tests ◽  
Repeated Loading ◽  
Loading Test ◽  
Stability Threshold ◽  
The Stability ◽  
Undrained Shear

This paper presents the results of an experimental investigation performed to study the stability threshold under cyclic (repeated) loading, and the postcyclic static strength of a sensitive clay from the Hudson Bay region. The strain rate and structure effects were also studied by carrying out monotonic and cyclic triaxial tests at both slow and rapid strain rates or frequencies, and at confining pressures above and below the apparent preconsolidation pressure. The stability threshold for both structured and normally consolidated Grande Baleine clay is about 60–65% of the original undrained shear strength measured at the same strain rate as that used in the repeated loading test. The undrained shear strength and the failure envelope remain essentially unchanged if the repeated preloading is kept below the threshold. The clay structure remains unaltered by this preloading. Key words: clay, stability threshold, cyclic loading, earthquake, postcyclic strength.

scholarly journals Effects of compaction on soil undrained shear strength deteriorating during undrained cyclic loading and controlling seismic stability of embankment

2019 ◽  
Vol 92 ◽  
pp. 18003 ◽  
Author(s):  
Antoine Duttine ◽  
Fumio Tatsuoka ◽  
Kazuhiro Ueno
Keyword(s):  
Shear Strength ◽  
Cyclic Loading ◽  
Seismic Analysis ◽  
Undrained Shear Strength ◽  
Seismic Stability ◽  
Triaxial Tests ◽  
Response Analysis ◽  
Total Stress ◽  
Earth Fill ◽  
Undrained Shear

Effects of compaction on the undrained shear strength of saturated earth-fill dam materials are presented. Poorly and well compacted saturated soils may exhibit undrained shear strengths, respectively, significantly lower and higher than corresponding drained shear strength and this trend is amplified as the undrained strength deteriorates by preceding undrained cyclic loading. These features are implemented in a new simplified seismic analysis to evaluate residual deformation of earth-fill dams. The analysis consists of: 1) a modified Newmark sliding block analysis; and 2) a pseudo-static non-linear FEM analysis, both formulated in a unified framework based on the cumulative damage concept, total stress earthquake response analysis and a direct total stress modelling of undrained monotonic and cyclic stress-strain behaviours obtained by triaxial tests. The analysis simulates very well the collapse of an earth-fill dam by the 2011 Off the Pacific Coast of Tohoku Earthquake, Japan, and indicates a substantially higher seismic stability under the same conditions of the newly restored dam completed in 2017. Paramount effects of soil compaction on the seismic stability of earth-filled dam are demonstrated.

A Characteristic and a Precisely Constitutive Model for Undrained Clay

2020 ◽  
Vol 975 ◽  
pp. 203-207
Author(s):  
Shih Tsung Hsu ◽  
Wen Chi Hu ◽  
Yu Heng Lin ◽  
Zhuo Ling
Keyword(s):  
Shear Strength ◽  
Plastic Strain ◽  
Constitutive Model ◽  
Strain Hardening ◽  
Undrained Shear Strength ◽  
Triaxial Tests ◽  
Stress Strain ◽  
Proposed Model ◽  
Taipei Basin ◽  
Undrained Shear

Constitutive models for soils are usually adopted in numerical method to analyze the behavior of geotechnical structures. This study performs a series of consolidated-undrained triaxial tests to establish the stress-strain curve of clay. A constitutive model that considers continuous strain hardening-softening is proposed based on the results of triaxial tests. Triaxial test results reveal that undrained shear strength linearly increases with an increase in consolidated pressure , the normalized undrained shear strength is about 0.52 not only for this study but also for the other two cases around Taipei Basin. Due to undrained condition, an associated flow rule between plastic strain increment and stress tensor is adopted. As accumulative plastic strain or/and consolidated pressure change, the mobilized undrained shear strength also changes. All parameters needed for the proposed model can be expressed as a function of undrained shear strength Su, The mobilized undrained shear strength for the proposed model during strain hardening-softening can be in term of accumulative plastic strain. This model can calculate the stress-strain curves of clayed soils accurately.

Triaxial tests on model sand columns in clay

2004 ◽  
Vol 41 (2) ◽  
pp. 299-312 ◽  
Author(s):  
V Sivakumar ◽  
D McKelvey ◽  
J Graham ◽  
D Hughes
Keyword(s):  
Shear Strength ◽  
Undrained Shear Strength ◽  
Stone Columns ◽  
Triaxial Tests ◽  
Column Length ◽  
Uniform Loading ◽  
Moist Sand ◽  
Triaxial Cell ◽  
Foundation Type ◽  
Undrained Shear

Vibro-stone columns can improve the bearing capacity and reduce the settlement of foundations. Their performance depends on the strength of the column material, reinforcement method of column installation, type of in situ soil, area replacement ratio, and column length. This paper examines the behaviour of small laboratory specimens of soft clay (undrained shear strength ≈ 30 kPa) reinforced with sand columns when tested under known boundary stress conditions. Two series of tests were carried out on kaolin specimens (diameter 100 mm, height 200 mm) in a triaxial cell. In the first series, specimens were reinforced with a 32 mm diameter column of sand, 80, 120, 160, or 200 mm long. Columns were installed by (i) compacting moist sand into a prebored hole or (ii) freezing a column of moist sand before inserting it into a prebored hole. In the second series, columns were reinforced with geo-grids before installation. The specimens were subjected to (i) uniform loading in which the load was applied over the entire surface area of the specimen or (ii) foundation-type loading in which only a small area in the centre of the specimen was loaded. Under uniform loading, the specimens containing a full-depth column were significantly stronger than specimens without columns. Specimens with single, partially penetrating columns installed by wet compaction were weaker than specimens without columns. When frozen columns were installed, strengths increased progressively. Under foundation-type loading, bearing capacities increased with an increase in column length. Geo-grid reinforcement produced significant increases in load-carrying capacity.Key words: ground improvement, undrained shear strength, consolidation, stress path.

scholarly journals Simple Method for Prediction of Undrained Shear Strength of Saturated Soil Subjected to Cyclic Loading

2020 ◽  
Vol 15 (2) ◽  
pp. 241-256
Author(s):  
Kazuhiro UENO ◽  
Akira IZUMI ◽  
Antoine DUTTINE ◽  
Sumio YAZAKI ◽  
Toshikazu HORI
Keyword(s):  
Shear Strength ◽  
Cyclic Loading ◽  
Undrained Shear Strength ◽  
Saturated Soil ◽  
Simple Method ◽  
Undrained Shear

scholarly journals UNDRAINED SHEAR STRENGTH PARAMETERS OF SAPROCK FROM A WEATHERING PROFILE OVER PORPHYRITIC BIOTITE GRANITE AT KM 31 OF THE KUALA LUMPUR - KARAK HIGHWAY, PENINSULAR MALAYSIA

2021 ◽  
Vol 33 (2) ◽  
Author(s):  
John Kuna Raj
Keyword(s):  
Shear Strength ◽  
Friction Angle ◽  
Undrained Shear Strength ◽  
Triaxial Tests ◽  
Regression Analyses ◽  
Shear Strength Parameters ◽  
Weathering Profile ◽  
Strength Parameters ◽  
Zone Ii ◽  
Undrained Shear

Three broad zones can be differentiated at the weathering profile; an upper, 9.4 m thick, pedological soil (zone I), an intermediate, 31.7 m thick, saprock (zone II) and the bottom bedrock (zone III). The saprock (zone II) comprises gravelly silty sands that distinctly preserve the minerals, textures and structures of the original granite and can be separated into sub-zones II A, II B, II C, and II D, based on differences in preservation of relict structures and content of litho-relicts (core-boulders). To characterize the undrained strength of saprock, samples were collected from sub-zones II A, II B, II C and II D and their physical and soil index properties determined before unconsolidated undrained triaxial tests were carried out on remolded samples. Three to four individual samples from each sub-zone were compressed under confining pressures of 138 kPa, 207 kPa, 276 kPa and/or 345 kPa. Plots of pf = [(σ1 + σ3)/2] versus qf = [(σ1 - σ3)/2] were then used to calculate apparent cohesions of 41.9 kPa, 100.3 kPa, 76.1 kPa and 73.9 kPa, and friction angles of 32.2o, 28.1o, 26.6o and 27.8o, for the samples from sub-zones II A, II B, II C, and II D, respectively. Regression analyses show apparent cohesions to decrease with increasing clay contents, and degrees of saturation; features indicating the influence of negative pore water (or suction) pressures. Regression analyses also show apparent friction angle to increase with increasing sand contents; a feature attributed to greater inter-locking and resistance to displacement of these particles. It is concluded that the undrained shear strength parameters of saprock are characterized by an average apparent cohesion of 54.6 kPa, and friction angle of 30.5o; the parameters influenced by the degree of saturation as well as clay and sand contents.

UNDRAINED SHEAR STRENGTH OF K0 CONSOLIDATED SOFT CLAYS UNDER TRIAXIAL AND PLANE STRAIN CONDITIONS

2014 ◽  
Vol 06 (03) ◽  
pp. 1450032 ◽  
Author(s):  
QIUSHENG WANG ◽  
XIULI DU ◽  
QIUMING GONG
Keyword(s):  
Shear Strength ◽  
Plane Strain ◽  
Yield Surface ◽  
Critical State ◽  
Volumetric Strain ◽  
Stress Path ◽  
Undrained Shear Strength ◽  
Triaxial Tests ◽  
Soft Clays ◽  
Undrained Shear

Theoretical formulas for predicting the undrained shear strength of K0 consolidated soft clays under the stress path related to triaxial and plane strain tests are presented within the framework of critical state soil mechanics. An inclined elliptical yield surface is adopted to take account of the initial anisotropic stress state. The undrained strength is determined by combining the undrained stress path in the volumetric stress–strain space and the initial yield surface in the deviator-mean stress space. The derived mathematical expressions are functions of the critical state frictional angle, the plastic volumetric strain ratio and the overconsolidation ratio, which can be simplified into the solutions for isotropically consolidated clays under triaxial tests or under plane strain tests. The results calculated by using the theoretical formulas obtained in this paper are in good agreement with the available collected test results. It indicates that these new formulas are applicable to triaxial and plane strain tests on normally and lightly to moderately overconsolidated soft clays.

scholarly journals Critical undrained shear strength of sand-silt mixtures under monotonic loading

2015 ◽  
Vol 18 (2) ◽  
pp. 149-156 ◽  
Author(s):  
Mohamed Bensoula ◽  
Hanifi Missoum ◽  
Karim Bendani
Keyword(s):  
Shear Strength ◽  
Void Ratio ◽  
Undrained Shear Strength ◽  
Monotonic Loading ◽  
Triaxial Tests ◽  
Empirical Relationships ◽  
Fine Content ◽  
Fines Content ◽  
Chain Force ◽  
Undrained Shear

<p>This study uses experimental triaxial tests with monotonic loading to develop empirical relationships to estimate undrained critical shear strength. The effect of the fines content on undrained shear strength is analyzed for different density states. The parametric analysis indicates that, based on the soil void ratio and fine content properties, the undrained critical shear strength first increases and then decreases as the proportion of fines increases, which demonstrates the influence of fine content on a soil’s vulnerability to liquefaction. A series of monotonic undrained triaxial tests were performed on reconstituted saturated sand-silt mixtures. Beyond 30% fines content, a fraction of the silt participates in the soil’s skeleton chain force. In this context, the concept of the equivalent intergranular void ratio may be an appropriate parameter to express the critical shear strength of the studied soil. This parameter is able to control the undrained shear strength of non-plastic silt and sand mixtures with different densities.</p><p> </p><p><strong>Resumen</strong></p><p>Este estudio utiliza evaluaciones experimentales triaxiales con cargas repetitivas para desarrollar relaciones empíricas y estimar la tensión crítica de corte bajo condiciones no drenadas. El efecto de contenido de finos en la tensión de corte sin drenar se analizó en diferentes estados de densidad. El análisis paramétrico indica que, basado en la porosidad del suelo y las propiedades del material de finos, la tensión de corte sin drenar primero se incrementa y luego decrece mientras la proporción de finos aumenta, lo que demuestra la influencia de contenido de finos en la vulnerabilidad del suelo a la licuación. Una serie de las evaluaciones se realizó en  mezclas rehidratadas y saturadas de arena y cieno. Más allá del 30 % de los contenidos finos, una fracción del cieno hace parte principal de la cadena de fuerza del suelo. En este contexto, el concepto de porosidad equivalente intergranular puede ser un parámetro apropiado para expresar la tensión crítica de corte del suelo estudiado. Este parámetro nos permite controlar la tensión de corte sin drenar de cieno no plástico y mezclas de arena de densidades diferentes.</p>

Finite element modeling of partially embedded pipelines in clay seabed using Coupled Eulerian–Lagrangian method

2015 ◽  
Vol 52 (1) ◽  
pp. 58-72 ◽  
Author(s):  
Sujan Dutta ◽  
Bipul Hawlader ◽  
Ryan Phillips
Keyword(s):  
Finite Element ◽  
Shear Strength ◽  
Strain Rate ◽  
Deep Water ◽  
Strain Softening ◽  
Mesh Size ◽  
Undrained Shear Strength ◽  
Band Formation ◽  
Offshore Pipelines ◽  
Undrained Shear

Vertical seabed penetration and lateral movement of deep-water offshore pipelines are simulated using the Coupled Eulerian–Lagrangian (CEL) approach in Abaqus finite element (FE) software. Abaqus CEL has been used in some previous studies to simulate large-deformation behavior of offshore pipelines; however, the effects of strain rate and strain-softening on undrained shear strength (su) have not been considered. In this study, the effects of these factors are critically examined. The available built-in models in Abaqus CEL cannot account for these factors directly, especially the strain rate; therefore, the development of user subroutines is required. In the present study, a simple but realistic soil constitutive model (published by Zhou and Randolph in 2007) that considers the effects of strain rate and strain-softening on su is implemented in Abaqus CEL. The effects of FE mesh size and shear band formation on penetration resistance are discussed based on a comprehensive FE simulation. Lateral analyses are performed for “light” and “heavy” pipes in clay seabed having a linearly increasing undrained shear strength profile for smooth and rough pipe–soil interface conditions. The FE results are compared with previous theoretical, numerical, and centrifuge test results. Based on the present FE analyses, it is shown that, similar to the remeshing and interpolation techniques with small strain (RITSS) technique developed at the The University of Western Australia, the Abaqus CEL can successfully simulate the response of partially embedded pipelines in deep-water clay seabed, provided strain rate and softening dependent clay models are implemented. A methodology to implement such a model using Abaqus user subroutine is also presented.

Sign in / Sign up

Export Citation Format

Share Document