Preconsolidation pressures in intertill glaciolacustrine clay near Blaine Lake, Saskatchewan

1988 ◽  
Vol 25 (4) ◽  
pp. 831-839 ◽  
Author(s):  
E. Karl Sauer ◽  
E. A. Christiansen
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Ice Thickness ◽  
Excess Pore Water Pressure ◽  
Stability Of Slopes ◽  
Preconsolidation Pressure ◽  
Insufficient Time ◽  
Degree Of Consolidation ◽  
Excess Pore

Soft, intertill, glaciolacustrine clays are of concern for stability of slopes and foundations. An intertill clay deposit between 32 and 54 m below the surface was continuously cored. Index properties were determined for 46 samples and 10 samples were tested on the oedometer. Stratigraphic evidence indicates that the glaciolacustrine clay (Blaine Lake Member), lying between the till of the Sutherland and Saskatoon groups, was glaciated three times. However, preconsolidation pressures of this intertill clay show the degree of consolidation is less than 20% based on a total stress from an estimated ice thickness extrapolated from the Cypress Hills. This low preconsolidation pressure suggests there was insufficient time for dissipation of excess pore-water pressure created by thickening of the advancing glacier. Key words: preconsolidation pressure, excess pore-water pressure, glaciers, intertill clay.

scholarly journals EVALUASI SETTLEMENT MENGGUNAKAN SURCHARGE PRELOADING DENGAN PVD PADA PROYEK DI BANDUNG SELATAN

2020 ◽  
Vol 3 (3) ◽  
pp. 911
Author(s):  
Michael Christopher Yapriadi ◽  
Inda Sumarli ◽  
Ali Iskandar
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soil Improvement ◽  
Soil Layers ◽  
Excess Pore Water Pressure ◽  
Surcharge Preloading ◽  
Improvement Method ◽  
Degree Of Consolidation ◽  
Excess Pore

The development in Indonesia continues to grow. Hence, the feasible land for construction is drastically decreased. However, some projects must be constructed on that kind of land. One solution to solve this problem is by using a soil improvement. A project in Bandung Selatan chose to apply Surcharge Preloading with PVD soil improvement method. This project used a combination of 9,2 metres surcharge preload and a 28 metres depth PVD, with triangular formation and 1,2 metres spacing. The soil improvement was finished after 548 days. This analysis aims to evaluate the settlement from the soil improvement result, which is 1,297 metres. This analysis uses a finite difference method program. The excess pore water pressure from the analysis result is 0,229 T/m2 on the 548th day. Therefore, these soil layers have possibilities to settle again in future. The 90% degree of consolidation settlement for this soil layers is 2,31 metres, which will be reached on the 813,4th days. It is suspected that there are some mistakes either during the soil improvement designing or the soil improvement process. Pembangunan di Indonesia terus berkembang. Akibatnya jumlah tanah yang baik untuk proyek konstruksi semakin menipis. Kendati demikian, ada kalanya suatu proyek harus dilaksanakan di lokasi tersebut. Salah satu solusi yang dapat ditempuh adalah dengan melakukan perbaikan tanah. Sebuah proyek di Bandung Selatan melakukan perbaikan tanah dengan metode Surcharge Preloading dengan PVD. Proyek ini menggunakan kombinasi antara timbunan setinggi 9,2 meter dan PVD sedalam 28 meter, dengan formasi segitiga yang dipasang dengan jarak antar PVD 1,2 meter. Perbaikan tanah dilakukan selama 548 hari. Analisis ini bertujuan melakukan evaluasi terhadap kurang maksimalnya penurunan di lapangan yang hanya mencapai 1,297 meter. Analisis dilakukan dengan bantuan program beda hingga. Berdasarkan hasil analisis, besarnya excess pore water pressure pada hari ke-548 adalah 0,229 T/m,2, sehingga lapisan tanah tersebut masih memiliki potensi untuk mengalami penurunan. Adapun penurunan konsolidasi 90% yang dapat terjadi sebesar 2,31 meter pada hari ke-813,4. Diduga terdapat kesalahan baik dalam perhitungan perencanaan awal ataupun saat pelaksanaan di lapangan.

scholarly journals Analysis of Large-Strain Consolidation Behavior of Soil with High Water Content in Consideration of Self-Weight

2018 ◽  
Vol 2018 ◽  
pp. 1-10 ◽  
Author(s):  
Yupeng Cao ◽  
Jian Yang ◽  
Guizhong Xu ◽  
Jianwen Xu
Keyword(s):  
Pore Water ◽  
Void Ratio ◽  
Pore Water Pressure ◽  
Large Strain ◽  
Water Pressure ◽  
Average Degree ◽  
High Water Content ◽  
Excess Pore Water Pressure ◽  
Degree Of Consolidation ◽  
Excess Pore

Based on the axisymmetric large-strain consolidation (ALSC) model with the void ratio as the variable under equal strain condition, difference schemes of model’s equation, initial condition, and boundary condition were given. Taking phosphatic clay in Florida as a research object, the consolidation behaviors of soil with high water content by axisymmetric large-strain theory and one-dimensional large-strain theory were analyzed. The effect of different kinds of consolidation theories and self-weight stress on an average degree of consolidation was evaluated. The development of the void ratio and excess pore water pressure along the soil layer was clarified. The results show that the theoretical value of Terzaghi’s consolidation degree is always less than that of ALSC (Us, the average degree of consolidation defined by strain)-vertical drainage in the consolidation process. Terzaghi’s solution overestimates the dissipation rate of excess pore water pressure during the earlier consolidation period but underestimates it during the later consolidation period. The degree of consolidation calculated by Hansbo develops faster than ALSC (Up, the average degree of consolidation defined by stress)-radial drainage, but slower than ALSC (Us)-radial drainage. In the ALSC model, Us is always been faster than Up. The effect of self-weight on the consolidation degree of axisymmetric large-strain consolidation theory is relatively small (maximum error is less than 16%), while it can accelerate the consolidation rate of soil in one-dimensional large-strain consolidation theory largely. When only the vertical drainage occurs, the consolidation rate in the middle of the soil is obviously lagging the upper and lower parts, while the radial drainage can reduce the void ratio and the excess pore water pressure along the soil layer uniformly and more rapidly.

Stress–strain pattern–based criterion to assess cyclic shear resistance of soil from laboratory element tests

2016 ◽  
Vol 53 (9) ◽  
pp. 1460-1473 ◽  
Author(s):  
Dharma Wijewickreme ◽  
Achala Soysa
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Shear Stiffness ◽  
Large Strains ◽  
Fundamental Parameter ◽  
Stress Strain ◽  
Cyclic Shear ◽  
Excess Pore Water Pressure ◽  
Excess Pore

The cyclic shear response of soils is commonly examined using undrained (or constant-volume) laboratory element tests conducted using triaxial and direct simple shear (DSS) devices. The cyclic resistance ratio (CRR) from these tests is expressed in terms of the number of cycles of loading to reach unacceptable performance that is defined in terms of the attainment of a certain excess pore-water pressure and (or) strain level. While strain accumulation is generally commensurate with excess pore-water pressure, the definition of unacceptable performance in laboratory tests based purely on cyclic strain criteria is not robust. The shear stiffness is a more fundamental parameter in describing engineering performance than the excess pore-water pressure alone or shear strain alone; so far, no criterion has considered shear stiffness to determine CRR. Data from cyclic DSS tests indicate consistent differences inherent in the patterns between the stress–strain loops at initial and later stages of cyclic loading; instead of relatively “smooth” stress–strain loops in the initial parts of loading, nonsmooth changes in incremental stiffness showing “kinks” are notable in the stress–strain loops at large strains. The point of pattern change in a stress–strain loop provides a meaningful basis to determine the CRR (based on unacceptable performance) in cyclic shear tests.

Consolidation Theory for Composite Ground with Granular Columns Based on Different Calculation Models

2011 ◽  
Vol 261-263 ◽  
pp. 1534-1538
Author(s):  
Yu Guo Zhang ◽  
Ya Dong Bian ◽  
Kang He Xie
Keyword(s):  
Pore Water ◽  
Analytical Solutions ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Vertical Flow ◽  
Excess Pore Water Pressure ◽  
Consolidation Theory ◽  
Composite Ground ◽  
Granular Column ◽  
Excess Pore

The consolidation of the composite ground under non-uniformly distributed initial excess pore water pressure along depth was studied in two models which respectively considering both the radial and vertical flows in granular column and the vertical flow only in granular column, and the corresponding analytical solutions of the two models were presented and compared with each other. It shows that the distribution of initial excess pore water pressure has obvious influence on the consolidation of the composite ground with single drainage boundary, and the rate of consolidation considering the radial-vertical flow in granular column is faster than that considering the vertical flow only in granular column.

The Test Study to the Changes of Excess Pore Water Pressure during Precast Pile Construction

2012 ◽  
Vol 193-194 ◽  
pp. 1010-1013
Author(s):  
Shu Qing Zhao
Keyword(s):  
Pore Water ◽  
Clayey Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Excess Pore Pressure ◽  
Soil Pressure ◽  
Excess Pore Water Pressure ◽  
Test Study ◽  
Excess Pore

The construct to precast pile in thick clayey soil can cause the accumulation of excess pore water pressure. The high excess pore pressure can make soil, buildings and pipes surrounded have large deflection, even make them injured. Combining with actual projects, this paper presents an in-situ model test on the changes of excess pore water pressure caused by precast pile construct. It is found that the radius of influence range for single pile driven is about 15m，the excess pore water pressure can reach or even exceed the above effective soil pressure, and there are two relatively stable stages.

A Practical Saturated Sand Elastic-Plastic Dynamic Constitutive Model and Application

2012 ◽  
Vol 446-449 ◽  
pp. 1621-1626 ◽  
Author(s):  
Yan Mei Zhang ◽  
Dong Hua Ruan
Keyword(s):  
Constitutive Model ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Stone Columns ◽  
Saturated Sand ◽  
Multidimensional Model ◽  
Excess Pore Water Pressure ◽  
Elastic Plastic ◽  
Excess Pore

A practical saturated sand elastic-plastic dynamic constitutive model was developed on the base of Handin-Drnevich class nonlinear lag model and multidimensional model. In this model, during the calculation of loading before soil reaches yielding, unloading and inverse loading, corrected Handin-Drnevich equivalent nonlinear model was adopted; after soil yielding, based on the idea of multidimensional model, the composite hardening law which combines isotropy hardening and follow-up hardening, corrected Mohr-Coulomb yielding criterion and correlation flow principle were adopted. A fully coupled three dimension effective stress dynamic analysis procedure was developed on the base of this model. The seismic response of liquefaction foundation reinforced by stone columns was analyzed by the developed procedure. The research shows that with the diameter of stone columns increasing, the excess pore water pressure in soil between piles decreases; with the spacing of columns increasing, the excess pore water pressure increases. The influence of both is major in middle and lower level of composite foundation.

scholarly journals Effect of Reduced Zone on Time-Dependent Analysis of Tunnels

2011 ◽  
Vol 2011 ◽  
pp. 1-12
Author(s):  
Mohammed Y. Fattah ◽  
Kais T. Shlash ◽  
Nahla M. Salim
Keyword(s):  
Finite Element ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Outer Diameter ◽  
Transient Effects ◽  
Excess Pore Water Pressure ◽  
Modified Cam Clay ◽  
Tunnel Diameter ◽  
Excess Pore

The problem of the proposed “Baghdad metro line” which consists of two routes of 32 km long and 36 stations is analyzed. The tunnel is circular in cross-section with a 5.9 m outer diameter. The finite element analyses were carried out using elastic-plastic and modified Cam clay models for the soil. The excavation has been used together with transient effects through a fully coupled Biot formulation. All these models and the excavation technique together with Biot consolidation are implemented into finite-element computer program named “Modf-CRISP” developed for the purpose of these analyses. The results indicate that there is an inward movement at the crown and this movement is restricted to four and half tunnel diameters. A limited movement can be noticed at spring line which reaches 0.05% of tunnel diameter, while there is a heave at the region below the invert, which reaches its maximum value of about 0.14% of the diameter and is also restricted to a region extending to 1.5 diameters. The effect of using reduced zone on excess pore water pressure and surface settlement (vertical and horizontal) was also considered and it was found that the excess pore water pressure increases while the settlement trough becomes deeper and narrower using reduced .

Security Control Method of Loading for Surcharge Preloading Based on the Stress Path

2011 ◽  
Vol 368-373 ◽  
pp. 2795-2803
Author(s):  
Heng Hu ◽  
Yan Li ◽  
Zhi Liang Dong ◽  
Yan Luo ◽  
Gong Xin Zhang
Keyword(s):  
Pore Water ◽  
Safety Factor ◽  
Control Method ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Stress Path ◽  
Excess Pore Water Pressure ◽  
Surcharge Preloading ◽  
Security Control ◽  
Excess Pore

All the time, security control method of loading is an important research part in the surcharge preloading, which is directly related to safety of the construction process. Starting from the stress path, discussing the variation of excess pore water pressure and relationship between stress path and security, and bringing forward the control method with a safety factor Fs based on the stress path. By measuring the change of excess pore water pressure, the control method with a safety factor Fs can reflect quantitatively the security status of soil and achieve the purpose of the process control, finally the security control method including the safety factor of loading and speed control is put forward to monitor construction safety. The safety factor of loading Fs is verified and back analyzed with the finite-element software, getting the correction factor from 0.90 to 1.20.

Sign in / Sign up

Export Citation Format

Share Document