Analysis of progressive deformation of the Edmonton Convention Centre excavation

1987 ◽  
Vol 24 (3) ◽  
pp. 430-440 ◽  
Author(s):  
D. H. Chan ◽  
N. R. Morgenstern
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Strain Softening ◽  
Progressive Failure ◽  
Field Measurements ◽  
Shear Zones ◽  
Element Model ◽  
Progressive Deformation ◽  
Element Analysis ◽  
The Stability

A finite element analysis was performed of the deformations observed during the excavation of the Edmonton Convention Centre. Local geology in the Edmonton area consists of layers of shale with weak bentonite seams overlain by glacial deposits. The presence of the bentonite seams, which possess strain-softening characteristics, controls the stability of the excavation, which is located in a valley wall. To simulate the influence of the bentonite seams a strain-softening finite element model is used to estimate the amount of deformation in the foundation of the excavation. Field measurements indicated that localized progressive straining had occurred during the excavation process, and substantial heave of the foundation floor was observed. The finite element results show progressive deformation of the excavation and propagation of shear zones. Good agreement between the finite element results and the field observations is obtained. Key words: progressive failure, strain softening, finite element analysis, shear band, excavation stability.

FINITE ELEMENT ANALYSIS OF A DENTAL IMPLANT

2003 ◽  
Vol 15 (02) ◽  
pp. 82-85 ◽  
Author(s):  
SHYH-CHOUR HUANG ◽  
CHANG-FENG TSAI
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Stress Distribution ◽  
Element Model ◽  
Element Analysis ◽  
3 Dimensional ◽  
Dimensional Finite Element ◽  
The Stability ◽  
Stress Concentration Effect ◽  
Implant System

This paper presents results from using a 3-dimensional finite element model to assess the stress distribution in the bone, in the implant and in the abutment as a function of the implant's diameter and length. Increasing implant diameter and length increases the stability of the implant system. By using a finite element analysis, we show that implant length does not decrease the stress distribution of either the implant or the bone. Alternatively, however implant diameter increases reduce the stresses. For the latter case, the contact area between implant and bone is increased thus the stress concentration effect is decreased. Also, with increased implant diameter the bone loss is decreased and as a consequence the success rate is improved.

scholarly journals Factor of Safety Reduction Factors for Accounting for Progressive Failure for Earthen Levees with Underlying Thin Layers of Sensitive Soils

2013 ◽  
Vol 2013 ◽  
pp. 1-13 ◽  
Author(s):  
Adam J. Lobbestael ◽  
Adda Athanasopoulos-Zekkos ◽  
Josh Colley
Keyword(s):  
Finite Element ◽  
Strain Softening ◽  
Progressive Failure ◽  
Limit Equilibrium ◽  
Thin Layers ◽  
The Finite Element Method ◽  
Element Analysis ◽  
Limit Equilibrium Methods ◽  
The Stability ◽  
Reduction Factors

The effects of progressive failure on flood embankments with underlying thin layers of soft, sensitive soils are investigated. Finite element analysis allows for investigation of strain-softening effects and progressive failure in soft and sensitive soils. However, limit equilibrium methods for slope stability analysis, widely used in industry, cannot capture these effects and may result in unconservative factors of safety. A parametric analysis was conducted to investigate the effect of thin layers of soft sensitive soils on the stability of flood embankments. A flood embankment was modeled using both the limit equilibrium method and the finite element method. The foundation profile was altered to determine the extent to which varying soft and sensitive soils affected the stability of the embankment, with respect to progressive failure. The results from the two methods were compared to determine reduction factors that can be applied towards factors of safety computed using limit equilibrium methods, in order to capture progressive failure.

Structural Finite Element Analysis on Side Wall Pouring Formwork Trolley for Subway Station

2013 ◽  
Vol 380-384 ◽  
pp. 95-100
Author(s):  
Yan Fang Ma ◽  
Zhen Tong He ◽  
Qin Zhao
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Light Condition ◽  
Side Wall ◽  
Element Model ◽  
Structure Design ◽  
Analysis Software ◽  
Element Analysis ◽  
Work Condition ◽  
The Stability

Structure finite element analysis software ANSYS is used to establish relatively complete finite element model for automatic side wall formwork trolley, analyze the stability of formwork trolley under light condition and work condition, and give a correct classification on working conditions of formwork trolley. Main factors influencing the stability of formwork trolley are found and improving measures are proposed to provide reference for optimal structure design and standardized design of formwork trolley.

Study on Influence of Implant Thickness and Fixation Position on Implant Stability Using Finite Element Analysis

2011 ◽  
Vol 9 ◽  
pp. 47-55
Author(s):  
D. Devika ◽  
G. Arumaikkannu
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Bone Fractures ◽  
Element Model ◽  
Lateral Position ◽  
Implant Design ◽  
Orthopaedic Implant ◽  
Element Analysis ◽  
The Stability ◽  
As Stress

Patient anatomy specific orthopaedic implant design, fabrication and identification of the most suitable position to fix implants onto bone fractures are challenging problems for surgeons to overcome of the existing shortcomings of commercially available implants. In this work, a 3D finite element model of the left tibial bone of an adult male is developed from Computed Tomography scan images. Proximal tibial fracture type B1 (as per Association for the Study of Internal Fixation) is simulated on the bone model. A geometry specific implant is obtained in order to promote better bone ingrowths and uniform stress distribution, by extracting the surface features of the bone. Finite Element Analysis is performed to evaluate and compare the mechanical properties such as stress, strain and displacement of the bone and implant of four various thicknesses which are fixed at two different positions. The design objectives such as low stress and displacement combination is obtained through the antero-lateral position with 1.8 mm implant thickness. Various material properties are assigned to cortical, cancellous, trabecular regions of the bone and to implants made up of titanium alloy. The results obtained from the Finite Element Analysis are used to evaluate the stability and suitability of the implant for that particular fracture.

Finite Element Analysis of Nonuniformity of Tires with Imperfections5

2007 ◽  
Vol 35 (3) ◽  
pp. 226-238 ◽  
Author(s):  
K. M. Jeong ◽  
K. W. Kim ◽  
H. G. Beom ◽  
J. U. Park
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Radial Force ◽  
Element Analysis ◽  
The Finite Element Analysis ◽  
Dimensional Finite Element ◽  
Force Variation ◽  
Three Dimensional Finite Element

Abstract The effects of variations in stiffness and geometry on the nonuniformity of tires are investigated by using the finite element analysis. In order to evaluate tire uniformity, a three-dimensional finite element model of the tire with imperfections is developed. This paper considers how imperfections, such as variations in stiffness or geometry and run-out, contribute to detrimental effects on tire nonuniformity. It is found that the radial force variation of a tire with imperfections depends strongly on the geometrical variations of the tire.

scholarly journals Comparison of Tooth- and Bone-Borne Appliances on the Stress Distributions and Displacement Patterns in the Facial Skeleton in Surgically Assisted Rapid Maxillary Expansion—A Finite Element Analysis (FEA) Study

Materials ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1152
Author(s):  
Rafał Nowak ◽  
Anna Olejnik ◽  
Hanna Gerber ◽  
Roman Frątczak ◽  
Ewa Zawiślak
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Three Dimensional ◽  
Element Model ◽  
Rapid Maxillary Expansion ◽  
Stress Distributions ◽  
Maxillary Expansion ◽  
Facial Skeleton ◽  
Element Analysis ◽  
Maxillary Constriction

The aim of this study was to compare the reduced stresses according to Huber’s hypothesis and the displacement pattern in the region of the facial skeleton using a tooth- or bone-borne appliance in surgically assisted rapid maxillary expansion (SARME). In the current literature, the lack of updated reports about biomechanical effects in bone-borne appliances used in SARME is noticeable. Finite element analysis (FEA) was used for this study. Six facial skeleton models were created, five with various variants of osteotomy and one without osteotomy. Two different appliances for maxillary expansion were used for each model. The three-dimensional (3D) model of the facial skeleton was created on the basis of spiral computed tomography (CT) scans of a 32-year-old patient with maxillary constriction. The finite element model was built using ANSYS 15.0 software, in which the computations were carried out. Stress distributions and displacement values along the 3D axes were found for each osteotomy variant with the expansion of the tooth- and the bone-borne devices at a level of 0.5 mm. The investigation showed that in the case of a full osteotomy of the maxilla, as described by Bell and Epker in 1976, the method of fixing the appliance for maxillary expansion had no impact on the distribution of the reduced stresses according to Huber’s hypothesis in the facial skeleton. In the case of the bone-borne appliance, the load on the teeth, which may lead to periodontal and orthodontic complications, was eliminated. In the case of a full osteotomy of the maxilla, displacements in the buccolingual direction for all the variables of the bone-borne appliance were slightly bigger than for the tooth-borne appliance.

Finite Element Analysis and Optimization of Long-Span Gantry NC Machining Center Structure

2011 ◽  
Vol 346 ◽  
pp. 379-384
Author(s):  
Shu Bo Xu ◽  
Yang Xi ◽  
Cai Nian Jing ◽  
Ke Ke Sun
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Design Method ◽  
Dynamic Performance ◽  
Plate Thickness ◽  
Element Model ◽  
Wall Structure ◽  
Characteristic Analysis ◽  
Element Analysis ◽  
Dynamic Performance Analysis

The use of finite element theory and modal analysis theory, the structure of the machine static and dynamic performance analysis and prediction using optimal design method for optimization, the new machine to improve job performance, improve processing accuracy, shorten the development cycle and enhance the competitiveness of products is very important. Selected for three-dimensional CAD modeling software-UG NX4.0 and finite element analysis software-ANSYS to set up the structure of the beam finite element model, and then post on the overall structure of the static and dynamic characteristic analysis, on the basis of optimized static and dynamic performance is more superior double wall structure of the beam. And by changing the wall thickness and the thickness of the inner wall, as well as the reinforcement plate thickness overall sensitivity analysis shows that changes in these three parameters on the dynamic characteristics of post impact. Application of topology optimization methods, determine the optimal structure of the beam ultimately.

Sign in / Sign up

Export Citation Format

Share Document