THE EFFECTIVE STRESS RESPONSE OF A SATURATED CLAY SOIL TO REPEATED LOADING

1969 ◽  
Vol 6 (3) ◽  
pp. 241-252 ◽  
Author(s):  
D. A. Sangrey ◽  
D. J. Henkel ◽  
M. I. Esrig
Keyword(s):  
Pore Water ◽  
Effective Stress ◽  
Critical Level ◽  
Clay Soil ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Triaxial Tests ◽  
Repeated Loading ◽  
Repeated Stress ◽  
Saturated Clay

The results of a series of tests designed to examine the behavior of saturated clay soil under repeated loading are reported. Triaxial tests, under conditions of axial symmetry, were used and the rates of deformation were chosen so as to permit the accurate measurement of pore water pressure at all stages of the tests.It was found that, for any particular consolidation history, a critical level of repeated stress existed. Below this critical level, a state of nonfailure equilibrium was reached in which the stress-strain curves followed closed hysteresis loops. Above the critical level of repeated stress, effective stress failure occurred; and each cycle of loading produced cumulative increases in deformation.An interesting feature of the test results was that a linear relationship between the magnitude of the applied repeated stress and the increase in pore water pressure was found for stress levels below the critical value.

scholarly journals Implications of the principle of effective stress

2020 ◽  
Author(s):  
Gerd Gudehus
Keyword(s):  
Critical Phenomena ◽  
Pore Water ◽  
Effective Stress ◽  
Critical Points ◽  
Pore Water Pressure ◽  
Numerical Models ◽  
Water Pressure ◽  
Shear Bands ◽  
Triaxial Tests ◽  
Water Saturated

AbstractWhile Terzaghi justified his principle of effective stress for water-saturated soil empirically, it can be derived by means of the neutrality of the mineral with respect to changes of the pore water pressure $$p_w$$ p w . This principle works also with dilating shear bands arising beyond critical points of saturated grain fabrics, and with patterns of shear bands as relics of critical phenomena. The shear strength of over-consolidated clay is explained without effective cohesion, which results also from swelling up to decay, while rapid shearing of water-saturated clay can lead to a cavitation of pore water. The $$p_w$$ p w -neutrality is also confirmed by triaxial tests with sandstone samples, while Biot’s relation with a reduction factor for $$p_w$$ p w is contestable. An effective stress tensor is heuristically legitimate also for soil and rock with relics of critical phenomena, particularly for critical points with a Mohr–Coulomb condition. Therein, the $$p_w$$ p w -neutrality of the solid mineral determines the interaction of solid fabric and pore water, but numerical models are questionable due to fractal features.

scholarly journals Soil liquefaction as an identification test

2019 ◽  
Vol 92 ◽  
pp. 08008
Author(s):  
Bozana Bacic ◽  
Ivo Herle
Keyword(s):  
Pore Water ◽  
Laboratory Testing ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Initial Density ◽  
Soil Liquefaction ◽  
Triaxial Tests ◽  
Cyclic Triaxial ◽  
Cyclic Triaxial Tests ◽  
Identification Test

Time-consuming and complicated investigations of soil liquefaction in cyclic triaxial tests are the most common way of laboratory analysis of this phenomenon. Moreover, the necessary equipment for the performance of cyclic triaxial tests is very expensive. Much simpler method for laboratory testing of the soil liquefaction has been developed at the Institute of Geotechnical Engineering at the TU Dresden. This method takes into account the pore water pressure build-up during cyclic shearing within a short time period. During the test, the soil sample is subjected to horizontal cyclic loading and the generated pore water pressure is measured. In the first series of these experiments, a dependence of the pore water pressure buildup on the initial density of soil could be observed, as expected. When comparing different soils, it is shown that the tendency to liquefaction depends also on the granulometric properties (e.g. grain size distribution) of the soil. The aim of the further development is to establish a simple identification test for laboratory testing of the soil liquefaction.

Effective stress paths and yielding in soft clays below embankments

1985 ◽  
Vol 22 (3) ◽  
pp. 357-374 ◽  
Author(s):  
D. J. Folkes ◽  
J. H. A. Crooks
Keyword(s):  
Pore Water ◽  
Effective Stress ◽  
Strain Softening ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Clay ◽  
Stress Path ◽  
Excess Pore Water Pressure ◽  
Soft Clays ◽  
Effective Stress Path

Current methods of predicting the response of soft clays to surface loading are often unsuccessful because the assumed constitutive relationships, including effective stress path behaviour, are incorrect. In particular, the transition from small-strain to large-strain behaviour (i.e. yielding) is frequently not taken into account. Recent laboratory testing has demonstrated that the behaviour of soft clays is largely controlled by yielding. The locus of effective stress states causing yield is known as the yield envelope (YE).The effective stress paths (ESP's) in soft clay foundations below the centre of six fills were determined from computed total stresses and measured pore-water pressures. Yield behaviour is clearly indicated by ESP shapes. The yield envelopes inferred from analyses of field data are similar to those obtained from laboratory testing. Effective stress path shapes vary widely, depending on a variety of factors, including imposed stress level, rate of construction, and boundary drainage conditions. This finding contradicts an earlier conclusion that soft clay behaviour can be characterized by a single ESP. Because of the wide range of possible ESP shapes, the parameters [Formula: see text] does not provide an adequate basis for determining the effective stress state in a soft clay.The ESP/YE analyses indicate that yield can occur either during loading or during excess pore-water pressure dissipation following completion of loading. Yield of sensitive soils during loading is usually followed by strain softening. However, in some soils, dilatant behaviour appears to occur. Yield during dissipation of excess pore-water pressure is characterized by a dramatic change in cv and increased compressibility. Key words: soft clay, yield, effective stress paths, field behaviour, strain softening, rate of consolidation.

Earthquake-induced deformation analyses of the Upper San Fernando Dam under the 1971 San Fernando Earthquake

2001 ◽  
Vol 38 (1) ◽  
pp. 1-15 ◽  
Author(s):  
Guoxi Wu
Keyword(s):  
Finite Element ◽  
Pore Water ◽  
Effective Stress ◽  
Pore Water Pressure ◽  
Ground Deformation ◽  
Water Pressure ◽  
Soil Liquefaction ◽  
Shear Stresses ◽  
Cyclic Shear ◽  
San Fernando

A nonlinear effective stress finite element approach for dynamic analysis of soil structure is described in the paper. Major features of this approach include the use of a third parameter in the two-parameter hyperbolic stress-strain model, a modified expression for unloading–reloading modulus in the Martin–Finn–Seed pore-water pressure model, and an additional pore-water pressure model based on cyclic shear stress. The additional pore-water pressure model uses the equivalent number of uniform cyclic shear stresses for the assessment of pore-water pressure. Dynamic analyses were then conducted to simulate the seismically induced soil liquefaction and ground deformation of the Upper San Fernando Dam under the 1971 San Fernando Earthquake. The analyses were conducted using the finite element computer program VERSAT. The computed zones of liquefaction and deformation are compared with the measured response and with results obtained by others.Key words: effective stress method, finite element analysis, Upper San Fernando Dam, earthquake deformation, VERSAT.

EXPERIMENT STUDY ON DYNAMIC STRENGTH OF LOESS UNDER REPEATED LOAD

2008 ◽  
Vol 22 (31n32) ◽  
pp. 5825-5830 ◽  
Author(s):  
ZHENGHUA XIAO ◽  
BO HAN ◽  
HONGJIAN LIAO ◽  
AKENJIANG TUOHUTI
Keyword(s):  
Shear Strength ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Axial Strain ◽  
Water Pressure ◽  
Dynamic Strength ◽  
Triaxial Tests ◽  
Dynamic Shear ◽  
Anisotropic Consolidation ◽  
Dynamic Shear Strength

A series of dynamic triaxial tests are performed on normal anisotropic consolidation and over anisotropic consolidation specimens of loess. Based on the test results, the variable regularity of dynamic shear stress, axial strain and pore water pressure of loess under dynamic loading are measured and analyzed. The influences of the dynamic shear strength and pore water pressure at different over consolidation ratio are analyzed. The relationship between dynamic shear strength and over consolidation ratio of loess is obtained. The evaluating standard of dynamic shear strength of loess is discussed. Meanwhile, how to determine the effective dynamic shear strength index of normal anisotropic consolidated loess is also discussed in this paper. Several obtained conclusions can be referenced for studying the dynamic shear strength of loess foundation.

scholarly journals Swelling phenomena and effective stress in compacted expansive clays

2016 ◽  
Vol 53 (1) ◽  
pp. 134-147 ◽  
Author(s):  
David Mašín ◽  
Nasser Khalili
Keyword(s):  
Pore Water ◽  
Effective Stress ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Swelling Pressure ◽  
Constitutive Modelling ◽  
Dry Density ◽  
Expansive Clay ◽  
Experimental Database ◽  
Clay Aggregates

The central aim of this paper is to discuss the applicability of the effective stress principle as defined by Terzaghi (total stress minus pore-water pressure) to predict the behaviour of expansive clay aggregates. Phenomena occurring between individual clay minerals are reviewed first at the molecular level obtained in the colloid science research. In particular, it is noted that, for interparticle distances higher than approximately 1.5 nm, the pore-water pressure in the bulk equilibrium solution forms an additive component of the interparticle disjoining pressure. It is concluded that for these distances Terzaghi’s effective stress principle should be adequate to describe the clay behaviour. To support these developments, an extensive experimental database of nine different sodium and calcium bentonites available in the published literature was analysed. With the aid of double structure constitutive modelling, procedures were developed to extract information about the behaviour of clay aggregates from the experimental measurements. It was then shown that unconfined water retention curves, swelling pressure tests, swelling under constant load tests, and mechanical unloading tests are all uniquely related in terms of the dependency of dry density (or void ratio) of clay aggregate versus mean effective stress. By considering reversibility of aggregate behaviour and full saturation of aggregates, this implies that the effective stress principle is a valid way of predicting expansive clay aggregate volumetric deformation.

scholarly journals Evaluation of local friction and pore-water pressure evolution along instrumented probes in saturated clay for large numbers of cycles

2019 ◽  
Vol 56 (12) ◽  
pp. 1953-1967
Author(s):  
Rawaz Dlawar Muhammed ◽  
Jean Canou ◽  
Jean-Claude Dupla ◽  
Alain Tabbagh
Keyword(s):  
Cyclic Loading ◽  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Static Friction ◽  
Good Picture ◽  
Friction Resistance ◽  
Saturated Clay ◽  
Tip Resistance ◽  
Number Of Cycles

To investigate local friction mobilization along piles subjected to cyclic axial loadings, a calibration chamber experiment is presented based on the implementation of instrumented probes in specimens of saturated clay. Typical results obtained with a piezo-probe are presented, allowing not only tip resistance and local friction to be measured, but also the local pore-water pressure developed on the probe shaft. In addition, specific piezometers installed in the clay specimen allow a good picture to be obtained of the pore-water pressure field around the probe during installation and loading. After installation of the probe, a succession of monotonic and cyclic displacement-controlled loading phases is applied. Upon displacement-controlled cyclic loading of the piezo-probe up to a very large number of cycles (105 cycles), an initial degradation of local friction is observed followed by a subsequent reinforcement, which continues until the end of the cyclic sequence. The friction evolution is related to the evolution of the pore-water pressure measured during cyclic loading. In particular, the influence of the cyclic loading sequence on the post-cyclic static friction resistance is evaluated. A comparison is finally made with the results obtained with another type of probe, showing a good consistency between both types of results.

Sign in / Sign up

Export Citation Format

Share Document