Numerical modeling of liquefaction and comparison with centrifuge tests

2004 ◽  
Vol 41 (2) ◽  
pp. 193-211 ◽  
Author(s):  
Peter M Byrne ◽  
Sung-Sik Park ◽  
Michael Beaty ◽  
Michael Sharp ◽  
Lenart Gonzalez ◽  
...  
Keyword(s):  
Numerical Modeling ◽  
Effective Stress ◽  
Centrifuge Modeling ◽  
Confining Stress ◽  
Centrifuge Model ◽  
Centrifuge Tests ◽  
High Acceleration ◽  
Complete Saturation ◽  
Earth Structures ◽  
High Seismicity

The prediction of liquefaction and resulting displacements is a major concern for earth structures located in regions of moderate to high seismicity. Conventional procedures used to assess liquefaction commonly predict the triggering of liquefaction to depths of 50 m or more. Remediation to prevent or curtail liquefaction at these depths can be very expensive. Field experience during past earthquakes indicates that liquefaction has mainly occurred at depths less than about 15 m, and some recent dynamic centrifuge model testing initially appeared to confirm a depth or confining-stress limitation on the occurrence of liquefaction. Such a limitation on liquefaction could greatly reduce remediation costs. In this paper an effective stress numerical modeling procedure is used to assess these centrifuge tests. The results indicate that a lack of complete saturation and densification at depth arising from the application of the high-acceleration field are largely responsible for the apparent limitation on liquefaction at depth observed in some centrifuge tests.Key words: liquefaction, dynamic centrifuge modeling, numerical modeling, depth limitation.

Evaluation of Dynamic Behavior of Pile Foundations for Interim Storage Facilities Through Geotechnical Centrifuge Tests

2002 ◽  
Author(s):  
Shizuo Tsurumaki ◽  
Hiroyuki Watanabe ◽  
Akira Tateishi ◽  
Kenichi Horikoshi ◽  
Shunichi Suzuki
Keyword(s):  
Dynamic Behavior ◽  
Experimental Studies ◽  
Centrifuge Modeling ◽  
Pile Foundations ◽  
Soil Conditions ◽  
Confining Stress ◽  
Geotechnical Centrifuge ◽  
Centrifuge Tests ◽  
Interim Storage ◽  
Storage Facilities

In Japan, there is a possibility that interim storage facilities for recycled nuclear fuel resources may be constructed on quaternary layers, rather than on hard rock. In such a case, the storage facilities need to be supported by pile foundations or spread foundations to meet the required safety level. The authors have conducted a series of experimental studies on the dynamic behavior of storage facilities supported by pile foundations. A centrifuge modeling technique was used to satisfy the required similitude between the reduced size model and the prototype. The centrifuge allows a high confining stress level equivalent to prototype deep soils to be generated (which is considered necessary for examining complex pile-soil interactions) as the soil strength and the deformation are highly dependent on the confining stress. The soil conditions were set at as experimental variables, and the results are compared. Since 2000, the Nuclear Power Engineering Corporation (NUPEC) has been conducting these research tests under the auspices on the Ministry of Economy, Trade and Industry of Japan.

Experimental Investigation of Depletion- and Injection-Induced Changes in Poromechanical, Transport, and Strength Properties of High-Porosity Sandstone

SPE Journal ◽  
2021 ◽  
pp. 1-21
Author(s):  
Saeed Rafieepour ◽  
Stefan Z. Miska ◽  
Evren M. Ozbayoglu ◽  
Nicholas E. Takach ◽  
Mengjiao Yu ◽  
...  
Keyword(s):  
Pore Pressure ◽  
Effective Stress ◽  
Microstructural Analysis ◽  
Optical Microscope ◽  
Strength Properties ◽  
Rock Properties ◽  
Absolute Permeability ◽  
High Porosity ◽  
Confining Stress ◽  
Stress Changes

Summary In this paper, an extensive series of experiments was performed to investigate the evolution of poromechanical (dry, drained, undrained, and unjacketed moduli), transport (permeability), and strength properties during reservoir depletion and injection in a high-porosity sandstone (Castlegate). An overdetermined set of eight poroelastic moduli was measured as a function of confining pressure (Pc) and pore pressure (Pp). The results showed larger effect on pore pressure at low Terzaghi’s effective stress (nonlinear trend) during depletion and injection. Moreover, the rock sample is stiffer during injection than depletion. At the same Pc and Pp, Biot’s coefficient and Skempton’s coefficient are larger in depletion than injection. Under deviatoric loading, absolute permeability decreased by 35% with increasing effective confining stress up to 20.68 MPa. Given these variations in rock properties, modeling of in-situ-stress changes using constant properties could attain erroneous predictions. Moreover, constant deviatoric stress-depletion/injection failure tests showed no changes or infinitesimal variations of strength properties with depletion and injection. It was found that failure of Castlegate sandstone is controlled by simple effective stress, as postulated by Terzaghi. Effective-stress coefficients at failure (effective-stress coefficient for strength) were found to be close to unity (actual numbers, however, were 1.03 for Samples CS-5 and CS-9 and 1.04 for Sample CS-10). Microstructural analysis of Castlegate sandstone using both scanning electron microscope (SEM) and optical microscope revealed that the changes in poroelastic and transport properties as well as the significant hysteresis between depletion and injection are attributed to the existence and distribution of compliant components such as pores, microcracks, and clay minerals.

The effect of pore pressure depletion and injection cycles on ultrasonic velocity and quality factor in a quartz sandstone

Geophysics ◽  
2007 ◽  
Vol 72 (2) ◽  
pp. E43-E51 ◽  
Author(s):  
P. Frempong ◽  
A. Donald ◽  
S. D. Butt
Keyword(s):  
Pore Pressure ◽  
Effective Stress ◽  
Axial Strain ◽  
Fluid Pressure ◽  
Porous Rocks ◽  
Confining Stress ◽  
Viscoelastic Deformation ◽  
Experimental Conditions ◽  
Pore Pressures ◽  
Pressure Depletion

Passing seismic waves generate transient pore-pressure changes that influence the velocity and attenuation characteristics of porous rocks. Compressional ultrasonic wave velocities [Formula: see text] and quality factors [Formula: see text] in a quartz sandstone were measured under cycled pore pressure and uniaxial strain conditions during a laboratory simulated injection and depletion process. The objectives were to study the influence of cyclical loading on the acoustic characteristics of a reservoir sandstone and to evaluate the potential to estimate pore-fluid pressure from acoustic measurements. The values of [Formula: see text] and [Formula: see text] were confirmed to increase with effective stress increase, but it was also observed that [Formula: see text] and [Formula: see text] increased with increasing pore pressure at constant effective stress. The effective stress coefficient [Formula: see text] was found to be less thanone and dependent on the pore pressure, confining stress, and load. At low pore pressures, [Formula: see text] approached one and reduced nonlinearly at high pore pressures. The change in [Formula: see text] and [Formula: see text] with respect to pore pressure was more pronounced at low versus high pore pressures. However, the [Formula: see text] variation with pore pressure followed a three-parameter exponential rise to a maximum limit whereas [Formula: see text] had no clear limit and followed a two-parameter exponential growth. Axial strain measurements during the pore-pressure depletion and injection cycles indicated progressive viscoelastic deformation in the rock. This resulted in an increased influence on [Formula: see text] and [Formula: see text] with increasing pore-pressure cycling. The value [Formula: see text] was more sensitive in responding to the loading cycle and changes in pore pressures than [Formula: see text]; thus, [Formula: see text] may be a better indicator for time-lapse reservoir monitoring than [Formula: see text]. However, under the experimental conditions, [Formula: see text] was unstable and difficult to measure at low effective stress.

scholarly journals Prefailure Deformation of Nailed Deep Excavations under Surcharge by Centrifuge Model Test

2021 ◽  
Vol 2021 ◽  
pp. 1-13
Author(s):  
S. Mohammad. Shoari Shoar ◽  
Ali A. Heshmati ◽  
Hossein Salehzadeh
Keyword(s):  
Model Test ◽  
Fracture Mechanism ◽  
Ground Surface ◽  
Centrifuge Model Test ◽  
Lateral Deformation ◽  
Ground Settlement ◽  
Deep Excavations ◽  
Centrifuge Model ◽  
Centrifuge Tests ◽  
The Moment

To study prefailure deformations in nailed deep vertical excavations under various surcharges, four centrifuge tests were used to explain the lateral deformation of facing, the fracture mechanism of cement facing, and the settlement profile of the ground surface. The soil used in this research was Firoozkooh sand No. 161. Both surcharge applying and excavation were performed at 40 g acceleration. The depth of the excavation was 30 cm, the length of the nail varied from H/3 to 2H/3 (H: excavation depth), and the nails were installed horizontally. The nails were made of brass pipes and then sand coated. The results showed that the effect of surcharge on the lateral deformation of the facing as well as the fracture mechanism of facing is obvious. Also, it was seen that the ground settlement profile is two-line or three-line at the moment of facing fracture and is affected by surcharge.

Sign in / Sign up

Export Citation Format

Share Document