Rapid calculation method for wave-guide-immersed dielectric resonant frequencies

2006 ◽  
Vol 84 (4) ◽  
pp. 289-297 ◽  
Author(s):  
Rudolf Nistor ◽  
Emil Petrescu
Keyword(s):  
Experimental Data ◽  
Calculation Method ◽  
Analysis Procedure ◽  
Wave Guide ◽  
Resonant Frequencies ◽  
Dielectric Sample ◽  
Margin Of Error ◽  
Rapid Calculation ◽  
Electrical Permittivity ◽  
Good Agreement

A rapid calculation is used to obtain the resonant frequencies of a dielectric sample excited in a semi-infinite wave guide. An analysis procedure for a sample excited in a semi-infinite wave guide is carried out to show the effect of the sample's dimensions and electrical permittivity. The theoretical resonant frequencies of the resonators are predicted and compared with those measured. The theoretical values of the resonant frequencies are in good agreement with experimental data within a margin of error less than 8%. PACS Nos.: 32.30.Bv, 41.20.Jb

The Arching Process Research of SRC Beam

2013 ◽  
Vol 482 ◽  
pp. 74-77
Author(s):  
Jun Liu ◽  
Hai Jun Yuan ◽  
Hua Li
Keyword(s):  
Experimental Data ◽  
Calculation Method ◽  
Design Method ◽  
Process Research ◽  
Vertical Shear ◽  
Shear Reinforcement ◽  
Beneficial Effects ◽  
Transfer Mode ◽  
Column Structure ◽  
Good Agreement

The purpose: The method to calculate slab-column middle connections under combined interaction of vertical shear and unbalanced moment is given to perfect the design method of slab-column structure; Method: The calculation method is proposed based on the calculation method of slab-column connection and the experimental data made by domestic and foreign scholars is used to verify. Result: The results verified by the formula are shown to be in good agreement with actual results. Conclusion: The interaction of shear and unbalanced moment are taken into account in the formula, including the transfer mode of unbalanced moment and the beneficial effects of shear reinforcement, to make the calculation more reasonable.

Energy Levels and Electromagnetic Transition of 90-94mo Nuclei Using Ibm-1

2020 ◽  
pp. 149-152
Keyword(s):  
Experimental Data ◽  
Transition Probability ◽  
Energy Levels ◽  
Dynamical Symmetry ◽  
Interacting Boson Model ◽  
Excitation Energies ◽  
Electromagnetic Transition ◽  
Boson Model ◽  
Energy States ◽  
Good Agreement

The energy states for the J , b , ɤ bands and electromagnetic transitions B (E2) values for even – even molybdenum 90 – 94 Mo nuclei are calculated in the present work of "the interacting boson model (IBM-1)" . The parameters of the equation of IBM-1 Hamiltonian are determined which yield the best excellent suit the experimental energy states . The positive parity of energy states are obtained by using IBS1. for program for even 90 – 94 Mo isotopes with bosons number 5 , 4 and 5 respectively. The" reduced transition probability B(E2)" of these neuclei are calculated and compared with the experimental data . The ratio of the excitation energies of the 41+ to 21+ states ( R4/2) are also calculated . The calculated and experimental (R4/2) values showed that the 90 – 94 Mo nuclei have the vibrational dynamical symmetry U(5). Good agreement was found from comparison between the calculated energy states and electric quadruple probabilities B(E2) transition of the 90–94Mo isotopes with the experimental data .

Tire Vibrations

1977 ◽  
Vol 5 (4) ◽  
pp. 202-225 ◽  
Author(s):  
G. R. Potts ◽  
C. A. Bell ◽  
L. T. Charek ◽  
T. K. Roy
Keyword(s):  
Natural Frequencies ◽  
Standing Waves ◽  
Resonant Mode ◽  
Mode Shapes ◽  
Resonant Vibrations ◽  
Resonant Frequencies ◽  
Radial Tire ◽  
Analysis Techniques ◽  
Thin Ring ◽  
Good Agreement

Abstract Natural frequencies and vibrating motions are determined in terms of the material and geometric properties of a radial tire modeled as a thin ring on an elastic foundation. Experimental checks of resonant frequencies show good agreement. Forced vibration solutions obtained are shown to consist of a superposition of resonant vibrations, each rotating around the tire at a rate depending on the mode number and the tire rotational speed. Theoretical rolling speeds that are upper bounds at which standing waves occur are determined and checked experimentally. Digital Fourier transform, transfer function, and modal analysis techniques used to determine the resonant mode shapes of a radial tire reveal that antiresonances are the primary transmitters of vibration to the tire axle.

Predicting the Effect of Tire Tread Pattern Design on Thick Film Wet Traction

1977 ◽  
Vol 5 (1) ◽  
pp. 6-28 ◽  
Author(s):  
A. L. Browne
Keyword(s):  
Experimental Data ◽  
Network Design ◽  
Thick Film ◽  
Digital Computer ◽  
Analytical Tool ◽  
Design Practice ◽  
Pattern Design ◽  
Performance Results ◽  
Good Agreement

Abstract An analytical tool is presented for the prediction of the effects of changes in tread pattern design on thick film wet traction performance. Results are reported for studies in which the analysis, implemented on a digital computer, was used to determine the effect of different tread geometry features, among these being the number, width, and lateral spacing of longitudinal grooves and the angle of zigzags in longitudinal grooves, on thick film wet traction. These results are shown to be in good agreement with experimental data appearing in the literature and are used to formulate guidelines for tread groove network design practice.

A New Condition of Formation and Stablity of All Crystalline Systems in a Good Agreement with Experimental Data

2015 ◽  
Vol 11 (3) ◽  
pp. 3224-3228
Author(s):  
Tarek El-Ashram
Keyword(s):  
Experimental Data ◽  
Brillouin Zone ◽  
Electron Concentration ◽  
Free Electron ◽  
Lattice Point ◽  
Valence Electron ◽  
Fermi Gas ◽  
Valence Electron Concentration ◽  
Fermi Sphere ◽  
Good Agreement

In this paper we derived a new condition of formation and stability of all crystalline systems and we checked its validity andit is found to be in a good agreement with experimental data. This condition is derived directly from the quantum conditionson the free electron Fermi gas inside the crystal. The new condition relates both the volume of Fermi sphere VF andvolume of Brillouin zone VB by the valence electron concentration VEC as ;𝑽𝑭𝑽𝑩= 𝒏𝑽𝑬𝑪𝟐for all crystalline systems (wheren is the number of atoms per lattice point).

Virus Removal by Filtration

1982 ◽  
Vol 14 (4-5) ◽  
pp. 253-256
Author(s):  
N Sriramula ◽  
M Chaudhuri
Keyword(s):  
Experimental Data ◽  
Escherichia Coli ◽  
Cationic Polyelectrolyte ◽  
Electrokinetic Phenomena ◽  
Virus Removal ◽  
Bacterial Virus ◽  
Gravity Settling ◽  
And Diffusion ◽  
Model Virus ◽  
Good Agreement

An investigation was undertaken on the removal of a model virus, bacterial virus MS2 against Escherichia coli, by sand filtration using untreated, and alum or cationic polyelectrolyte treated media, and uncoagulated as well as alum coagulated influent. Data on discrete virus removal were satisfactorily accounted for by electrokinetic phenomena and diffusion. For virus in association with turbidity, filter coefficients computed from experimental data were in good agreement with those predicted by mechanical straining and gravity settling which were the dominant mechanisms for removal of the turbidity particles to which the viruses attached.

Diffusion model for deposition of epitaxial GaAs layers prepared by the MOCVD method

1991 ◽  
Vol 56 (10) ◽  
pp. 2020-2029
Author(s):  
Jindřich Leitner ◽  
Petr Voňka ◽  
Josef Stejskal ◽  
Přemysl Klíma ◽  
Rudolf Hladina
Keyword(s):  
Experimental Data ◽  
Growth Rate ◽  
Kinetic Model ◽  
Gas Phase ◽  
Substrate Surface ◽  
Deposition Process ◽  
Hydrogen Atmosphere ◽  
Epitaxial Gaas ◽  
Kinetics Of ◽  
Good Agreement

The authors proposed and treated quantitatively a kinetic model for deposition of epitaxial GaAs layers prepared by reaction of trimethylgallium with arsine in hydrogen atmosphere. The transport of gallium to the surface of the substrate is considered as the controlling process. The influence of the rate of chemical reactions in the gas phase and on the substrate surface on the kinetics of the deposition process is neglected. The calculated dependence of the growth rate of the layers on the conditions of the deposition is in a good agreement with experimental data in the temperature range from 600 to 800°C.

Numerical evaluation of hydrodynamic characteristics of planing hulls by using a hybrid method

2021 ◽  
pp. 147509022199024
Author(s):  
Emre Kahramanoglu ◽  
Silvia Pennino ◽  
Huseyin Yilmaz
Keyword(s):  
Experimental Data ◽  
Hybrid Method ◽  
Design Stage ◽  
Hydrodynamic Characteristics ◽  
Calm Water ◽  
Preliminary Design Stage ◽  
Reduction Function ◽  
Hull Forms ◽  
Good Agreement

The hydrodynamic characteristics of the planing hulls in particular at the planing regime are completely different from the conventional hull forms and the determination of these characteristics is more complicated. In the present study, calm water hydrodynamic characteristics of planing hulls are investigated using a hybrid method. The hybrid method combines the dynamic trim and sinkage from the Zarnick approach with the Savitsky method in order to calculate the total resistance of the planing hull. Since the obtained dynamic trim and sinkage values by using the original Zarnick approach are not in good agreement with experimental data, an improvement is applied to the hybrid method using a reduction function proposed by Garme. The numerical results obtained by the hybrid and improved hybrid method are compared with each other and available experimental data. The results indicate that the improved hybrid method gives better results compared to the hybrid method, especially for the dynamic trim and resistance. Although the results have some discrepancies with experimental data in terms of resistance, trim and sinkage, the improved hybrid method becomes appealing particularly for the preliminary design stage of the planing hulls.

scholarly journals Fatigue Modeling and Numerical Analysis of Re-Filling Probe Hole of Friction Stir Spot Welded Joints in Aluminum Alloys

Materials ◽  
2021 ◽  
Vol 14 (9) ◽  
pp. 2171
Author(s):  
Armin Yousefi ◽  
Ahmad Serjouei ◽  
Reza Hedayati ◽  
Mahdi Bodaghi
Keyword(s):  
Experimental Data ◽  
Tensile Strength ◽  
Fatigue Life ◽  
Fatigue Strength ◽  
Fatigue Behavior ◽  
Element Model ◽  
Plastic Strain Amplitude ◽  
Friction Stir ◽  
Probe Hole ◽  
Good Agreement

In the present study, the fatigue behavior and tensile strength of A6061-T4 aluminum alloy, joined by friction stir spot welding (FSSW), are numerically investigated. The 3D finite element model (FEM) is used to analyze the FSSW joint by means of Abaqus software. The tensile strength is determined for FSSW joints with both a probe hole and a refilled probe hole. In order to calculate the fatigue life of FSSW joints, the hysteresis loop is first determined, and then the plastic strain amplitude is calculated. Finally, by using the Coffin-Manson equation, fatigue life is predicted. The results were verified against available experimental data from other literature, and a good agreement was observed between the FEM results and experimental data. The results showed that the joint’s tensile strength without a probe hole (refilled hole) is higher than the joint with a probe hole. Therefore, re-filling the probe hole is an effective method for structures jointed by FSSW subjected to a static load. The fatigue strength of the joint with a re-filled probe hole was nearly the same as the structure with a probe hole at low applied loads. Additionally, at a high applied load, the fatigue strength of joints with a refilled probe hole was slightly lower than the joint with a probe hole.

scholarly journals Validation of MATLAB algorithm to implement a two-step parallel pyrolysis model for the prediction of maximum %char yield

2021 ◽  
Vol 1 (1) ◽  
Author(s):  
Ibiba Taiwo Horsfall ◽  
Macmanus Chinenye Ndukwu ◽  
Fidelis Ibiang Abam ◽  
Ololade Moses Olatunji ◽  
Ojong Elias Ojong ◽  
...  
Keyword(s):  
Experimental Data ◽  
Isothermal Condition ◽  
Char Yield ◽  
Experimental Investigations ◽  
Time Saving ◽  
Pyrolysis Products ◽  
Pyrolysis Model ◽  
Experimental Yield ◽  
By Products ◽  
Good Agreement

AbstractNumerical modeling of biomass pyrolysis is becoming a cost and time-saving alternative for experimental investigations, also to predict the yield of the by-products of the entire process. In the present study, a two-step parallel kinetic model was used to predict char yield under isothermal condition. MATLAB ODE45 function codes were employed to solve a set of differential equations that predicts the %char at varying residence times and temperatures. The code shows how the various kinetic parameters and mass of pyrolysis products were determined. Nevertheless, the algorithm used for the prediction was validated with experimental data and results from past works. At 673.15 K, the numerical simulation using ODE45 function gives a char yield of 27.84%. From 573.15 K to 673.15 K, char yield ranges from 31.7 to 33.72% to 27.84% while experimental yield decreases from 44 to 22%. Hence, the error between algorithm prediction and experimental data from literature is − 0.26 and 0.22. Again, comparing the result of the present work with the analytical method from the literature showed a good agreement.

Sign in / Sign up

Export Citation Format

Share Document