scholarly journals Connection of infill panels in steel plate shear walls

1999 ◽  
Vol 26 (5) ◽  
pp. 549-563 ◽  
Author(s):  
A Schumacher ◽  
G Y Grondin ◽  
G L Kulak
Keyword(s):  
Finite Element ◽  
Cyclic Loading ◽  
Steel Plate ◽  
Shear Walls ◽  
Element Model ◽  
Shear Wall ◽  
Experimental Program ◽  
Steel Plate Shear Wall ◽  
Infill Panels ◽  
Welded Connection

The behaviour under cyclic loading of unstiffened steel plate shear wall panels at their connection to the bounding beams and columns was investigated on full-size panel corner details. Four different infill panel connection details were tested to examine and compare their response to quasi-static cyclic loading. The load versus displacement response of the details showed gradual and stable deterioration at higher loads. The formation of tears in the connection details did not result in a loss of load-carrying capacity. In addition to the experimental program, a finite element model was developed to model the behaviour of one of the infill plate corner connection specimens. Results from the analysis showed that the finite element method can be used to obtain the load versus displacement behaviour of an infill panel-to-boundary member arrangement.Key words: cyclic loading, hysteresis, shear wall, steel, welded connection.

An innovative system of coupled steel plate shear wall with pin FUSE in link beam: Cyclic behavior and energy dissipation

2021 ◽  
pp. 136943322110542
Author(s):  
Mahdi Usefvand ◽  
Ahmad Maleki ◽  
Babak Alinejad
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Energy Dissipation ◽  
Steel Plate ◽  
Shear Walls ◽  
Shear Wall ◽  
High Ductility ◽  
The Finite Element Method ◽  
Steel Plate Shear Walls ◽  
Steel Plate Shear Wall

Coupled steel plate shear wall (C-SPSW) is one of the resisting systems with high ductility and energy absorption capacity. Energy dissipation in the C-SPSW system is accomplished by the bending and shear behavior of the link beams and SPSW. Energy dissipation and floor displacement control occur through link beams at low seismic levels, easily replaced after an earthquake. In this study, an innovative coupled steel plate shear wall with a yielding FUSE is presented. The system uses a high-ductility FUSE pin element instead of a link beam, which has good replaceability after the earthquake. In this study, four models of coupled steel plate shear walls were investigated with I-shaped link beam, I-shaped link beam with reduced beam section (RBS), box-link beam with RBS, and FUSE pin element under cyclic loading. The finite element method was used through ABAQUS software to develop the C-SPSW models. Two test specimens of coupled steel plate shear walls were validated to verify the finite element method results. Comparative results of the hysteresis curves obtained from the finite element analysis with the experimental curves indicated that the finite element model offered a good prediction of the hysteresis behavior of C-SPSW. It is demonstrated in this study that the FUSE pin can improve and increase the strength and energy dissipation of a C-SPSW system by 19% and 20%, respectively.

scholarly journals Seismic Behavior of a Novel Buckling-Restrained Steel Plate Shear Wall

2021 ◽  
Vol 2021 ◽  
pp. 1-21 ◽  
Author(s):  
Yang Li ◽  
Xiaofeng Zhao ◽  
Ping Tan ◽  
Fulin Zhou ◽  
Jin Jiang
Keyword(s):  
Finite Element ◽  
Energy Dissipation ◽  
Finite Element Model ◽  
Steel Plate ◽  
Element Model ◽  
Shear Wall ◽  
Concrete Slabs ◽  
Test Results ◽  
Steel Plate Shear Wall ◽  
Hysteretic Characteristics

In this study, in a novel buckling-restrained steel plate shear wall (BRSPSW) with out-of-plane deformation spaces, angle steel stiffeners have been installed so as to create gaps between the steel plate and the covering concrete slabs. A finite element model has been developed to analyse the effect of the gap. According to the finite element results, seismic performance of this novel BRSPSW has been tested under cyclic loading at the scale ratio of 1/3. The failure pattern, hysteretic characteristics, skeleton curve, equivalent stiffness, ductility, and energy dissipation have all been systematically analysed. A stiffened steel plate shear wall (SPSW) has also been tested in order to determine the differences between these two steel shear walls in load-carrying capability and the function and significance of the gap. The test results show that the novel BRSPSW does not only significantly enhance the ultimate bearing capacity, stiffness, ductility, and accumulated energy dissipation of the SPSW but also keep the steel plate basically intact at the end of the test. This can be attributed to the existence of the gaps between the infilled steel plate and the covering concrete slabs. The hysteretic characteristics and the strength and deformation characteristics of this novel BRSPSW have been simulated by using the finite element model, and the test results are in good agreement with the finite element results. Hence, the BRSPSW is an excellent steel plate shear wall to be used in high rise structure to resist horizontal loadings.

scholarly journals Evaluation of Steel Plate Shear Wall Performance with Different Sections and Arrangements of Stiffeners and its Effect on Project Management during Construction and Improvement of the Building

2021 ◽  
Vol 11 (1) ◽  
pp. 6043-6063
Author(s):  
Ali Jafarian ◽  
Seyed Babak Jafarian
Keyword(s):  
Steel Plate ◽  
Nonlinear Dynamic Analysis ◽  
Shear Walls ◽  
Shear Wall ◽  
Economic Benefits ◽  
Lateral Loads ◽  
Steel Plate Shear Wall ◽  
High Rise ◽  
Earthquake Force ◽  
The Future

Considering the increase in the current construction process and the future needs of Iran, the necessity to use high-rise buildings for reduction in urbanization costs and optimal use of land will be inevitable in the future. The performance of steel plate shear wall system as a modern global system, which has an effective application in high-rise buildings and also brings economic benefits compared to previous systems, is evaluated in this study. Steel Plate Shear Walls (SPSW) are a new type of system resistant to wind and earthquake lateral loads, which dates back to the 1970s. In this research, eight samples of shear wall with various stiffening arrangements and sections with ST37 and ST52 alloys are modeled. To evaluate the nonlinear dynamic analysis, the samples are subjected to the San Fernando earthquake force and are modeled and analyzed by ABAQUS software based on the finite element theory. The results of analyzing the samples indicate better performance of the system with stiffener in both vertical and horizontal directions. Also, the use of sections with ST52 alloy has improved the performance of the shear wall by approximately 40%.

scholarly journals Effect of Corrugation Angle and Direction on the Performance of Corrugated Steel Plate Shear Walls

2018 ◽  
Vol 4 (11) ◽  
pp. 2667
Author(s):  
Hayder Fadhil ◽  
Amer Ibrahim ◽  
Mohammed Mahmood
Keyword(s):  
Steel Plate ◽  
Low Cost ◽  
Shear Walls ◽  
High Strength ◽  
Shear Wall ◽  
Initial Stiffness ◽  
Construction Time ◽  
Element Analysis ◽  
Steel Plate Shear Wall ◽  
Steel Shear Wall

Corrugated steel plate shear wall (CSPSW) is one of the lateral resistance systems which consists mainly of steel frame (beam and column) with vertical or horizontal corrugated steel plate connected to the frame by weld, bolts or both. This type of steel shear wall characterized by low cost and short construction time with high strength, ductility, initial stiffness and excellent ability to dissipate energy. The aim of this paper is to evaluate the effect of corrugation angle and its direction on the performance of CSPSW under cyclic loading. The Finite element analysis was employed to achieve the research aim. The FE models were validated with experimental data available in the literature. Results reveal that the corrugation angle has a clear influence on initial stiffness, strength, ductility, and energy dissipation of CSPSW. The optimum performance of CSPSW can be obtained with angles of 30o for CSPSW with vertical corrugation and 20o for CSPSW with horizontal corrugation. The use of CSPSW with vertical corrugation provides higher strength, stiffness, and ductility compared to CSPSW with horizontal corrugation. Therefore, it is recommended to use CSPSW with vertical corrugation.

SEISMIC LATERAL FORCE DISTRIBUTION FOR DUCTILITY-BASED DESIGN OF STEEL PLATE SHEAR WALLS

2012 ◽  
Vol 06 (01) ◽  
pp. 1250004 ◽  
Author(s):  
SWAPNIL B. KHARMALE ◽  
SIDDHARTHA GHOSH
Keyword(s):  
Steel Plate ◽  
Shear Walls ◽  
Shear Wall ◽  
Lateral Force ◽  
Performance Based Design ◽  
Force Distribution ◽  
Steel Plate Shear Walls ◽  
Steel Plate Shear Wall ◽  
Design Requirements ◽  
Ductility Ratio

The thin unstiffened steel plate shear wall (SPSW) system has now emerged as a promising lateral load resisting system. Considering performance-based design requirements, a ductility-based design was recently proposed for SPSW systems. It was felt that a detailed and closer look into the aspect of seismic lateral force distribution was necessary in this method. An investigation toward finding a suitable lateral force distribution for ductility-based design of SPSW is presented in this paper. The investigation is based on trial designs for a variety of scenarios where five common lateral force distributions are considered. The effectiveness of an assumed trial distribution is measured primarily on the basis of how closely the design achieves the target ductility ratio, which is measured in terms of the roof displacement. All trial distributions are found to be almost equally effective. Therefore, the use of any commonly adopted lateral force distribution is recommended for plastic design of SPSW systems.

Comparing Steel Plate Shear Wall Behavior with Simple and Corrugated Plates

2011 ◽  
Vol 147 ◽  
pp. 80-85 ◽  
Author(s):  
M. Gholizadeh ◽  
Y. Yadollahi
Keyword(s):  
Energy Absorption ◽  
Steel Plate ◽  
Hysteresis Loops ◽  
Shear Walls ◽  
Cost Effective ◽  
Shear Wall ◽  
Lateral Load ◽  
Absorption Capacity ◽  
Initial Stiffness ◽  
Steel Plate Shear Wall

Experimental and numerical studies conducted in the past three decades have demonstrated that a steel plate shear wall is an effective and economical lateral load resisting system against both wind and earthquake forces. The system consists of infill steel plates connected to boundary beams and columns over the full height of the framed bay. The infill plates can be stiffened or unstiffened and the beam-to-column connections can be rigid or shear connections. A properly designed steel plate shear wall has superior ductility, high initial stiffness, stable hysteresis loops, and good energy absorption capacity. These characteristics make the system outstanding in high-risk seismic regions. Use of steel plate shear wall systems has been shown to be more cost effective than the other lateral load resisting systems. Steel plate shear walls are much lighter than the commonly used reinforced concrete shear walls, which reduce both the gravity loads and seismic forces. This aspect significantly reduces the foundation costs and makes the system outstanding for application in rehabilitation projects. Whereas construction cost of stiffened steel plate shear wall is more than unstiffened steel plate shear wall therefore in this investigation the unstiffened steel plate shear wall has been studied as two types of simple and corrugated plate and the behavior has been compared in one story frame. This study was conducted with finite element approach theoretically. The results of this study demonstrated that behavior of corrugated plate is superior to simple plate because it has high loading capacity, ductility and energy absorption.

Unstiffened Steel Plate Shear Wall Performance under Cyclic Loading

2000 ◽  
Vol 126 (4) ◽  
pp. 453-460 ◽  
Author(s):  
Adam S. Lubell ◽  
Helmut G. L. Prion ◽  
Carlos E. Ventura ◽  
Mahmoud Rezai
Keyword(s):  
Cyclic Loading ◽  
Steel Plate ◽  
Shear Wall ◽  
Steel Plate Shear Wall
Sign in / Sign up

Export Citation Format

Share Document