Coliform inactivation in sludge by copper sulphate

1993 ◽  
Vol 20 (5) ◽  
pp. 814-819 ◽  
Author(s):  
D. Prasad ◽  
J. G. Henry ◽  
A. King

Studies were conducted to demonstrate the effectiveness of copper sulphate for disinfection of sewage sludge under anaerobic conditions. The effects of suspended solids and copper dosages on the survival of total coliforms in normal (neutral pH) and acidified sludges (pH 2.1–3.8) were studied. Results indicated that disinfection of sewage sludge by copper sulphate was feasible. Under anaerobic conditions, significant reductions (about 99%) of total coliform bacteria in normal sludge were achieved at a dosage of 40 mg Cu/g dry sludge mass, sludge suspended solids of < 3.0%, and a contact time of 24 h. The toxic effect of copper dosage was enhanced and the copper dosage and contact time reduced at lower pH (2.1–3.8). Sludge so treated would be suitable for land application insofar as its bacteriological quality is concerned, provided the high copper concentration could be reduced to acceptable levels. Whether this can be achieved in subsequent treatment of disinfected sludge by bacterial leaching will be determined in a future study. Key words: sludge disinfection, coliforms, copper sulphate, sludge disposal, bacterial leaching.

1991 ◽  
Vol 18 (2) ◽  
pp. 237-243 ◽  
Author(s):  
J. G. Henry ◽  
D. Prasad ◽  
W. B. Lohaza

Biological extraction (bacterial leaching) of heavy metals from digested sewage sludge has been shown to be a practical means for decontaminating sludge for use on agricultural land. However, it was not known whether pathogenic organisms would survive or be destroyed in the acidic environment necessary for the bacterial leaching process. The purpose of the research reported herein was to assess the effect of bacterial leaching on various bacteria commonly used to indicate the possible presence of pathogenic organisms. Although pathogenic viruses, bacteria, protozoa, and helminths may be present in sludge, this study is concerned only with bacterial pathogens. The concentrations of the four indicator bacteria selected to represent the bacterial pathogens were determined in a series of laboratory bacterial leaching units. Results showed that, although about 80–90% metal removal efficiencies were achieved (at a pH of 4.0, an aeration rate of 100 mL of air per minute per litre of sludge) at a temperature of 20–25 °C, the indicator bacteria were not reduced during bacterial leaching at high suspended solids concentrations. The survival of indicator bacteria was found to be a function of the suspended solids concentration in the leaching units, regardless of the source or type of indicator bacteria. At suspended solids concentrations greater than 10 g/L, the indicator bacteria were able to survive, apparently unaffected by the unfavourable environmental conditions (10 days retention at pH 4.0). Below this suspended solids concentration of 10 g/L, significant reductions of total coliforms, faecal coliforms, and faecal streptococci were achieved. Total heterotrophs did not follow the same trends as the other indicator bacteria. Key words: bacterial leaching, Thiobacillus ferrooxidans, indicator bacteria, enteric pathogens removal, sewage sludge, sludge disposal.


2016 ◽  
Vol 10 (1) ◽  
pp. 13-23 ◽  
Author(s):  
Agustina Arianita Cahyaningtyas ◽  
Wiwik Pudjiastuti ◽  
Ilham Ramdhan

One attempt to reduce the number of pathogenic microbes in milk is through the pasteurization process. This research aims to determine the effect of storage temperature on the organoleptic, acidity (pH) and growth of coliform bacteria in pasteurized milk. Pasteurized milk is stored at the varies of temperature  4°C (observed for 14 days), 10°C-15°C (observed for 14 days) and 25°C-27°C (observed for 22 hours), as well as also conducted an initial analysis pasteurized milk. The parameters were observed among other organoleptic (smell, taste, color, texture), pH and total coliform bacteria. Testing acidity using pH paper, while the growth of coliform bacteria testing done using Total Plate Count method based on ISO 2897 in 2008. The results of this study indicate that storage at 4°C for 14 days, organoleptic pasteurized milk is still good until the day ke- 8, pH progressively decreases, and the growth of coliform bacteria obtained the highest score of 3100x101 CFU / ml. Storage at 10°C-15°C for 14 days, organoleptic pasteurized milk is still good until the 6th day, the pH progressively decreases, and the growth of coliform bacteria obtained the highest score of 5729x101 CFU / ml. Storage at 25°C-27°C for 22 days, organoleptic pasteurized milk is still good until the 9th, pH progressively decreases, and the growth of coliform bacteria obtained the highest score of 4.3 x106 CFU / ml.ABSTRAKSalah satu usaha untuk mengurangi jumlah mikroba patogen pada susu adalah melalui proses pasteurisasi. Penelitian ini bertujuan untuk mengetahui pengaruh suhu penyimpanan terhadap organoleptik, derajat keasaman (pH) dan pertumbuhan bakteri Coliform pada susu pasteurisasi. Susu pasteurisasi disimpan pada suhu yang bervariasi yaitu suhu 4°C (diamati selama 14 hari), suhu 10°C-15°C (diamati selama 14 hari) dan suhu 25°C-27°C (diamati selama 22 jam), serta dilakukan pula analisa awal susu pasteurisasi. Parameter yang diamati antara lain organoleptik (bau, rasa, warna, tekstur), pH dan jumlah bakteri Coliform. Pengujian derajat keasaman menggunakan kertas pH, sedangkan pengujian pertumbuhan bakteri Coliform dilakukan dengan menggunakan metode Total Plate Count berdasarkan SNI 2897 Tahun 2008. Hasil penelitian ini menunjukkan bahwa penyimpanan pada suhu 4°C selama 14 hari, organoleptik susu pasteurisasi masih baik sampai dengan hari ke-8, pH semakin lama semakin menurun, dan pertumbuhan bakteri Coliform didapatkan nilai tertinggi sebesar 3100x101 Cfu/ml. Penyimpanan pada suhu 10°C-15°C selama 14 hari, organoleptik susu pasteurisasi masih baik sampai hari ke-6, pH semakin lama semakin menurun, dan pertumbuhan bakteri Coliform didapatkan nilai tertinggi sebesar 5729x101 Cfu/ml. Penyimpanan pada suhu 25°C-27°C selama 22 hari, organoleptik susu pasteurisasi masih baik sampai jam ke-9, pH semakin lama semakin menurun, dan pertumbuhan bakteri Coliform didapatkan nilai tertinggi sebesar 4,3 x106 Cfu/ml.Kata kunci : bakteri coliform, derajat keasaman, suhu penyimpanan, organoleptik, susu pasteurisasi


2013 ◽  
Vol 5 (1) ◽  
Author(s):  
Lies Indah Sutiknowati

The objective of this research was to evaluate waters quality in Pari island waters for aquaculture purpose based on bacteriological information conducted in Mei and September 2011. Microbiological parameters analyzed were total density of bacteria for coliforms, E.coli, pathogenic, heterotrophic, halotoleran, phosphate-nitrate-ammonia breaker, and total cells. Method to analyze coliform bacteria was filtration, identification of pathogenic bacteria using biochemical test, density analises for heterotrophic bacteria, analises for phosphate-nitrate-ammonia breaker bacteria using pour plate, and total cell using Acridine Orange Epifluorescence Microscopy. Results showed that the abundance of total coliform cell was about 1000-7000 colony forming unit (cfu)/100 ml. The abundance of heterotrophic, halotolerant, phosphate-nitrate-ammonia bacteria in seawater was (3.6-4.3)x105 cfu/ml, (1.1-1.3)x105 cfu/ml, (0.5-3.44)x103cfu/ml; and (3.6-6.7)x105 cfu/ml, (1.6-2.7)x105 cfu/ml, (0.6-5.22)x103 cfu/ml in sediment, respectively. The total cell of bacteria was (0.05-2.1)x107cells/ml. The dog-conch (Strombus turturella) and blood-clamps (Anadara granosa) can survive in Pari Island and there was a significant increase in sea grass litter with growth average of 0.67 mm/day and 0.90 mm/day. During snails and clamps growth, there were found several genus of pathogenic bacteria such as Salmonella, Vibrio, Aeromonas, Pseudomonas, Citrobacter, Proteus, Shigella, Hafnia, and Yersinia. The results showed that Pari island waters was suitable for developing shellfish aquaculture dog conch and blood clamps. Keywords: bacteria, parameter, shellfish, aquaculture.


1987 ◽  
Vol 19 (12) ◽  
pp. 265-271
Author(s):  
P. R. Thomas ◽  
H. O. Phelps

The investigation was based on two facultative stabilization ponds initially designed to operate in parallel, and now receive wastewater in excess of their capacities from a fast expanding housing estate in the Caribbean Island of Trinidad. Because of the deterioration of the effluent quality relative to acceptable standards, an attempt was made to upgrade the ponds using water hyacinths at the early stages. However, from the results, it was clear that the introduction of water hyacinths in the test pond did not lead to any substantial improvement in the effluent because of the high loading on the pond. Therefore the ponds were modified to operate in series with surface aerators installed in the first pond. Initially, the effluent quality was monitored in terms of total suspended solids, volatile suspended solids, biochemical oxygen demand, faecal coliform bacteria, pH and dissolved oxygen with aeration in the first pond and no aquatic plants in the second pond. Although there was a significant improvement in the effluent quality, the values remained above the standards. As a result, water hyacinths were introduced in the second pond and the effluent quality monitored together with aeration in the first pond. The effluent quality improved with total suspended solids and biochemical oxygen demand values both as low as 10 mg/l in certain months, but additional treatment was needed to reduce faecal conforms.


1995 ◽  
Vol 32 (2) ◽  
pp. 45-52 ◽  
Author(s):  
H. Z. Sarikaya ◽  
A. M. Saatçi

Total coliform bacteria have been chosen as the indicator organism. Coliform die-away experiments have been carried out in unpolluted sea water samples collected at about 100 m off the coastline and under controlled environmental conditions. The samples were transformed into one litre clean glass beakers which were kept at constant temperature and were exposed to the solar radiation. The membrane filter technique was used for the coliform analysis. The temperature ranged from 20 to 40° C and the dilution ratios ranged from 1/50 to 1/200. Coliform decay rate in the light has been expressed as the summation of the coliform decay rate in the dark and the decay rate due to solar radiation. The solar radiation required for 90 percent coliform removal has been found to range from 17 cal/cm2 to 40 cal/cm2 within the temperature range of 25 to 30° C. Applying the linear regression analysis two different equations have been given for the high (I&gt;10 cal/cm2.hour) and low solar intensity ranges in order to determine the coliform decay rate constant as a function of the solar intensity. T-90 values in the light have been found to follow log-normal distribution with a median T-90 value of 32 minutes. The corresponding T-90 values in the dark were found to be 70-80 times longer. Coliform decay rate in the dark has been correlated with the temperature.


2018 ◽  
Vol 53 (1) ◽  
pp. 77-82
Author(s):  
MA Riaz ◽  
B Ijaz ◽  
A Riaz ◽  
M Amjad

Present study aim to investigate application of microalgae for improvement of physiochemical parameters of waste water and improvement of treatment process through reducing the pollutant concentrations including coliform bacteria through their ability to uptake nutrients. Aquatic cultures were conducted in container with dimensions of 1.5×3sq ft. and wastewater samples 5 Litre samples were collected in plastic cans from Sukhnar drain and algal samples were collected from Bhaini Sigyain Village near Ravi Siphon, Lahore. The one experimental treatment lasted for 10 days to make 50% 5 liter water added concentration and 200g of inocula of algae were grown in wastewater container for experiments to optimize at room temperature as local outdoor cultures conditions for wastewater treatment. Total experiment repeated thrice and completed in 30 days. Results show that treatments improved the physiochemical parameter after week. Turbidity (NTU), total suspended solids (mg/L), total dissolved solids (mg/L), nitrate (mg/L), phosphate (mg/L) decrease (P < 0.05) after treatment. However, pH not significantly decreases (P≥ 0.05) pre-treatment values 6.56±0.05 (mg/L) and post-treatment 6.53± 0.057(mg/L). Maximum total coliform disinfection (P < 0.05) was indicated with 200 g of algae was pre-treatment 1602± 6.8 (MPN) and post treatment 1447±39.5 (MPN) observed.Bangladesh J. Sci. Ind. Res.53(1), 77-82, 2018


1993 ◽  
Vol 20 (1) ◽  
pp. 57-64 ◽  
Author(s):  
R. D. Tyagi ◽  
J. F. Blais ◽  
N. Meunier ◽  
D. Kluepfel

A biological process of heavy metals solubilization and sewage sludge stabilization was studied in a batch reactor of 30-L capacity. The acclimatized leaching microflora was composed of two major groups of thiobacilli: less acidophilic and acidophilic. A batch time of 10 days allows a substantial metal solubilization: cadmium (100%), copper (80%), manganese (80%), nickel (46%), and zinc (100%). The bioleaching process also causes a significative decrease in sludge total suspended solids (25%) and volatile suspended solids (32%), and a considerable reduction (under the detection limit of 10 cfu∙mL−1) of indicator bacteria (total coliforms, fecal coliforms, fecal streptococci). After filtration or centrifugation of the leached sludge, the solubilized metals were precipitated by lime neutralization. The phosphorus and potassium sludge contents were not affected by bioleaching process. These results indicate that the process of sludge digestion and metal leaching can be conducted in parallel in the same reactor. Key words: sewage sludge, heavy metals, bioleaching, stabilization, thiobacilli, elemental sulfur.


2017 ◽  
Vol 18 (3) ◽  
pp. 843-852
Author(s):  
Travis D. Gardner ◽  
Joe D. Guggenberger

Abstract Ceramic pot filters (CPFs) are an effective point of use water treatment device in developing nations due to their low cost and effectiveness. CPFs are gravity fed, typically making water production a major limiting factor to a CPF's lifetime and acceptability. Directly connecting CPFs to in-line pumping systems or systems with an elevated storage tank would allow filter usage for constant water treatment at increased pressures, increasing the quantity of treated water. Ceramic disks were manufactured for testing in a specially designed housing apparatus. Filters of varying thicknesses and clay to sawdust mass ratios were manufactured to fit tightly. Flowrate and microbiological removal efficacy (logarithmic reduction value (LRV)) were determined over the testing period at various pressures. Flowrate values ranged from 2.44 to 9.04 L per hour, significantly higher than traditional CPF technology. LRVs ranged from 1.1 to 2.0, lower than traditional CPF technology but still effective at removing most Escherichia coli and total coliform bacteria. Filters proved effective at removing total and fecal coliforms at pressures less than 70 kilopascals. The optimum filter had a thickness of 3.2 cm and clay to sawdust ratio of 6:1 by mass. Filters proved to be ineffective if flowrates were above 5 L/h.


Sign in / Sign up

Export Citation Format

Share Document