scholarly journals Dynamic testing of a modern concrete bridge

1979 ◽  
Vol 6 (3) ◽  
pp. 447-455 ◽  
Author(s):  
J. H. Rainer ◽  
G. Pernica
Keyword(s):  
Natural Frequencies ◽  
Dynamic Testing ◽  
Dynamic Properties ◽  
Mode Shapes ◽  
Total Width ◽  
Concrete Bridge ◽  
Reinforced Concrete Bridge ◽  
Natural Modes ◽  
Modes Of Vibration ◽  
Good Agreement

A posttensioned reinforced concrete bridge, slated for demolition, was tested to obtain its dynamic properties. The 10 year old bridge consisted of a continuous flat slab deck of variable thickness having a total width of 103 ft (31.39 m) and spans of 28 ft 6 in. (8.69 m), 71 ft 0 in. (21.64 m), and 42 ft 6 in. (12.95 m). The entire bridge was skewed 10°50′ and the deck was slightly curved in plan.The mode shapes, natural frequencies, and damping ratios for the lowest five natural modes of vibration were determined using sinusoidal forcing functions from an electrohydraulic shaker. These modes, located at 5.7, 6.4, 8.7, 12.0, and 17.4 Hz, were found to be highly dependent on the lateral properties of the bridge deck. Damping ratios were determined from the widths of resonance peaks. The modal properties from the steady state excitation were compared with those obtained from measurements of traffic-induced vibrations and good agreement was found between the two methods.

scholarly journals Influence of Excitation on Dynamic System Identification for a Multi-Span Reinforced Concrete Bridge

2009 ◽  
Vol 2009 ◽  
pp. 1-18 ◽  
Author(s):  
M. Alwash ◽  
B. F. Sparling ◽  
L. D. Wegner
Keyword(s):  
Reinforced Concrete ◽  
Natural Frequencies ◽  
Harmonic Excitation ◽  
Dynamic Responses ◽  
Mode Shapes ◽  
Concrete Bridge ◽  
Random Loading ◽  
Reinforced Concrete Bridge ◽  
Random Forcing ◽  
Vehicle Loading

In vibration-based damage detection, changes to structural modal properties are tracked over time in order to infer the current state of damage or deterioration. As such, the ability to obtain reliable estimates of modal parameters, particularly natural frequencies and mode shapes, is of critical importance. In the present study, the influence of the dynamic excitation source on the accuracy and statistical uncertainty of modal property estimates for a three span reinforced concrete bridge was investigated experimentally and numerically. Comparisons were made between the dynamic responses due to vehicle loading, harmonic and random forcing, impact, and environmental excitation. It was demonstrated that natural frequencies and mode shapes extracted from the free vibration response following vehicle and random loading events were of higher quality than corresponding values determined during the forcing phase of those events. Harmonic excitation at resonant frequencies and impact were also found to produce statistically reliable results.

Tire Vibrations

1977 ◽  
Vol 5 (4) ◽  
pp. 202-225 ◽  
Author(s):  
G. R. Potts ◽  
C. A. Bell ◽  
L. T. Charek ◽  
T. K. Roy
Keyword(s):  
Natural Frequencies ◽  
Standing Waves ◽  
Resonant Mode ◽  
Mode Shapes ◽  
Resonant Vibrations ◽  
Resonant Frequencies ◽  
Radial Tire ◽  
Analysis Techniques ◽  
Thin Ring ◽  
Good Agreement

Abstract Natural frequencies and vibrating motions are determined in terms of the material and geometric properties of a radial tire modeled as a thin ring on an elastic foundation. Experimental checks of resonant frequencies show good agreement. Forced vibration solutions obtained are shown to consist of a superposition of resonant vibrations, each rotating around the tire at a rate depending on the mode number and the tire rotational speed. Theoretical rolling speeds that are upper bounds at which standing waves occur are determined and checked experimentally. Digital Fourier transform, transfer function, and modal analysis techniques used to determine the resonant mode shapes of a radial tire reveal that antiresonances are the primary transmitters of vibration to the tire axle.

Dynamic model for high-speed rotors based on their experimental characterization

2017 ◽  
Vol 2 (4) ◽  
pp. 25
Author(s):  
L. A. Montoya ◽  
E. E. Rodríguez ◽  
H. J. Zúñiga ◽  
I. Mejía
Keyword(s):  
Dynamic Model ◽  
High Speed ◽  
Natural Frequencies ◽  
Mode Shapes ◽  
Experimental Characterization ◽  
Rotating Systems ◽  
Computing Performance ◽  
The Impact ◽  
Stiffness Distribution ◽  
Good Agreement

Rotating systems components such as rotors, have dynamic characteristics that are of great importance to understand because they may cause failure of turbomachinery. Therefore, it is required to study a dynamic model to predict some vibration characteristics, in this case, the natural frequencies and mode shapes (both of free vibration) of a centrifugal compressor shaft. The peculiarity of the dynamic model proposed is that using frequency and displacements values obtained experimentally, it is possible to calculate the mass and stiffness distribution of the shaft, and then use these values to estimate the theoretical modal parameters. The natural frequencies and mode shapes of the shaft were obtained with experimental modal analysis by using the impact test. The results predicted by the model are in good agreement with the experimental test. The model is also flexible with other geometries and has a great time and computing performance, which can be evaluated with respect to other commercial software in the future.

Fluid Added Mass Effect in the Modal Response of a Pump-Turbine Impeller

2009 ◽  
Author(s):  
Eduard Egusquiza ◽  
Carme Valero ◽  
Quanwei Liang ◽  
Miguel Coussirat ◽  
Ulrich Seidel
Keyword(s):  
Natural Frequencies ◽  
Experimental Tests ◽  
Mass Effect ◽  
Added Mass ◽  
Mode Shapes ◽  
Pump Turbine ◽  
Modal Response ◽  
Surrounding Fluid ◽  
Turbine Impeller ◽  
Good Agreement

In this paper, the reduction in the natural frequencies of a pump-turbine impeller prototype when submerged in water has been investigated. The impeller, with a diameter of 2.870m belongs to a pump-turbine unit with a power of around 100MW. To analyze the influence of the added mass, both experimental tests and numerical simulations have been carried out. The experiment has been performed in air and in water. From the frequency response functions the modal characteristics such as natural frequencies and mode shapes have been obtained. A numerical simulation using FEM (Finite Elements Model) was done using the same boundary conditions as in the experiment (impeller in air and surrounded by a mass of water). The modal behaviour has also been calculated. The numerical results were compared with the available experimental results. The comparison shows a good agreement in the natural frequency values both in air and in water. The reduction in frequency due to the added mass effect of surrounding fluid has been calculated. The physics of this phenomenon due to the fluid structure interaction has been investigated from the analysis of the mode-shapes.

Natural Frequencies and Mode Shapes of Elliptic Plates With Boundary Characteristic Orthogonal Polynomials As Assumed Shape Functions

1991 ◽  
Author(s):  
C. Rajalingham ◽  
R. B. Bhat ◽  
G. D. Xistris
Keyword(s):  
Coordinate System ◽  
Orthogonal Polynomials ◽  
Natural Frequencies ◽  
Ritz Method ◽  
Mode Shapes ◽  
Polar Coordinate System ◽  
Free Boundaries ◽  
Natural Modes ◽  
Polar Coordinate ◽  
Boundary Characteristic

Abstract The natural frequencies and natural modes of vibration of uniform elliptic plates with clamped, simply supported and free boundaries are investigated using Rayleigh-Ritz method. A modified polar coordinate system is used to investigate the problem. Energy expressions in Cartesian coordinate system are transformed into the modified polar coordinate system. Boundary characteristic orthogonal polynomials in the radial direction, and trigonometric functions in the angular direction are used to express the deflection of the plate. These deflection shapes are classified into four basic categories, depending on its symmetrical or antisymmetrical property about the major and minor axes of the ellipse. The first six natural modes in each of the above categories are presented in the form of contour plots.

scholarly journals The seismic performance of steel encased reinforced concrete bridge piles

1983 ◽  
Vol 16 (2) ◽  
pp. 123-140
Author(s):  
R. J. T. Park ◽  
M. J. N. Priestley ◽  
W. R. Walpole
Keyword(s):  
Reinforced Concrete ◽  
Seismic Performance ◽  
Theoretical Investigation ◽  
Axial Load ◽  
Lateral Displacement ◽  
Load Level ◽  
Concrete Bridge ◽  
Reinforced Concrete Bridge ◽  
Outside Diameter ◽  
Good Agreement

An experimental and theoretical investigation into the seismic performance of steel encased reinforced concrete bridge piles is described. Six test units were designed, constructed and tested
under cyclic lateral displacement-controlled loading. The units had
an outside diameter of 360 mm and a steel casing thickness of 5 mm. Variables included the axial load level, inclusion or exclusion of internal reinforcing cages, and the influence of the casing continuity at he critical flexural sections. Sound seismic performance was observed in all of the models and good agreement between predicted and observed ultimate behaviour was obtained.

Vibrational characteristics of an earth dam

1966 ◽  
Vol 56 (6) ◽  
pp. 1207-1226
Author(s):  
W. O. Keightley
Keyword(s):  
Theoretical Analysis ◽  
Natural Frequencies ◽  
Forced Vibrations ◽  
Earth Dam ◽  
Mode Shapes ◽  
Modal Damping ◽  
Vibrational Characteristics ◽  
Good Agreement ◽  
Lower Frequencies

Abstract An earth dam was excited into vibrations, in the upstream-downstream direction, by four rotating eccentric-mass vibration generators which were operated on the crest. Natural frequencies, mode shapes, and equivalent viscous modal damping constants of the dam were revealed by the forced vibrations. A theoretical analysis of the dam, based on consideration of shearing deformations only, shows moderately good agreement with the behavior which was observed at the lower frequencies.

Design and Analysis of Foldable Vehicle using Finite Element Simulation

2021 ◽  
Vol 13 (3) ◽  
Author(s):  
Vikas Radhakrishna Deulgaonkar ◽  
S.N. Belsare ◽  
Naik Shreyas ◽  
Dixit Pratik ◽  
Kulkarni Pranav ◽  
...  
Keyword(s):  
Finite Element ◽  
Dynamic Properties ◽  
Mode Shapes ◽  
Vehicle Speed ◽  
Element Analysis ◽  
Dynamic Stresses ◽  
Element Simulation ◽  
Vehicle Structure ◽  
Similar Materials ◽  
Good Agreement

Present work deals with evaluation of stress, deflection and dynamic properties of the folded vehicle structure. The folded vehicle in present case is a single seat vehicle intended to carry one person. Design constraints are the folded dimensions of the vehicle and the maximum vehicle speed is limited to 15m/s. Using classical calculations dimensions of the vehicle are devised. Different materials are used for seat, telescopic support and chassis of the foldable vehicle. computer aided model is prepared using CATIA software. Finite element analysis of the foldable vehicle has been carried out to evaluate the static and dynamic stresses induced in the vehicle components. Meshing of the foldable vehicle is carried using Ansys Workbench. From modal analysis six mode shapes of the foldable vehicle are formulated, corresponding frequencies and deflections are devised. Mesh generator is used to mesh the foldable vehicle. The deflection and frequency magnitudes of foldable vehicle evaluated are in good agreement with the experimental results available in literature for similar materials.

Free Vibrations of Constrained Beams

1952 ◽  
Vol 19 (4) ◽  
pp. 471-477
Author(s):  
Winston F. Z. Lee ◽  
Edward Saibel
Keyword(s):  
Natural Frequencies ◽  
Degree Of Approximation ◽  
Free Vibrations ◽  
Frequency Equation ◽  
Continuous Beam ◽  
Concentrated Mass ◽  
Simple Manner ◽  
Natural Modes ◽  
Modes Of Vibration ◽  
Rigid Supports

Abstract A general expression is developed from which the frequency equation for the vibration of a constrained beam with any combination of intermediate elastic or rigid supports, concentrated masses, and sprung masses can be found readily. The method also is extended to the case where the constraint is a continuous elastic foundation or uniformly distributed load of any length. This method requires only the knowledge of the natural frequencies and natural modes of the beam supported at the ends in the same manner as the constrained beam but not subjected to any of the constraints between the ends. The frequency equation is obtained easily and can be solved to any desired degree of approximation for any number of modes of vibration in a quick and simple manner. Numerical examples are given for a beam with one concentrated mass, for a beam with one sprung mass, and a continuous beam with one sprung mass.

scholarly journals A space structural mechanics model of silicene

2020 ◽  
Vol 234 (1-2) ◽  
pp. 3-10
Author(s):  
Mohsen Motamedi
Keyword(s):  
Natural Frequencies ◽  
Strain Curve ◽  
Structural Mechanics ◽  
Dynamics Simulation ◽  
Mode Shapes ◽  
Two Dimensional ◽  
Stress Strain Curve ◽  
Beam Elements ◽  
Mechanics Model ◽  
Good Agreement

The two-dimensional nanostructures such as graphene, silicene, germanene, and stanene have attracted a lot of attention in recent years. Many studies have been done on graphene, but other two-dimensional structures have not yet been studied extensively. In this work, a molecular dynamics simulation of silicene was done and stress–strain curve of silicene was obtained. Then, the mechanical properties of silicene were investigated using the proposed structural molecular mechanics method. First, using the relations governing the force field and the Lifson–Wershel potential function and structural mechanics relations, the coefficients for the BEAM elements was determined, and a structural mechanics model for silicene was proposed. Then, a silicene sheet with 65 Å × 65 Å was modeled, and Young’s modulus of silicene was obtained. In addition, the natural frequencies and mode shapes of silicene were calculated using finite element method. The results are in good agreement with reports by other papers.

Sign in / Sign up

Export Citation Format

Share Document