3D modelling of ice-covered flows in the vicinity of a deep hole in the East Channel of the Mackenzie Delta, N.W.T.

2009 ◽  
Vol 36 (5) ◽  
pp. 791-800 ◽  
Author(s):  
Chris Inkratas ◽  
Bahram Gharabaghi ◽  
Spyros Beltaos ◽  
Bommanna Krishnappan
Keyword(s):  
Initial Assessment ◽  
Mackenzie Delta ◽  
Stress Distributions ◽  
Deep Hole ◽  
Cfd Model ◽  
Flow Conditions ◽  
Single Vortex ◽  
Wall Functions ◽  
Computational Fluid Dynamics Cfd ◽  
The Stability

The discovery of vast quantities of hydrocarbons during exploration of the Mackenzie Delta has led to the detection of numerous anomalous deep holes in various delta channels in the past four decades. The proposed pipeline crossing from the Mackenzie Delta to northern Alberta has renewed interest in studying the stability of these deep holes. The main goal of this research project was to study ice-covered flow velocity and bed shear stress distributions using a previously calibrated computational fluid dynamics (CFD) model for a 30 m deep hole in the East Channel of the Mackenzie Delta to provide an initial assessment of its stability. In this study, a previously developed 3D CFD model using the FLUENT code with the renormalization group theory (RNG) k-ε turbulence closure model with nonequilibrium wall functions was adapted to represent ice-covered flow conditions for the study reach. The numerical model was applied to simulate four flow conditions (500, 720, and 1000 m3/s along with a moving ice cover during a flow rate of 720 m3/s). Results indicated that a single vortex was formed near the inner bend above the hole and deposition may be a key process occurring during ice-covered flow conditions.

Modelling of three-dimensional flow velocities in a deep hole in the East Channel of the Mackenzie Delta, Northwest Territories

2007 ◽  
Vol 34 (10) ◽  
pp. 1312-1323 ◽  
Author(s):  
Bahram Gharabaghi ◽  
Chris Inkratas ◽  
Spyros Beltaos ◽  
Bommanna Krishnappan
Keyword(s):  
Shear Stress ◽  
Three Dimensional ◽  
Bed Shear Stress ◽  
Mackenzie Delta ◽  
Stress Distributions ◽  
Deep Hole ◽  
Flow Conditions ◽  
Scour Hole ◽  
Scour Holes ◽  
The Stability

The Mackenzie River has several anomalous deep scour holes in a number of river channels in its delta. Proposed gas pipeline crossings have renewed interest in studying the stability of these scour holes. The main goal of this research project was to study flow velocity and bed shear stress distributions for a 30 m deep hole in the East Channel of the Mackenzie Delta as a first step toward assessing the stability of the scour hole and the risk of its migration during various flow conditions. In this study, a three-dimensional (3D) finite element flow model, FLUENT, using the renormalization group (RNG) k-ε turbulence model (where k is the turbulent kinetic energy and ε is the turbulence dissipation rate) was set up for the scour hole and calibrated using detailed measurements of 3D flow velocities, obtained with an acoustic doppler current profiler. The numerical model was then applied to predict flow velocity and bed shear stress distributions in and around the scour hole for three flow conditions (720, 1000, and 1400 m3/s). Results indicate that two vortices are formed in the river elbow above the scour hole. As the flow rate changed, the sizes of the vortices varied. The region upstream of the hole experienced the greatest magnitudes of bed shear stress.Key words: computational fluid dynamics, finite element, bed shear stress, deep hole, flow reversal.

Gland Seal Erosion in a Geothermal Turbine

2003 ◽  
Author(s):  
Zdzislaw Mazur ◽  
Luis M. Palacios ◽  
Gustavo Urquiza
Keyword(s):  
Fluid Dynamics ◽  
Solid Particles ◽  
Steam Flow ◽  
Cfd Model ◽  
Flow Conditions ◽  
System Flow ◽  
Gland Seal ◽  
Rotor Surface ◽  
Computational Fluid Dynamics Cfd ◽  
Flow Pressure

Excessive erosion of the low-pressure shaft end gland seal of a 25 MW geothermal turbine has been investigated. Due to excessive erosion of the gland seal rotor surface the turbine vacuum was partially destroyed and the efficiency of the cycle degraded. This study uses computational fluid dynamics (CFD) to identify the causes of erosion and the optimal steam seal system flow conditions for reducing the erosion problem. The predictions were based upon a numerical calculation using a CFD model of the rotor end gland seal with a steam flow containing hard solid particles and solved with the commercial CFD code: Adapco STAR-CD. The results confirmed the existence of flow conditions that play a major role in the rotor gland seal erosion. Afterwards, the flow was simulated changing seal steam flow conditions (flow pressure). It was confirmed that there exists threshold seal flow conditions below which erosion does not occur. The recommendations for adjusting shaft end gland seal system are provided to avoid erosion problem.

Effects of Over Fire Air on the Combustion and NOx Emission Characteristics of a 600 MW Opposed Swirling Fired Boiler

2012 ◽  
Vol 512-515 ◽  
pp. 2135-2142 ◽  
Author(s):  
Yu Peng Wu ◽  
Zhi Yong Wen ◽  
Yue Liang Shen ◽  
Qing Yan Fang ◽  
Cheng Zhang ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Experimental Data ◽  
Empirical Method ◽  
Nox Emission ◽  
Emission Characteristics ◽  
Cfd Model ◽  
Nitrogen Release ◽  
Computational Fluid Dynamics Cfd ◽  
Low Nox Emission

A computational fluid dynamics (CFD) model of a 600 MW opposed swirling coal-fired utility boiler has been established. The chemical percolation devolatilization (CPD) model, instead of an empirical method, has been adapted to predict the nitrogen release during the devolatilization. The current CFD model has been validated by comparing the simulated results with the experimental data obtained from the boiler for case study. The validated CFD model is then applied to study the effects of ratio of over fire air (OFA) on the combustion and nitrogen oxides (NOx) emission characteristics. It is found that, with increasing the ratio of OFA, the carbon content in fly ash increases linearly, and the NOx emission reduces largely. The OFA ratio of 30% is optimal for both high burnout of pulverized coal and low NOx emission. The present study provides helpful information for understanding and optimizing the combustion of the studied boiler

Validation of a Computationally Efficient Computational Fluid Dynamics (CFD) Model for Industrial Bubble Column Bioreactors

2014 ◽  
Vol 53 (37) ◽  
pp. 14526-14543 ◽  
Author(s):  
Dale D. McClure ◽  
Hannah Norris ◽  
John M. Kavanagh ◽  
David F. Fletcher ◽  
Geoffrey W. Barton
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Bubble Column ◽  
Cfd Model ◽  
Computationally Efficient ◽  
Computational Fluid Dynamics Cfd

Investigation of sustainability of lubricated journal bearing under relevant design parameters

2018 ◽  
Vol 70 (4) ◽  
pp. 789-804 ◽  
Author(s):  
M.M. Shahin ◽  
Mohammad Asaduzzaman Chowdhury ◽  
Md. Arefin Kowser ◽  
Uttam Kumar Debnath ◽  
M.H. Monir
Keyword(s):  
Aspect Ratio ◽  
Elastic Strain ◽  
Journal Bearing ◽  
Design Parameters ◽  
Content Type ◽  
Computational Fluid Dynamics Cfd ◽  
Stress Formation ◽  
Bearing Design ◽  
The Stability ◽  
Bearing Friction

Purpose The purposes of the present study are to ensure higher sustainability of journal bearings under different applied loads and to observe bearing performances such as elastic strain, total deformation and stress formation. Design/methodology/approach A journal bearing test rig was used to determine the effect of the applied load on the bearing friction, film thickness, lubricant film pressure, etc. A steady-state analysis was performed to obtain the bearing performance. Findings An efficient aspect ratio (L/D) range was obtained to increase the durability or the stability of the bearing while the bearing is in the working condition by using SAE 5W-30 oil. The results from the study were compared with previous studies in which different types of oil and water, such as Newtonian fluid (NF), magnetorheological fluid (MRF) and nonmagnetorheological fluid (NMRF), were used as the lubricant. To ensure a preferable aspect ratio range (0.25-0.50), a computational fluid dynamics (CFD) analysis was conducted by ANSYS; the results show a lower elastic strain and deformation within the preferable aspect ratio (0.25-0.50) rather than a higher aspect ratio using the SAE 5W-30 oil. Originality/value It is expected that the findings of this study will contribute to the improvement of the bearing design and the bearing lubricating system.

The Stability of Flow Through Porous Screens

1960 ◽  
Vol 64 (594) ◽  
pp. 359-362 ◽  
Author(s):  
P. G. Morgan
Keyword(s):  
Pressure Drop ◽  
Sufficient Information ◽  
Flow Conditions ◽  
Flow Through ◽  
The Stability

In many cases of the flow through porous screens, one may consider it to be made up of a number of jets passing through the openings of the screen. These jets are separated by a series of wakes behind the solid parts of the screen. The majority of investigations on the flow through such screens have been concerned with the measurement of pressure drop and its variation with different flow conditions; it has been assumed that the pressure is discontinuous at the screen itself and that the pressure drop coefficient Δp/½ρυ2 provides sufficient information, where Δp is the pressure drop across the screen, ρ the density of the fluid, and υ the velocity of approach to the screen.

An Integrated Ship Re-Design/Modification Strategy

2019 ◽  
Vol 161 (A1) ◽  
Keyword(s):  
Computer Aided Design ◽  
Modular Design ◽  
Ship Hull ◽  
Cfd Model ◽  
Hull Form ◽  
Design Modification ◽  
Technical Parameters ◽  
Computational Fluid Dynamics Cfd ◽  
Bulbous Bow ◽  
Aided Design

Herein, we present an integrated ship re-design/modification strategy that integrates the ‘Computer-Aided Design (CAD)’ and ‘Computational Fluid Dynamics (CFD)’ to modify the ship hull form for better performance in resistance. We assume a modular design and the ship hull form modification focuses on the forward module (e.g. bulbous bow) and aft module (e.g. stern bulb) only. The ship hull form CAD model is implemented with NAPA*TM and CFD model is implemented with Shipflow**TM. The basic ship hull form parameters are not changed and the modifications in some of the technical parameters because of re-designed bulbous bow and stern bulb are kept at very minimum. The bulbous bow is re-designed by extending an earlier method (Sharma and Sha (2005b)) and stern bulb parameters for re-design are computed from the experience gained from literature survey. The re-designed hull form is modeled in CAD and is integrated and analyzed with Shipflow**TM. The CAD and CFD integrated model is validated and verified with the ITTC approved recommendations and guidelines. The proposed numerical methodology is implemented on the ship hull form modification of a benchmark ship, i.e. KRISO container ship (KCS). The presented results show that the modified ship hull form of KCS - with only bow and stern modifications - using the present strategy, results into resistance and propulsive improvement.

Sign in / Sign up

Export Citation Format

Share Document