Finite element studies of reinforced concrete slab - edge column connections with openings

2007 ◽  
Vol 34 (8) ◽  
pp. 952-965 ◽  
Author(s):  
Hong Guan ◽  
Maria Anna Polak
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Large Scale ◽  
Numerical Study ◽  
Concrete Slab ◽  
Reinforced Concrete Slab ◽  
Element Analysis ◽  
Numerical Studies ◽  
Experimental Findings ◽  
Good Agreement

An extended nonlinear layered finite element method (LFEM) is used to investigate the influence of openings and shear stud reinforcement (SSR) on the behaviour of reinforced concrete slab – edge column connections. In all, ten large-scale slab – edge column connections tested previously are analyzed. The laboratory test variables were the size and location of the openings in the vicinity of an edge column and the existence of SSR. The numerical results of the load–deflection response, the ultimate strength, and the crack patterns are compared with the experimental findings and good agreement is achieved. A numerical study on two connections is also carried out to determine the influence of the locations of opening in slab – edge column connections with SSR. Discussion on code provisions for slabs with openings is provided. The comparative and numerical studies confirm the accuracy, reliability, and effectiveness of the LFEM in the analysis of slab – edge column connections with both openings and SSR.Key words:slab–column connection, punching shear, opening, shear stud reinforcement, finite element analysis.

Microcomputer analysis of reinforced concrete slab systems

1993 ◽  
Vol 20 (4) ◽  
pp. 587-601 ◽  
Author(s):  
Pierre Léger ◽  
Patrick Paultre
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Structural Design ◽  
Concrete Slab ◽  
Three Dimensional ◽  
Structural Behaviour ◽  
Reinforced Concrete Slab ◽  
Element Analysis ◽  
Equivalent Frame ◽  
Frame Method

Microcomputer finite element analysis of reinforced concrete slab systems can now be routinely performed to produce realistic numerical simulation of three-dimensional structural behaviour. However, an efficient use of this approach requires an automated integration of design and analysis procedures. Guidelines for proper finite element modelling of slab systems are first presented along with simple post-processing algorithms to perform automatically the design or verifications from the analytical results. Numerical applications on simple slab systems subjected to uniform and concentrated loads are then used to illustrate the relative performance between finite element analyses and the equivalent frame method. Key words: microcomputer, reinforced concrete slab, finite element method, structural design.

scholarly journals Finite element analysis of flexural behavior of textile reinforced concrete slab

2021 ◽  
Vol 261 ◽  
pp. 02042
Author(s):  
Mingqiu Xu ◽  
Jianhua Shao ◽  
Baijian Tang ◽  
Hongming Li
Keyword(s):  
Finite Element ◽  
Reinforced Concrete ◽  
Finite Element Model ◽  
Concrete Slab ◽  
Element Model ◽  
Flexural Behavior ◽  
Textile Reinforced Concrete ◽  
Reinforced Concrete Slab ◽  
Element Analysis ◽  
Bending Load

Order to investigate the failure effect of textile reinforced concrete (TRC) plate under bending load, the corresponding finite element model is established. By comparing the numerical simulation results with the experimental results, the rationality and feasibility of the finite element model are verified, and then the crack extension of TRC and the ultimate strain of carbon textile are analyzed. The failure mode of the slab under bending load is obtained, and it is found that the carbon textile concrete slab has better reinforcement effect, which greatly improves the safety performance of concrete members.

scholarly journals Numerical Modelling of One-Way Reinforced Concrete Slab in FireTaking Into Account of Spalling

2021 ◽  
Vol 7 (3) ◽  
pp. 477-487
Author(s):  
Guergah Cherif ◽  
Dimia Mohamed Salah ◽  
Benmarce Abdelaziz
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Mechanical Response ◽  
Concrete Slab ◽  
Fire Exposure ◽  
Reinforced Concrete Slab ◽  
Element Analysis ◽  
Finite Element Software ◽  
Rc Slabs

This paper presents a study of the behaviour of Reinforced Concrete (RC) slabs subjected to severe hydrocarbon fire exposure. In which the spalling phenomena of concrete is to be considered. The hydrocarbon curve is applicable where small petroleum fires might occur, i.e. car fuel tanks, petrol or oil tankers, certain petro-chemical facilities, tunnels, parking structures, etc. Spalling is included using a simplified approach where elements with temperatures higher than 400 °C are assumed to occur and the corresponding thermo-mechanical response of RC slabs is evaluated. The nonlinear finite element software SAFIR has been used to perform a numerical analysis of the spalling risk, by removing layers of concrete covering when a set of spalling criteria is checked. The numerical results obtained by finite element analysis of the temperature distribution within the slab and mid-span deflection were compared with published experimental data. Predictions from the numerical model show a good agreement with the experimental data throughout the entire fire exposure to the hydrocarbon fire. This shows that this approach (layering procedure) is very useful in predicting the behaviour of concrete spalling cases. Doi: 10.28991/cej-2021-03091667 Full Text: PDF

Experimental, numerical and parametric studies on stress concentration factors of T-joints under tension

2021 ◽  
pp. 136943322110499
Author(s):  
Feleb Matti ◽  
Fidelis Mashiri
Keyword(s):  
Finite Element ◽  
Stress Concentration ◽  
Numerical Study ◽  
Hot Spot ◽  
Joint Models ◽  
Element Analysis ◽  
T Joints ◽  
Concentration Factors ◽  
Stress Concentration Factors ◽  
Good Agreement

This paper investigates the behaviour of square hollow section (SHS) T-joints under static axial tension for the determination of stress concentration factors (SCFs) at the hot spot locations. Five empty and corresponding concrete-filled SHS-SHS T-joint connections were tested experimentally and numerically. The experimental investigation was carried out by attaching strain gauges onto the SHS-SHS T-joint specimens. The numerical study was then conducted by developing three-dimensional finite element (FE) T-joint models using ABAQUS finite element analysis software for capturing the distribution of the SCFs at the hot spot locations. The results showed that there is a good agreement between the experimental and numerical SCFs. A series of formulae for the prediction of SCF in concrete-filled SHS T-joints under tension were proposed, and good agreement was achieved between the maximum SCFs in SHS T-joints calculated from FE T-joint models and those from the predicted formulae.

scholarly journals Experimental Study on Mechanical Property of Stiffening-ribbed-hollowpipe Reinforced Concrete Girderless Floor with Four Clamped Edges Supported

2013 ◽  
Vol 7 (1) ◽  
pp. 170-178 ◽  
Author(s):  
Weijun Yang ◽  
Yongda Yang ◽  
Jihua Yin ◽  
Yushuang Ni
Keyword(s):  
Mechanical Property ◽  
Finite Element Analysis ◽  
Finite Element ◽  
Reinforced Concrete ◽  
Large Scale ◽  
Load Test ◽  
Static Load Test ◽  
Loading Test ◽  
Element Analysis ◽  
Clamped Edges

In order to study the basic mechanical property of cast-in-place stiffening-ribbed-hollow-pipe reinforced concrete girderless floor, and similarities and differences of the structural performance compared with traditional floor, we carried out the destructive stage loading test on the short-term load test of floor model with four clamped edges supported in large scale, and conducted the long-term static load test. Also, the thesis conducted finite element analysis in virtue of ANSYS software for solid slab floor, stiffening-ribbed-hollow-pipe floor and tubular floor. The experiment indicates that the developing process of cracks, distribution and failure mode in stiffening-ribbed-hollow-pipe floor are similar to that of solid girderless floor, and that this kind of floor has higher bearing capacity and better plastic deformation capacity. The finite element analysis manifests that, compared with solid slab floor, the deadweight of stiffening-ribbed-hollow-pipe floor decreases on greater level while deformation increases little, and that compared with tubular floor, this floor has higher rigidity. So stiffening-ribbed-hollow-pipe reinforced concrete girderless floor is particularly suitable for long-span and large-bay building structure.

Sign in / Sign up

Export Citation Format

Share Document