THE EFFECT OF SULPHITE LIQUOR COMPOSITION ON THE RATE OF DELIGNIFICATION OF SPRUCE WOOD AND YIELD OF PULP

1937 ◽  
Vol 15b (11) ◽  
pp. 457-474 ◽  
Author(s):  
J. M. Calhoun ◽  
F. H. Yorston ◽  
O. Maass

A technique has been devised for studying the delignification of wood in sulphite liquor under accurately controlled conditions. The rate of delignification of resin extracted spruce wood-meal has been determined at 130 °C. over the concentration range 0.2 to 1.4% combined, and 2 to 14% total, sulphur dioxide. The reaction shows a systematic deviation from the first order relation that is the same for any composition of liquor. A quantitative relation between the rate of delignification and the concentration of free sulphur dioxide, or better, the partial pressure of sulphur dioxide gas, has been established. The nature and significance of this relation is discussed in connection with the mechanism of the delignification process. It has been shown that the hydrogen ion concentration alone does not determine the rate of cooking, but evidence is presented that indicates that the product of the concentrations of the hydrogen and bisulphite ions is the controlling factor.The yield of pulp for any given lignin content is independent of the free sulphur dioxide over the whole concentration range, but increases in a marked manner with the concentration of the combined. An explanation is offered, and the practical aspects are pointed out.

1938 ◽  
Vol 16b (7) ◽  
pp. 242-252
Author(s):  
J. M. Calhoun ◽  
J. J. R. Cannon ◽  
F. H. Yorston ◽  
O. Maass

The rate of delignification of resin extracted spruce wood-meal in magnesium base sulphite liquor has been determined at 130 °C. over the concentration range 0.5 to 4% combined, and 2 to 10% free, sulphur dioxide. The rate of reaction is roughly proportional to the concentration of free sulphur dioxide when the combined is constant, but decreases with increase in the concentration of combined when the free is constant. The relation of the rate of delignification to the liquor composition cannot be expressed by any simple equation of the type:[Formula: see text]where K and n are constants. The rate of cooking is somewhat greater in magnesium base sulphite liquor than in calcium base liquor of the same mole percentage composition.The yield of pulp at any given lignin content is independent of the free sulphur dioxide over the whole concentration range, but increases with increase in the concentration of the combined to a maximum at about 3%, and decreases at slightly higher concentrations. When the concentration of combined sulphur dioxide is greater than 1% the yield of pulp obtained from magnesium base cooks is slightly higher than that from corresponding calcium base cooks.


1930 ◽  
Vol 2 (1) ◽  
pp. 42-64 ◽  
Author(s):  
W. Boyd Campbell ◽  
O. Maass

The investigation described deals with the equilibria existing in a water solution of sulphur dioxide. The vapor pressures and conductivities of solutions of sulphur dioxide were measured over the temperature range 23° to 135 °C. at various concentrations up to 8%. The densities of the aqueous solutions up to 15% were also measured. A discussion of the various equilibria in the light of these data leads to the conclusion that sulphurous acid is one of considerable strength, its apparent weakness being due to the small amount of H2SO3 actually present. With rise in temperature the free sulphur dioxide increases and the hydrogen-ion concentration of the sulphite liquor used in current practice is so low that it seems highly improbable that the cooking reaction is due essentially to this factor. Apart from the bearing this work may have on the theory of sulphite cooking and the theory of the equilibria existing in the SO2−H2O system, it fills a considerable gap in the data regarding sulphur dioxide.


1934 ◽  
Vol 10 (1) ◽  
pp. 24-35 ◽  
Author(s):  
H. H. Saunderson ◽  
O. Maass

The penetration of aqueous sulphite solutions into differently shaped blocks of spruce wood has been investigated, the effect of the shape and type of wood, and of the presence of imprisoned air being determined. Measurements of the rates of diffusion of the constituents of calcium bisulphite solutions into pre-soaked blocks of wood showed that "free" sulphur dioxide diffused more readily than calcium bisulphite. Adsorption of sulphur dioxide and calcium bisulphite solutions by spruce wood was measured at 30° and 50 °C., and the influence of this factor on penetration was determined. The effect of penetration on delignification indicated the necessity of a satisfactory distribution of the lime salt at a low temperature to avoid localization of the lime during the pulping process.


2021 ◽  
Author(s):  
◽  
Peter Osvath

<p>The preparation of a range of fully saturated, unsubstituted pentaazamacrocycles is described. The macrocycles vary in ring size from fifteen to twenty members, and comprise every possible arrangement of dimethylene and trimethylene linkages between five nitroqens in a monocyclic arrangement. A new linear homologue of tetraethylene pentamine with trimethylene linkages between nitrogens is also reported. The copper(II) and nickel(II) complexes of these amines have been prepared; the conductivity and spectral properties have been determined in order to investigate their stereochemistry. The nickel(II) complexes of the two largest macrocycles appear to be five-coordinate both in the solid state and in solution. The remainder of the complexes are either five-coordinate (as the perchlorate salts in the solid state or in non-coordinating solvents) or six-coordinate (with a coordinated nitrate). Cobalt(III) complexes of the fifteen to eighteen membered macrocycles have been prepared with a variety of ligands occupying the sixth coordination site. Ligand field parameters have been derived from the electronic spectra of the complexes. The stereochemistry of the complexes and their behaviour on ligand substitution have been investigated principally by 13C n.m.r. Only a few of the numerous possible isomers of each species were formed. The structures of [Co(1, 4, 7, 10, 14-pentaazacycloheptadecane) Cl]Br0.33 Cl1.67. H2O and [Co(1, 4, 7, 11, 15-pentaazacyclooctadecane)Br]Br2, which were determined by single-crystal x-ray diffraction studies, are described. The spontaneous aquation rates of the bromo complexes have been investigated semi-quantitatively, and found to span many orders of magnitude. The most labile bromo complex [Co(1, 4, 8, 11, 15-pentaazacyclooctadecane)Br]Br2 spontaneously aquates in a matter of seconds at room temperature. The increasing strain and steric crowding caused by successive replacement of five-membered chelate rings by six-membered chelate rings, or by simply altering the sequence of five- and six-membered chelate rings is manifested in a progressive increase in the instability of the complexes. In the case of the nineteen- and twenty-membered macrocycles, this crowding and strain results in the formation of stable five-coordinate cobalt(II) complexes; for these ligands, no stable complexes were formed with the smaller cobalt(III) cation. The acid-dissociation kinetics of the copper(II) complexes have been examined in nitric acid at 298 K. A variable temperature study has also been performed on the complex of l, 4, 7, 10, 14-pentaazacycloheptadecane in order to determine the activation parameters. The complexes are labile by comparison with most tetraazamacrocyclic complexes. The dissociation reactions are first-order in complex concentration, but the acid-dependence varies. The observed rate constant is second-order in hydrogen ion concentration for the complex of 1, 4, 7, 10, 13-pentaazacyclopentadecane, first-order in hydrogen ion concentration for 1, 4, 7, 10, 14-pentaazacycloheptadecane and takes the form kobs = a[H+]2/(l+b[H+]2) for the complex of 1, 4, 7, 10, 13-pentaazacyclohexadecane. For the remainder of the complexes, the observed rate constant takes the form kobs = (c[H+] + d[H+]2)/(e + [H+]). Possible mechanisms that are consistent with the above behaviour are presented.</p>


1961 ◽  
Vol 39 (2) ◽  
pp. 265-272 ◽  
Author(s):  
Gérard E. Pelletier ◽  
Ludovic Ouellet

The inactivation of myosin adenosine triphosphatase activity was studied in 0.6 M potassium chloride solution at pH ranging from 7.0 to 10.8 and for 5 °C to 40 °C. The inactivation is a first-order process with respect to time and 0.6th order with respect to the concentration of protein. The rate of inactivation is independent of the pH for pH 7.0 to pH 8.5 at 35 °C and increases rapidly with pH at higher pH. At 12 °C, close to pH 10.4, the rate is inversely proportional to the 4.5th power of the hydrogen ion concentration. The energies of activation are 56 kcal mole−1 at pH 8.0 and 58 kcal mole−1 at pH 10.5. A discussion of the data stresses the importance of structural changes and indicates a possible role for the electrostatic charge in the inactivation process.


2021 ◽  
Author(s):  
C.R. Osunkwo ◽  
I.U. Nkole

Abstract The reduction of tris(2,2-bipyridine)cobalt(III) complex by thiosulphate ion in an aqueous acidic medium gave a notable outcome. The stoichiometric evaluation indicates that one mole of the reducing agent has been consumed by one mole of the oxidant, and the reaction complies with an overall equation: 2[Co(bpy)3]3+ + 2S2O32− 2[Co(bpy)3]2+ + S4O62− The kinetics study conducted under a pseudo-first-order method shows that the rate of the reaction was acid-reliant and third-order overall; zero-order in the [oxidant], second-order in the [reductant], and first-order in the hydrogen ion concentration. The empirical rate expression complies with the equation:− [Co(bpy)33+] = a [H+][S2O32−]2‘a’ = 77.82 dm6 mol−2 s−1; at [H+] = 2.0 × 10−2 mol dm−3, µ = 0.4 mol dm−3 (NaCl), T = 28 ± 1˚C and λmax = 560 nm.With increased ionic strength and decreased medium dielectric constant, the reaction rate increased. The inclusion of cations and anions accelerate and constricted the reaction rates respectively. Spectroscopic examination and kinetic evidence indicate an outer sphere mechanism, and the mechanism was therefore proposed via an outer-sphere route.


1963 ◽  
Vol 16 (3) ◽  
pp. 411 ◽  
Author(s):  
D Ilse ◽  
P Edman

In an attempt to extend the application of the phenylisothiocyanate degradation of peptides it was found necessary to study the kinetics of the conversion of phenylthiocarbamyl amino acids into phenylthiohydantoins. The conversion was found to obey first-order kinetics and to be catalyzed by hydrogen ions. A set of conditions with regard to time, hydrogen ion concentration and temperature was found, which allowed the quantitative or near quantitative conversion of all phenylthiocarbamyl amino acids into phenylthiohydantoins with the only exception of the phenylthiohydantoin of serine, which was returned in a yield of 20%.


1933 ◽  
Vol 8 (5) ◽  
pp. 415-428 ◽  
Author(s):  
H. Saunderson ◽  
H. W. Johnston ◽  
O. Maass

This paper deals with some of the factors which influence the penetration of sulphite liquor into wood during the cooking process. The experimental technique for this purpose is described. The particular factors investigated in this paper are the influence of the calcium sulphite precipitate and the composition of the liquor on penetration.Certain conclusions may be drawn from the experimental results presented. These are summarized as follows:(1) The rate of penetration of sulphite liquor through a block of spruce wood is constant for a fixed low temperature. At a constant high temperature the rate of penetration increases continuously during the duration of a run, due to the opening up of the wood. This "cooking" action becomes evident at about 90 °C. for heartwood, and below 70 °C. for sapwood.(2) The rate of penetration of sulphite liquor is greater for a higher concentration of free sulphur dioxide. This increase in rate with sulphur dioxide concentration becomes more noticeable at higher temperatures, indicating that at least a part of the effect is due to cooking action.(3) The formation of a precipitate of calcium sulphite on the wood at high temperatures decreases the rate of forced penetration. This effect is more noticeable with porous wood, where the pressure differential is small. The plugging action is largely a surface effect, due to the formation of a layer of precipitate over the ends of the tracheids of the wood.


1992 ◽  
Vol 57 (2) ◽  
pp. 326-331 ◽  
Author(s):  
Refat M. Hassan

The kinetics of hexachloroiridate(IV) oxidation of tin(II) in aqueous perchlorate media at a constant ionic strength of 2.0 mol dm-3 have been studied spectrophotometrically. The reaction was found to follow second-order overall kinetics and first order with respect to each of the reactants. The results showed hydrogen ion dependence where the reaction rate increased with increasing hydrogen ion concentration. The activation parameters were evaluated and a tentative reaction mechanism has been discussed.


2021 ◽  
Author(s):  
◽  
Peter Osvath

<p>The preparation of a range of fully saturated, unsubstituted pentaazamacrocycles is described. The macrocycles vary in ring size from fifteen to twenty members, and comprise every possible arrangement of dimethylene and trimethylene linkages between five nitroqens in a monocyclic arrangement. A new linear homologue of tetraethylene pentamine with trimethylene linkages between nitrogens is also reported. The copper(II) and nickel(II) complexes of these amines have been prepared; the conductivity and spectral properties have been determined in order to investigate their stereochemistry. The nickel(II) complexes of the two largest macrocycles appear to be five-coordinate both in the solid state and in solution. The remainder of the complexes are either five-coordinate (as the perchlorate salts in the solid state or in non-coordinating solvents) or six-coordinate (with a coordinated nitrate). Cobalt(III) complexes of the fifteen to eighteen membered macrocycles have been prepared with a variety of ligands occupying the sixth coordination site. Ligand field parameters have been derived from the electronic spectra of the complexes. The stereochemistry of the complexes and their behaviour on ligand substitution have been investigated principally by 13C n.m.r. Only a few of the numerous possible isomers of each species were formed. The structures of [Co(1, 4, 7, 10, 14-pentaazacycloheptadecane) Cl]Br0.33 Cl1.67. H2O and [Co(1, 4, 7, 11, 15-pentaazacyclooctadecane)Br]Br2, which were determined by single-crystal x-ray diffraction studies, are described. The spontaneous aquation rates of the bromo complexes have been investigated semi-quantitatively, and found to span many orders of magnitude. The most labile bromo complex [Co(1, 4, 8, 11, 15-pentaazacyclooctadecane)Br]Br2 spontaneously aquates in a matter of seconds at room temperature. The increasing strain and steric crowding caused by successive replacement of five-membered chelate rings by six-membered chelate rings, or by simply altering the sequence of five- and six-membered chelate rings is manifested in a progressive increase in the instability of the complexes. In the case of the nineteen- and twenty-membered macrocycles, this crowding and strain results in the formation of stable five-coordinate cobalt(II) complexes; for these ligands, no stable complexes were formed with the smaller cobalt(III) cation. The acid-dissociation kinetics of the copper(II) complexes have been examined in nitric acid at 298 K. A variable temperature study has also been performed on the complex of l, 4, 7, 10, 14-pentaazacycloheptadecane in order to determine the activation parameters. The complexes are labile by comparison with most tetraazamacrocyclic complexes. The dissociation reactions are first-order in complex concentration, but the acid-dependence varies. The observed rate constant is second-order in hydrogen ion concentration for the complex of 1, 4, 7, 10, 13-pentaazacyclopentadecane, first-order in hydrogen ion concentration for 1, 4, 7, 10, 14-pentaazacycloheptadecane and takes the form kobs = a[H+]2/(l+b[H+]2) for the complex of 1, 4, 7, 10, 13-pentaazacyclohexadecane. For the remainder of the complexes, the observed rate constant takes the form kobs = (c[H+] + d[H+]2)/(e + [H+]). Possible mechanisms that are consistent with the above behaviour are presented.</p>


Sign in / Sign up

Export Citation Format

Share Document