Constructing PbS quantum dot sensitized ZnO nanorod array photoelectrodes for highly efficient photovoltaic devices

2016 ◽  
Vol 94 (7) ◽  
pp. 687-692
Author(s):  
Masood Mehrabian ◽  
Naser Ghasemian
Keyword(s):  
Quantum Dot ◽  
Short Circuit ◽  
Zno Nanorods ◽  
Growth Period ◽  
Short Circuit Current ◽  
Nanorod Array ◽  
Open Circuit ◽  
Zno Film ◽  
Photovoltaic Properties ◽  
Pbs Quantum Dot

Solar cells with ZnO film/ZnO nanorods (NRs)/PbS quantum dot (QD) photoelectrodes were constructed and various properties were studied. The ZnO NRs were grown for different periods varying from 0 (ZnO film) to 30 min (ZnO NR30) and the effect of growth period on the photovoltaic properties was investigated. The cell with ZnO film/PbS QD as photoelectrode showed the open circuit voltage VOC of 0.59 V, short circuit current density JSC of 10.06 mAcm−2, and the power conversion efficiency of 3.29% under one sun illumination (air mass 1.5 global illumination at 100 mWcm−2). In a device containing of ZnO film/ZnO NR10/PbS QD (as photoelectrode), mentioned photovoltaic parameters increased to 0.61 V, 10.47 mAcm−2 and 3.81%, respectively.

Fabrication of Photovoltaic Devices Using ZnO Nanostructures and SnS Thin Films

NANO ◽  
2016 ◽  
Vol 11 (07) ◽  
pp. 1650077 ◽  
Author(s):  
N. Koteeswara Reddy ◽  
M. Devika ◽  
K. R. Gunasekhar ◽  
E. S. R. Gopal
Keyword(s):  
Thin Films ◽  
Solar Cell ◽  
Short Circuit ◽  
Zno Nanorods ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Zno Nanostructures ◽  
Photovoltaic Properties ◽  
Thermal Evaporation Method ◽  
Sns Thin Films

The development of nontoxic and cost-effective solar cell devices is one of the challenging tasks even now. With this objective, solar cell devices using tin mono sulfide (SnS) thin films and zinc oxide (ZnO) nanostructures with a superstrate configuration of ITO/ZnO film/ZnO nanorods/SnS film/Zn have been fabricated and their photovoltaic properties have been investigated. Vertically aligned ZnO nanostructures were grown on indium doped tin oxide substrate by chemical solution method and then, SnS thin films were deposited by thermal evaporation method. A typical solar cell device exhibited significant light conversion efficiency with an open circuit voltage and short circuit current of 350[Formula: see text]mV and 5.14[Formula: see text]mA, respectively.

A green synthesis of CISe nanocrystal ink and preparation of quantum dot sensitized solar cells

2020 ◽  
Vol 13 (06) ◽  
pp. 2050028
Author(s):  
Tianyu Guo ◽  
Hui Zhang ◽  
Guifeng Chen ◽  
Boling Long ◽  
Luxiao Xie ◽  
...  
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Quantum Confinement Effect ◽  
Zno Nanorods ◽  
Triethylene Glycol ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Sensitized Solar Cells

I–III–VI chalcopyrite copper indium selenium is one of therepresentatives of the light absorbing layer material, and is often used for a thin-film solar cell. With the development of nano-technology, CuInSe2 quantum dots (CISe QDs) which have intermediate belt and excitation effect characteristics are applied to the solar cells as an alternative of Cd- or S-based QDs. Most conventional methods for the synthesis of CISe QDs using solution involve the dangerous and environmentally unfriendly Oleylamine or phosphine coordination compounds. In this work, CISe QDs were synthesized by a green, safe and low-temperature method in triethylene glycol. Through controlling the growth temperature and time, the diameter can be adjusted from 3[Formula: see text]nm to 10[Formula: see text]nm. The samples exhibit quantum confinement effect, and have a controllable optical band gap. QDs were deposited on the surface of ZnO nanorods to obtain a photoanode, which were fabricated into quantum dot-sensitized solar cells. The device exhibits size-dependent performance. And the open circuit voltage shows a fluctuation up to 0.26[Formula: see text]V. When the size is 4[Formula: see text]nm, the short circuit current density is the largest (15[Formula: see text]mA/cm2).

scholarly journals Direct AFM-based nanoscale mapping and tomography of open-circuit voltages for photovoltaics

2018 ◽  
Vol 9 ◽  
pp. 1802-1808 ◽  
Author(s):  
Katherine Atamanuk ◽  
Justin Luria ◽  
Bryan D Huey
Keyword(s):  
Solar Cells ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Three Dimensional ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Order Of Magnitude ◽  
Individual Grains

The nanoscale optoelectronic properties of materials can be especially important for polycrystalline photovoltaics including many sensor and solar cell designs. For thin film solar cells such as CdTe, the open-circuit voltage and short-circuit current are especially critical performance indicators, often varying between and even within individual grains. A new method for directly mapping the open-circuit voltage leverages photo-conducting AFM, along with an additional proportional-integral-derivative feedback loop configured to maintain open-circuit conditions while scanning. Alternating with short-circuit current mapping efficiently provides complementary insight into the highly microstructurally sensitive local and ensemble photovoltaic performance. Furthermore, direct open-circuit voltage mapping is compatible with tomographic AFM, which additionally leverages gradual nanoscale milling by the AFM probe essentially for serial sectioning. The two-dimensional and three-dimensional results for CdTe solar cells during in situ illumination reveal local to mesoscale contributions to PV performance based on the order of magnitude variations in photovoltaic properties with distinct grains, at grain boundaries, and for sub-granular planar defects.

scholarly journals Effects of Different Doping Ratio of Cu Doped CdS on QDSCs Performance

2015 ◽  
Vol 2015 ◽  
pp. 1-4
Author(s):  
Xiaojun Zhu ◽  
Xiaoping Zou ◽  
Hongquan Zhou
Keyword(s):  
Solar Cells ◽  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Photoelectric Conversion Efficiency ◽  
Photoelectric Conversion ◽  
Sensitized Solar Cells ◽  
Doping Ratio

We use the successive ionic layer adsorption and reaction (SILAR) method for the preparation of quantum dot sensitized solar cells, to improve the performance of solar cells by doping quantum dots. We tested the UV-Vis absorption spectrum of undoped CdS QDSCs and Cu doped CdS QDSCs with different doping ratios. The doping ratios of copper were 1 : 100, 1 : 500, and 1 : 1000, respectively. The experimental results show that, under the same SILAR cycle number, Cu doped CdS quantum dot sensitized solar cells have higher open circuit voltage, short circuit current density photoelectric conversion efficiency than undoped CdS quantum dots sensitized solar cells. Refinement of Cu doping ratio are 1 : 10, 1 : 100, 1 : 200, 1 : 500, and 1 : 1000. When the proportion of Cu and CdS is 1 : 10, all the parameters of the QDSCs reach the minimum value, and, with the decrease of the proportion, the short circuit current density, open circuit voltage, and the photoelectric conversion efficiency are all increased. When proportion is 1 : 500, all parameters reach the maximum values. While with further reduction of the doping ratio of Cu, the parameters of QDSCs have a decline tendency. The results showed that, in a certain range, the lower the doping ratio of Cu, the better the performance of quantum dot sensitized solar cell.

Photovoltaic properties of silicon nanocrystals in silicon nitride prepared by ammonia sputtering

2015 ◽  
Vol 08 (05) ◽  
pp. 1550052
Author(s):  
Xiaobo Chen
Keyword(s):  
Silicon Nitride ◽  
Flow Rate ◽  
Photoelectron Spectroscopy ◽  
Silicon Nanocrystals ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
X Ray ◽  
Xps Characterization

In this work, we present an investigation of the photovoltaic properties of low-temperature (700°C annealing temperature) prepared P -doped Silicon nanocrystals ( Si   NCs ) in silicon nitride by ammonia sputtering followed by rapid thermal annealing (RTA). We examined how the flow rate of NH3influenced the structural properties of the annealed films by using Raman scattering, grazing incidence X-ray diffraction (GI XRD) and transmission electron microscopy (TEM), it was found that the appropriate flow rate of NH3is 3 sccm. For the sample deposited at the flow rate of 3 sccm, TEM image showed that Si   NCs were formed with a mean size about 3.7 nm and the density of ~ 2.1 × 1012cm-2; X-ray photoelectron spectroscopy (XPS) characterization showed the existence of Si – P bonds, indicating effective P doping; the average absorptance of higher than 65% and a significant amount of photocurrent makes it suitable for photoactive. Moreover, the experimental P -doped Si   NCs : Si3N4/ p - Si heterojunction solar cell has been fabricated, and the device performance was studied. The photovoltaic device fabricated exhibits an open-circuit voltage (VOC) and a short-circuit current density (JSC) of 470 mV and 3.25 mA/cm2, respectively.

Novel Linear and Hyperbranched Polythiophene Derivatives Containing Diketopyrrolopyrroles as Linking Groups

2015 ◽  
Vol 1771 ◽  
pp. 213-219
Author(s):  
Sheng-Hsiung Yang ◽  
Chia-Hao Hsieh
Keyword(s):  
Fill Factor ◽  
Open Circuit Voltage ◽  
Short Circuit ◽  
Power Conversion ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Molecular Weights ◽  
Active Layers ◽  
Film State

ABSTRACTThe goal of this research is to synthesize novel linear and hyperbranched polythiophene derivatives containing diketopyrrolopyrrole (DPP) as linking groups, and to investigate thermal, optical, electrochemical, and photovoltaic properties of those derivatives. Polymers with high regioregularity were synthesized via the Universal Grignard metathesis polymerization. Those linear or hyperbranched polythiophenes containing DPP bridging moieties showed higher molecular weights and better thermal stability compared with normal P3HT. The UV-vis absorption spectra of the DPP-containing polymers are similar to that of P3HT in film state, while they show distinct attenuation in fluorescent emission. Finally, all polymers were blended with PC61BM and used as active layers for fabrication of inverted solar devices. The devices based on those DPP-containing polythiophenes revealed the open-circuit voltage (VOC) of 0.55–0.58 V, the short-circuit current (JSC) of 8.62–16.21 mA/cm2, the fill factor (FF) of 36–41%, and the power conversion efficiency (PCE) of 1.73–3.74%.

scholarly journals Synthesis of Cyano-Substituted Conjugated Polymers for Photovoltaic Applications

Polymers ◽  
2019 ◽  
Vol 11 (5) ◽  
pp. 746 ◽  
Author(s):  
Mun Ho Yang ◽  
Ho Cheol Jin ◽  
Joo Hyun Kim ◽  
Dong Wook Chang
Keyword(s):  
Conjugated Polymers ◽  
Molecular Orbital ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Energy Levels ◽  
Coupling Reaction ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Strong Electron ◽  
Photovoltaic Properties

Three conjugated polymers, in which the electron-donating (D) 5-alkylthiophene-2-yl-substitued benzodithiophene was linked to three different electron-accepting (A) moieties, i.e., benzothiadiazole (BT), diphenylquinoxaline (DPQ), and dibenzophenazine (DBP) derivative via thiophene bridge, were synthesized using the Stille coupling reaction. In particular, the strong electron-withdrawing cyano (CN) group was incorporated into the A units BT, DPQ, and DBP to afford three D–A type target polymers PB–BTCN, PB–DPQCN, and PB–DBPCN, respectively. Owing to the significant contribution of the CN-substituent, these polymers exhibit not only low-lying energy levels of both the highest occupied molecular orbital and the lowest unoccupied molecular orbital, but also reduced bandgaps. Furthermore, to investigate the photovoltaic properties of polymers, inverted-type devices with the structure of ITO/ZnO/Polymer:PC71BM/MoO3/Ag were fabricated and analyzed. All the polymer solar cells based on the three cyano-substituted conjugated polymers showed high open-circuit voltages (Voc) greater than 0.89 V, and the highest power conversion efficiency of 4.59% was obtained from the device based on PB-BtCN with a Voc of 0.93 V, short-circuit current of 7.36 mA cm−2, and fill factor of 67.1%.

scholarly journals Steady Enhancement in Photovoltaic Properties of Fluorine Functionalized Quinoxaline-Based Narrow Bandgap Polymer

Molecules ◽  
2018 ◽  
Vol 24 (1) ◽  
pp. 54 ◽  
Author(s):  
Zhonglian Wu ◽  
Huanxiang Jiang ◽  
Xingzhu Wang ◽  
Lei Yan ◽  
Wei Zeng ◽  
...  
Keyword(s):  
Fill Factor ◽  
Polymer Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Hole Mobility ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Promising Candidate ◽  
Photovoltaic Properties ◽  
Narrow Bandgap

To investigate the influence of fluoride phenyl side-chains onto a quinoxaline (Qx) unit on the photovoltaic performance of the narrow bandgap (NBG) photovoltaic polymers, herein, two novel NBG copolymers, PBDTT-DTQx and PBDTT-DTmFQx, were synthesized and characterized. 2-ethylhexylthiothiophene-substituted benzodithiophene (BDTT), 2,3-diphenylquinoxaline (DQx) [or 2,3-bis(3-fluorophenyl)quinoxaline (DmFQx)] and 2-ethylhexylthiophene (T) were used as the electron donor (D) unit, electron-withdrawing acceptor (A) unit and π-bridge, respectively. Compared to non-fluorine substituted PBDTT-DTQx, fluoride PBDTT-DTmFQx exhibited a wide UV-Vis absorption spectrum and high hole mobility. An enhanced short-circuit current (Jsc) and fill factor (FF) simultaneously gave rise to favorable efficiencies in the polymer/PC71BM-based polymer solar cells (PSCs). Under the illumination of AM 1.5G (100 mW cm−2), a maximum power conversion efficiency (PCE) of 6.40% was achieved with an open-circuit voltage (Voc) of 0.87 V, a Jsc of 12.0 mA cm−2 and a FF of 61.45% in PBDTT-DTmFQx/PC71BM-based PSCs, while PBDTT-DTQx-based devices also exhibited a PCE of 5.43%. The excellent results obtained demonstrate that PBDTT-DTmFQx by fluorine atom engineering could be a promising candidate for organic photovoltaics.

scholarly journals Doped Heterojunction Used in Quantum Dot Sensitized Solar Cell

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
Yanyan Gao ◽  
Xiaoping Zou ◽  
Zongbo Huang
Keyword(s):  
Quantum Dot ◽  
Short Circuit ◽  
Short Circuit Current ◽  
Short Circuit Current Density ◽  
Open Circuit ◽  
Silar Method ◽  
Foreign Atom ◽  
Layer Adsorption ◽  
Lattice Distortions ◽  
Sensitized Solar Cells

Incorporated foreign atoms into the quantum dots (QDs) used in heterojunction have always been a challenge for solar energy conversion. A foreign atom indium atom was incorporated into PbS/CdS QDs to prepare In-PbS/In-CdS heterojunction by successive ionic layer adsorption and reaction method which is a chemical method. Experimental results indicate that PbS or CdS has been doped with In by SILAR method; the concentration of PbS and CdS which was doped In atoms has no significantly increase or decrease. In addition, incorporating of Indium atoms has resulted in the lattice distortions or changes of PbS or CdS and improved the light harvest of heterojunction. Using this heterojunction, Pt counter electrode and polysulfide electrolyte, to fabricate quantum dot sensitized solar cells, the short circuit current density ballooned to 27.01 mA/cm2from 13.61 mA/cm2and the open circuit voltage was improved to 0.43 V from 0.37 V at the same time.

scholarly journals Performance of Natural Dye Extracted from Annatto, Black Plum, Turmeric, Red Spinach, and Cactus as Photosensitizers in TiO2NP/TiNT Composites for Solar Cell Applications

2021 ◽  
Vol 2021 ◽  
pp. 1-12
Author(s):  
Shibu Joseph ◽  
Albin John P. Paul Winston ◽  
S. Muthupandi ◽  
P. Shobha ◽  
S. Mary Margaret ◽  
...  
Keyword(s):  
Solar Cell ◽  
Low Cost ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Photovoltaic Properties ◽  
Ft Ir ◽  
Conversion Efficiencies ◽  
Sensitized Solar Cells

This paper is aimed at how to select, extract, and characterize natural dyes and to use them as sensitizers in dye-sensitized solar cells (DSSCs). Dyes obtained from fresh sources of annatto fruits, black plums, cactus fruits, turmeric roots, and red spinach leaves were used as sensitizers. The dye pigments were analyzed using UV-Vis spectrophotometer and FT-IR for the characterization of their spectral properties. The combination from Titanium dioxide paste with the powdered nanotubes was used as photoanodes for DSSCs. The photovoltaic properties of the DSSCs such as efficiency, fill factor, open-circuit voltage, and short circuit current were studied using a standard illumination of air-mass 1.5 global (AM 1.5 G) having an irradiance of 100 mW/cm2. The highest power conversion efficiencies (η) of 0.7% was achieved for the DSSCs fabricated using dye extracted from annatto fruits and 0.4% each for dyes extracted from black plum fruits and cactus fruits, respectively. The widespread accessibility of these fruits, roots, and leaves and ease of extraction of dyes from these ordinarily available natural resources render them unique and low-cost candidates for solar cell fabrication.

Sign in / Sign up

Export Citation Format

Share Document