Magnetohydrodynamic (MHD) mixed convection stagnation point flow of a nanofluid over a vertical plate with viscous dissipation

2015 ◽  
Vol 93 (11) ◽  
pp. 1365-1374 ◽  
Author(s):  
Irfan Mustafa ◽  
Tariq Javed ◽  
Abid Majeed
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Mixed Convection ◽  
Skin Friction ◽  
Viscous Dissipation ◽  
Local Nusselt Number ◽  
Vertical Plate ◽  
Volume Fraction ◽  
Skin Friction Coefficient ◽  
Flow Case

In this study, magnetohydrodynamic effects on the mixed convection flow of nanofluid particles, namely, Cu (copper) and Al2O3 (alumina) near a stagnation region over a vertical plate in the presence of viscous dissipation is investigated. The governing equations of the nanofluid flow model proposed by Tiwari and Das (Int. J. Heat Mass Transfer, 50, 2002 (2007). doi:10.1016/j.ijheatmasstransfer.2006.09.034) are converted into a dimensionless nonlinear system of ordinary differential equations by using the similarity transformation. The solution of the resulting equations is obtained numerically by using a very efficient implicit scheme known as the Keller box method. A comparison with previous studies is shown in tabular form and excellent agreement is found. The effects of pertinent parameters like magnetic parameter M, Eckert number Ec, and volume fraction parameter ϕ on velocity, temperature, skin friction coefficient, and local Nusselt number with fixed value of Prandtl number Pr = 6.2 are shown graphically and discussed. These results show that the skin friction coefficient increases for both nanoparticles in assisting and opposing flow cases because of increasing absolute values of M and Ec, on the other hand heat transfer rate is enhanced in the opposing flow case and reduced in the assisting flow case. The values of skin friction coefficient for both nanoparticles, namely, Cu and Al2O3 increase with the increase in volume fraction parameter ϕ in both assisting and opposing flow cases and Cu has a higher value than Al2O3. The same behavior is observed for local Nusselt number in opposing flow, but in assisting flow the value of local Nusselt number decreases with the increase of ϕ in the presence of magnetic and viscous dissipation effects and Cu has a smaller value than Al2O3.

Homotopy analysis method for unsteady mixed convective stagnation-point flow of a nanofluid using Tiwari-Das nanofluid model

2016 ◽  
Vol 26 (1) ◽  
pp. 40-62 ◽  
Author(s):  
Saeed Dinarvand ◽  
Reza Hosseini ◽  
Ioan Pop
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Mixed Convection ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Magnetic Parameter ◽  
Volume Fraction ◽  
Skin Friction Coefficient ◽  
Nanoparticle Volume Fraction ◽  
Content Type

Purpose – The current study is mainly motivated by the need to the development of the transient MHD mixed convection stagnation-point flow and heat transfer of an electrically conducting nanofluid over a vertical permeable stretching/shrinking sheet by means of Tiwari-Das nanofluid model. The purpose of this paper is to investigate the effects of the parameters governing the flow i.e. the nanoparticle volume fraction, the unsteadiness parameter, the magnetic parameter, the wall transpiration parameter, the mixed convection parameter and the velocity ratio parameter on dimensionless velocity and temperature distributions, skin friction coefficient and local Nusselt number. Design/methodology/approach – The mathematical model has been formulated based on Tiwari-Das nanofluid model. Three different types of water-based nanofluid with copper, aluminum oxide (alumina) and titanium dioxide (titania) as nanoparticles are considered in this investigation. Using appropriate similarity variables, the governing equations are transformed into nonlinear ordinary differential equations in the dimensionless stream function, which is solved analytically by the well-know homotopy analysis method. The present simulations agree closely with the previous studies in the especial cases. Findings – The results show that by increasing the nanoparticle volume fraction, the unsteadiness parameter, the magnetic parameter, the wall transpiration parameter, the mixed convection parameter or reducing the velocity ratio parameter, the skin friction coefficient enhances. Furthermore, the local Nusselt number enhances with different rates by increasing the nanoparticle volume fraction, the unsteadiness parameter, the magnetic parameter, the wall transpiration parameter, the mixed convection parameter and the velocity ratio parameter. Besides, the skin friction coefficient and the local Nusselt number are highest for copper-water nanofluid compared to the alumina-water and titania-water nanofluids. Originality/value – Tiwari-Das nanofluid model has not been applied for the flow with these characteristics as mentioned in the paper. A comprehensive survey on boundary layer behavior has been presented. There are few studies regarding as analysis on thermal and hydrodynamics boundary layer. All plots presented in the paper are new and did not report in any other study. The effects of the parameters governing the flow on skin friction coefficient and local Nusselt number have been illustrated in the paper while there are some conflicts with previous published article that have been interpreted in details in the paper.

scholarly journals Effects of Slip and Heat Generation/Absorption on MHD Mixed Convection Flow of a Micropolar Fluid over a Heated Stretching Surface

2010 ◽  
Vol 2010 ◽  
pp. 1-20 ◽  
Author(s):  
Mostafa Mahmoud ◽  
Shimaa Waheed
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Mixed Convection ◽  
Skin Friction ◽  
Heat Generation ◽  
Local Nusselt Number ◽  
Skin Friction Coefficient ◽  
Convection Flow ◽  
Local Skin ◽  
Local Skin Friction

A theoretical analysis is performed to study the flow and heat transfer characteristics of magnetohydrodynamic mixed convection flow of a micropolar fluid past a stretching surface with slip velocity at the surface and heat generation (absorption). The transformed equations solved numerically using the Chebyshev spectral method. Numerical results for the velocity, the angular velocity, and the temperature for various values of different parameters are illustrated graphically. Also, the effects of various parameters on the local skin-friction coefficient and the local Nusselt number are given in tabular form and discussed. The results show that the mixed convection parameter has the effect of enhancing both the velocity and the local Nusselt number and suppressing both the local skin-friction coefficient and the temperature. It is found that local skin-friction coefficient increases while the local Nusselt number decreases as the magnetic parameter increases. The results show also that increasing the heat generation parameter leads to a rise in both the velocity and the temperature and a fall in the local skin-friction coefficient and the local Nusselt number. Furthermore, it is shown that the local skin-friction coefficient and the local Nusselt number decrease when the slip parameter increases.

Nanofluid flow past an impulsively started vertical plate with variable surface temperature

2016 ◽  
Vol 26 (1) ◽  
pp. 328-347 ◽  
Author(s):  
Rajesh Vemula ◽  
A J Chamkha ◽  
Mallesh M. P.
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Vertical Plate ◽  
Aluminium Oxide ◽  
Skin Friction Coefficient ◽  
Viscous Drag ◽  
Content Type ◽  
Variable Surface ◽  
Variable Surface Temperature

Purpose – The purpose of this paper is to focus on the numerical modelling of transient natural convection flow of an incompressible viscous nanofluid past an impulsively started semi-infinite vertical plate with variable surface temperature. Design/methodology/approach – The problem is governed by the coupled non-linear partial differential equations with appropriate boundary conditions. A robust, well-tested, Crank-Nicolson type of implicit finite-difference method, which is unconditionally stable and convergent, is used to solve the governing non-linear set of partial differential equations. Findings – The local and average values of the skin-friction coefficient (viscous drag) and the average Nusselt number (the rate of heat transfer) decreased, while the local Nusselt number increased for all nanofluids, namely, aluminium oxide-water, copper-water, titanium oxide-water and silver-water with an increase in the temperature exponent m. Selecting aluminium oxide as the dispersing nanoparticles leads to the maximum average Nusselt number (the rate of heat transfer), while choosing silver as the dispersing nanoparticles leads to the minimum local Nusselt number compared to the other nanofluids for all values of the temperature exponent m. Also, choosing silver as the dispersing nanoparticles leads to the minimum skin-friction coefficient (viscous drag), while selecting aluminium oxide as the dispersing nanoparticles leads to the maximum skin-friction coefficient (viscous drag) for all values of the temperature exponent m. Research limitations/implications – The Brinkman model for dynamic viscosity and Maxwell-Garnett model for thermal conductivity are employed. The governing boundary layer equations are written according to The Tiwari-Das nanofluid model. A range of nanofluids containing nanoparticles of aluminium oxide, copper, titanium oxide and silver with nanoparticle volume fraction range less than or equal to 0.04 are considered. Practical implications – The present simulations are relevant to nanomaterials thermal flow processing in the chemical engineering and metallurgy industries. This study also provides an important benchmark for further simulations of nanofluid dynamic transport phenomena of relevance to materials processing, with alternative computational algorithms (e.g. finite element methods). Originality/value – This paper is relatively original and illustrates the influence of variable surface temperature on transient natural convection flow of a viscous incompressible nanofluid and heat transfer from an impulsively started semi-infinite vertical plate.

Hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface

2019 ◽  
Vol 29 (9) ◽  
pp. 3110-3127 ◽  
Author(s):  
Iskandar Waini ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Skin Friction Coefficient ◽  
Hybrid Nanofluid ◽  
Content Type ◽  
Flow And Heat Transfer ◽  
Shrinking Surface

PurposeThis paper aims to investigate the steady flow and heat transfer of a Cu-Al2O3/water hybrid nanofluid over a nonlinear permeable stretching/shrinking surface with radiation effects. The surface velocity condition is assumed to be of the power-law form with an exponent of 1/3. The governing equations of the problem are converted into a system of similarity equations by using a similarity transformation.Design/methodology/approachThe problem is solved numerically using the boundary value problem solver (bvp4c) in Matlab software. The results of the skin friction coefficient and the local Nusselt number as well as the velocity and temperature profiles are presented through graphs and tables for several values of the parameters. The effects of these parameters on the flow and heat transfer characteristics are examined and discussed.FindingsResults found that dual solutions exist for a certain range of the stretching/shrinking and suction parameters. The increment of the skin friction coefficient and reduction of the local Nusselt number on the shrinking sheet is observed with the increasing of copper (Cu) nanoparticle volume fractions for the upper branch. The skin friction coefficient and the local Nusselt number increase when suction parameter is increased for the upper branch. Meanwhile, the temperature increases in the presence of the radiation parameter for both branches.Originality/valueThe problem of Cu-Al2O3/water hybrid nanofluid flow and heat transfer over a nonlinear permeable stretching/shrinking surface with radiation effects is the important originality of the present study where the dual solutions for the flow reversals are obtained.

scholarly journals Three-Dimensional Flow and Heat Transfer Past a Permeable Exponentially Stretching/Shrinking Sheet in a Nanofluid

2014 ◽  
Vol 2014 ◽  
pp. 1-6 ◽  
Author(s):  
Syahira Mansur ◽  
Anuar Ishak ◽  
Ioan Pop
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Three Dimensional ◽  
Lewis Number ◽  
Skin Friction Coefficient ◽  
Shrinking Sheet ◽  
Three Dimensional Flow ◽  
Flow And Heat Transfer

The three-dimensional flow and heat transfer of a nanofluid over a stretching/shrinking sheet is investigated. Numerical results are obtained using bvp4c in MATLAB. The results show nonunique solutions for the shrinking case. The effects of the stretching/shrinking parameter, suction parameter, Brownian motion parameter, thermophoresis parameter, and Lewis number on the local skin friction coefficient and the local Nusselt number are studied. Suction increases the solution domain. Furthermore, as the sheet is shrunk in thex-direction, suction increases the skin friction coefficient in the same direction while decreasing the skin friction coefficient in they-direction. The local Nusselt number is consistently lower for higher values of thermophoresis parameter and Lewis number. On the other hand, the local Nusselt number increases as the Brownian motion parameter increases.

scholarly journals Micropolar ferrofluid flow via natural convective about a radiative isoflux sphere

2021 ◽  
Vol 13 (2) ◽  
pp. 168781402199439
Author(s):  
Saber EL-Kabeir ◽  
Ahmed Rashad ◽  
Waqar Khan ◽  
Zeinab Mahmoud Abdelrahman
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Thermal Radiation ◽  
Skin Friction ◽  
Magnetic Force ◽  
Volume Fraction ◽  
Skin Friction Coefficient ◽  
Temperature Fields ◽  
Partial Slip ◽  
Convection Flow

Current investigation scrutinizes the magnetohydrodynamic (MHD) natural convection flow of micropolar ferrofluid across an isoflux sphere with the impacts of thermal radiation and partial slip. Cobalt-nanoparticles with kerosene as the base fluid are considered. The governing partial differential conservation equations and convenient boundary conditions are rendered into a nondimensional form. The finite difference method (FDM) is then applied to determine the solution of a collection of resultant equations. The outcomes obtained by FDM have also compared with cited investigation. Illustrations describing influences of prominent parameters which provides physical interpretations of velocity, angular velocity, and temperature fields as well as the skin friction coefficient and Nusselt number are examined in detail with the help of graphical representations. This investigation determined that the skin-friction coefficient and heat transport rate reduced along with augmentation in the magnetic force and micropolar parameter, while opposite performance is adhered with elevating in the thermal radiation. Moreover, the boosted nanoparticle volume fraction reduced the skin friction coefficient and improved the Nusselt number.

Non-similar characteristics of mixed convective slip flow over a wedge with temperature-dependent thermo-physical properties

2019 ◽  
Vol 33 (36) ◽  
pp. 1950455
Author(s):  
Nepal Chandra Roy ◽  
Sudharonjon Roy ◽  
Naved Azum ◽  
Anish Khan ◽  
Abdullah M. Asiri ◽  
...  
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Sherwood Number ◽  
Local Nusselt Number ◽  
Slip Flow ◽  
Skin Friction Coefficient ◽  
Local Skin ◽  
Local Skin Friction ◽  
Local Sherwood Number

We examined heat and mass transfer characteristics of mixed convective slip flow over a wedge taking into account the effect of variable transport properties. Unlike other studies, we have utilized non-similar transformation to get the non-similar features of the mixed convective slip flow. For comparison, stream function formulation is used to reduce the governing equation into a convenient form for short- and long-time regimes. We have determined the series solutions by adopting the perturbation techniques. The agreement between the numerical and series solutions is found to be excellent. Numerical solutions reveal that the slip parameters augment the momentum, thermal and concentration boundary layers. The local skin friction coefficient, the local Nusselt number and the local Sherwood number are found to decrease for higher value of slip parameters. For the increasing value of the variable viscosity parameter, the velocity is stronger, but the temperature and concentration lessen. Contrary to this, this parameter diminishes the local skin friction coefficient, local Nusselt number and local Sherwood number. Due to the increase of mass diffusivity parameter, the velocity and concentration significantly increase whereas the temperature remains almost unaffected. Moreover, the mass diffusivity variation parameter leads to an increase in the local skin friction coefficient and local Nusselt number, but it reduces the local Sherwood number.

Passive control of nanoparticle of micropolar fluid past a stretching sheet with nanoparticles, convective boundary condition and second-order slip

2016 ◽  
Vol 231 (4) ◽  
pp. 704-719 ◽  
Author(s):  
Wubshet Ibrahim
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Local Nusselt Number ◽  
Micropolar Fluid ◽  
Passive Control ◽  
Stretching Sheet ◽  
Skin Friction Coefficient ◽  
Second Order ◽  
Non Linear

This article deals with a second-order slip flow and magnetic field on boundary layer flow of micropolar fluid past a stretching sheet. Situation of nil normal flux of nanoparticles at the wall for the stretching flow is taken into account. By employing appropriate similarity transformation and non-dimensional variables, the governing non-linear boundary-value problems were reduced into coupled higher order non-linear ordinary differential equation. Then, numerical solution for velocity, angular velocity (microrotation), temperature, and concentration has been established. The equations were numerically solved using the function bvp4c from the matlab software for different values of governing parameters. Numerical results have been obtained and discussed for non-dimensional velocity, temperature, microrotation, the skin friction coefficient, and local Nusselt number using some fixed values of the governing parameters. The results indicate that the skin friction coefficient Cf increases as the values of slip parameter γ increase. However, the local Nusselt number − [Formula: see text] increases as thermophoresis parameter Nt, microrotation parameter β, and convective parameter Bi increase. The wall couple stress coefficient decreases as the values of governing parameters such as magnetic parameter M, material parameter β, and for both slip parameters γ and δ increase. A comparison with earlier investigations available in the literature has been done and an excellent agreement is achieved.

scholarly journals Duality Solutions in Hydromagnetic Flow of SWCNT-MWCNT/Water Hybrid Nanofluid over Vertical Moving Slender Needle

Mathematics ◽  
2021 ◽  
Vol 9 (22) ◽  
pp. 2927
Author(s):  
Nur Adilah Liyana Aladdin ◽  
Norfifah Bachok
Keyword(s):  
Heat Transfer ◽  
Differential Equation ◽  
Carbon Nanotube ◽  
Friction Coefficient ◽  
Mixed Convection ◽  
Skin Friction ◽  
Volume Fraction ◽  
Skin Friction Coefficient ◽  
Convection Boundary Layer ◽  
Hybrid Nanofluid

Recently, the topic of convection of heat transfer has created an interest among researchers because of its numerous applications in the daily life. The objective of this paper was to study theoretically the problem of mixed convection boundary layer flow and heat transfer of single-wall carbon nanotube (SWCNT) and multi-wall carbon nanotube (MWCNT) in presence of hydromagnetic effects. The problem was initiated by formulating a mathematical model in partial differential equation (PDE) for the hybrid nanofluid flow with appropriate boundary conditions. The similarity equation was used to transform the PDE into an ordinary differential equation (ODE) and solved using bvp4c in MATLAB. The graphical results on variation of skin friction coefficient, , local Nusselt number, , shear stress, and local heat flux, with the effects of magnetic, size of needle, c, mixed convection parameter, and volume fraction of nanoparticles, were presented and discussed in detail. The study revealed that duality of solutions appears when the buoyance force is in opposing flow of the fluid motion, The presence of M in hybrid nanofluid reduced the skin friction coefficient and heat transfer. On the other hand, the and increased as different concentrations of and c were added. It gives an insight into the medical field, especially in treating cancer cells. By means, it reveals that CNTs hybrid nanofluid shows high potential in reaching the site of tumors faster compared with nanofluid. A stability analysis has to be carried out. It is noticed that the first solution was stable and physically realizable.

scholarly journals Unsteady Hydromagnetic Flow of Radiating Fluid Past a Convectively Heated Vertical Plate with the Navier Slip

2014 ◽  
Vol 2014 ◽  
pp. 1-10 ◽  
Author(s):  
O. D. Makinde ◽  
M. S. Tshehla
Keyword(s):  
Nusselt Number ◽  
Friction Coefficient ◽  
Skin Friction ◽  
Vertical Plate ◽  
Fluid Velocity ◽  
Nonlinear Partial Differential Equations ◽  
Skin Friction Coefficient ◽  
Newtonian Heating ◽  
Local Skin ◽  
Navier Slip

This paper investigates the unsteady hydromagnetic-free convection of an incompressible electrical conducting Boussinesq’s radiating fluid past a moving vertical plate in an optically thin environment with the Navier slip, viscous dissipation, and Ohmic and Newtonian heating. The nonlinear partial differential equations governing the transient problem are obtained and tackled numerically using a semidiscretization finite difference method coupled with Runge-Kutta Fehlberg integration technique. Numerical data for the local skin friction coefficient and the Nusselt number have been tabulated for various values of parametric conditions. Graphical results for the fluid velocity, temperature, skin friction, and the Nusselt number are presented and discussed. The results indicate that the skin friction coefficient decreases while the heat transfer rate at the plate surface increases as the slip parameter and Newtonian heating increase.

Sign in / Sign up

Export Citation Format

Share Document