Gas flooding of an inclined blade impeller

1991 ◽  
Vol 56 (3) ◽  
pp. 636-645 ◽  
Author(s):  
Václav Machoň ◽  
Ivan Fořt ◽  
Eva Antošová ◽  
Bohumil Španihel ◽  
Vladimír Kudrna
Keyword(s):  
Relative Size ◽  
Power Input ◽  
Vessel Diameter ◽  
Turbulent Regime ◽  
Gas Flooding ◽  
Rotating Impeller ◽  
Balance Of Forces ◽  
Phase Water ◽  
Input Ratio ◽  
Good Agreement

The conditions are studied in the paper of flooding the six plane blade impeller with blades inclined at the angle of 45° of relative size d/D = 1/3 and relative distance from the bottom of cylindrical vessel H2/D = 1/3 equipped at the wall with four radial baffles of width b/D = 0.1 at the relative vessel filling H/D = 1. The flooding conditions are determined experimentally from the course of dependence of the power input ratio of gassed and ungassed impeller on the flow rate number of air blown into the liquid phase (water) in the vessel. Theoretically, the conditions of the impeller flooding, when it is no more able to disperse air blown into the charge, are determined from balance of forces in the liquid flow leaving the region of rotating impeller acting on the bubbles of rising gas under the turbulent regime of charge flow. The results of the blade impeller frequency of revolutions determined theoretically at its flooding were found to be in good agreement with the experimentally determined values of the frequency of revolutions investigated obtained in the model equipment with vessel diameter D = 290 mm.

scholarly journals Study of Pumping Capacity of Pitched Blade Impellers

10.14311/380 ◽  
2002 ◽  
Vol 42 (4) ◽  
Author(s):  
I. Fořt ◽  
T. Jirout ◽  
R. Sperling ◽  
S. Jambere ◽  
F. Rieger
Keyword(s):  
Laser Doppler Anemometry ◽  
Radial Profile ◽  
Axial Flow ◽  
Power Input ◽  
Vessel Diameter ◽  
Energetic Efficiency ◽  
Turbulent Regime ◽  
Flat Bottom ◽  
Mean Velocity ◽  
Liquid Suspensions

A study was made of the pumping capacity of pitched blade impellers in a cylindrical pilot plant vessel with four standard radial baffles at the wall under a turbulent regime of flow. The pumping capacity was calculated from the radial profile of the axial flow, under the assumption of axial symmetry of the discharge flow. The mean velocity was measured using laser Doppler anemometry in a transparent vessel of diameter T = 400 mm, provided with a standard dished bottom. Three and six blade pitched blade impellers (the pitch angle varied within the interval a Îá24°; 45°ń) of impeller/vessel diameter ratio D/T = 0.36, as well as a three blade pitched blade impeller with folded blades of the same diameter, were tested. The calculated results were compared with the results of experiments mentioned in the literature, above all in cylindrical vessels with a flat bottom. Both arrangements of the agitated system were described by the impeller energetic efficiency, i.e, a criterion including in dimensionless form both the impeller energy consumption (impeller power input) and the impeller pumping effect (impeller pumping capacity). It follows from the results obtained with various geometrical configurations that the energetic efficiency of pitched blade impellers is significantly lower for configurations suitable for mixing solid-liquid suspensions (low impeller off bottom clearances) than for blending miscible liquids in mixing (higher impeller off bottom clearances).

Energetic efficiency of two impellers on the same shaft in a cylindrical baffled vessel of high height/diameter ratio

1989 ◽  
Vol 54 (9) ◽  
pp. 2345-2356 ◽  
Author(s):  
Ivan Fořt ◽  
Jiří Hájek ◽  
Václav Machoň
Keyword(s):  
High Speed ◽  
Power Input ◽  
Vessel Diameter ◽  
Diameter Ratio ◽  
Energetic Efficiency ◽  
Turbulent Regime ◽  
Inclined Plane ◽  
Pumping Effect ◽  
Charge Flow ◽  
Turbine Impeller

The paper deals with the experimental study of the indicating particle circulation and the impeller power input in a liquid mechanically agitated with two high-speed impellers (combination of the standard turbine impeller and the six inclined (at 45°) plane blades impeller) on the same shaft in a slender vessel (its height is equal double of the vessel diameter) equipped with four radial baffles at its walls under the turbulent regime of agitated charge flow. By the visual method of the indicating particle it is examined its circulation in the lower part of the system pumping effect of the lower impeller), its circulation in the upper part of the system (pumping effect of the upper impeller), and the exchangeable circulation between the upper and lower part of the system and vice versa. The impeller power input is ascertained from the measured current electricity in the anchor of the direct current driving motor. It follows from the calculated energetic efficiency (the ratio of the cube of the sum of the impeller flow rate numbers and the sum of the impeller power numbers) of the investigated combinations of impellers that the highest value of this quantity is exhibited for two standard turbine impellers on the same shaft and for a combination of the lower standard turbine impeller and the upper impeller with inclined plane blades pumping upwards; slightly less value of the impeller energetic efficiency appears for the combination of two impellers with six inclined plane blades, the upper one pumps liquid upwards and the lower one downwards. For all the configurations the vertical distance of impellers on the same shaft has to be longer than the vessel diameter.

A Model for Predicting Temperature of Electrofusion Joints for Polyethylene Pipes

2009 ◽  
Vol 131 (6) ◽  
Author(s):  
Jianfeng Shi ◽  
Jinyang Zheng ◽  
Weican Guo ◽  
Ping Xu ◽  
Yongquan Qin ◽  
...  
Keyword(s):  
Thermal Contact ◽  
Power Input ◽  
Ultrasonic Test ◽  
Thermal Contact Conductance ◽  
Transfer Model ◽  
Contact Conductance ◽  
One Dimensional ◽  
Polyethylene Pipes ◽  
Heating Wire ◽  
Good Agreement

With the increasing application of electrofusion (EF) welding in connecting polyethylene (PE) pipes for gas distribution, more effort has been invested to ensure the safety of the pipeline systems. The objective of this paper is to investigate and understand the temperature distribution during EF welding. A one-dimensional transient heat-transfer model was proposed, taking the variation in the rate of power input, the phase transition of PE, and the thermal contact conductance between heating wire and PE into consideration. Then, experiments were designed to verify the power input and the temperature. The measured values of the power input were shown to be in good agreement with the analytical results. Based on ultrasonic test (UT), a new “Eigen-line” method was presented, which overcomes the difficulties found in the thermocouples’ temperature measurements. The results demonstrate good agreements between prediction and experiment. Finally, based on the presented model, a detailed parametric study was carried out to investigate the influences of the variation in the power input, the physical properties of PE, and the thermal contact conductance between heating wire and surrounding PE.

Comments on "Experimental Studies and CFD Modeling on the Effects of a Cut in the Baffle on Power Consumption"

2009 ◽  
Vol 4 (1) ◽  
Author(s):  
Ivan Fort
Keyword(s):  
Power Consumption ◽  
Cfd Simulation ◽  
Experimental Studies ◽  
Power Input ◽  
Cfd Modeling ◽  
Turbulent Regime

Critical comments on results of the CFD simulation of the impeller power input in a cylindrical baffled vessel under turbulent regime of flow of agitated liquid.

Experimental Verification of a New Model for Transition Flow of Thin Films in Long Journal Bearings

2010 ◽  
Author(s):  
Dingfeng Deng ◽  
Minel J. Braun
Keyword(s):  
Experimental Verification ◽  
Journal Bearing ◽  
Flow Behavior ◽  
Journal Bearings ◽  
Turbulent Regime ◽  
Transition Flow ◽  
New Model ◽  
Taylor Vortices ◽  
The Difference ◽  
Good Agreement

A new model for predicting the flow behavior in long journal bearing films in the transition regime (Taylor and wavy vortex regimes) was previously proposed by the authors. This paper presents the experimental verification. A comparison between the experimental and numerical results of the Torque–Speed graphs is presented with good agreement between the numerical and experimental data for the Couette, Taylor and pre-wavy regimes. In the wavy and turbulent regime, the magnitude of the numerically obtained data is larger than the corresponding measured torques, but the difference is confined to below 14%. A comparison between experimental and numerical flow patterns is also presented. The results match well in general, except that experimentally, a pre-wavy regime was identified. The latter is characterized by the disappearance of the Taylor vortices, while numerically the Taylor vortices are only distorted and the wavy vortices are formed in this regime.

Liquid circulation in a cylindrical vessel with radial baffles and inclined blade impeller

1989 ◽  
Vol 54 (6) ◽  
pp. 1599-1611
Author(s):  
Ivan Fořt ◽  
Miloslav Hošťálek ◽  
Jaroslav Medek
Keyword(s):  
Stream Function ◽  
Stokes Equations ◽  
Laser Doppler Anemometry ◽  
Relative Size ◽  
Power Input ◽  
Cylindrical Vessel ◽  
Flat Bottom ◽  
Mean Velocity ◽  
Liquid Circulation ◽  
Radial Profiles

Liquid circulation was studied in a cylindrical vessel with radial baffles under the turbulent flow regime of liquid agitated gradually with the following types of four inclined blade impellers: impeller with plane blades inclined at the angle of 25°; impeller with asymmetrically profiled blades at the angle of 30°-17°; impeller with strength-profiled blades. By solving the turbulent (vortex) analogy of the Stokes equations for the creeping (non-inertial) laminar flow, the streamline distribution (the Stokes stream function) in the bulk of agitated charge was obtained for each of impellers studied (relative size d/D = 1/3, relative distance from the bottom H2/D = 1/3, relative vessel filling H/D = 1), placed axisymmetrically in the vessel and pumping the liquid towards its flat bottom. The zero values of the Stokes stream function at the bottom, walls, and charge liquid level, and further the radial profiles of axial and radial component of mean velocity in the cross sections under and above the impeller obtained experimentally by the laser-doppler anemometry on the assumption of axial symmetry of the agitated system studied were set as the boundary conditions for the solution of the partial differential equation considered. It follows from the results obtained that the homogenous circulation of agitated charge at the relatively lowest value of the impeller power input is reached when agitating with the asymmetrically profiled blade impeller which therefore can successfully replace the propeller mixer with airfoil profiled blades.

scholarly journals Mixing Performance Analysis of Orbitally Shaken Bioreactors

2020 ◽  
Vol 10 (16) ◽  
pp. 5597
Author(s):  
Angus Shiue ◽  
Shih-Chieh Chen ◽  
Jyh-Cheng Jeng ◽  
Likuan Zhu ◽  
Graham Leggett
Keyword(s):  
Mixing Time ◽  
Power Input ◽  
Energy Dissipation Rate ◽  
Mixing Efficiency ◽  
Thermal Method ◽  
Turbulent Regime ◽  
Mixing Process ◽  
Dimensionless Numbers ◽  
Filling Volume ◽  
Input Variables

This study investigated the efficacy of a novel correlation of power input, energy dissipation rate and mixing time as a potential route to identify the orbitally shaken bioreactor (OSB) system. The Buckingham’s π-theorem was used to designate and transform dimensionless Newton numbers with five relevant power input variables. These variables were empirically varied to evaluate the correlation among the dimensionless numbers. The Newton number decreases with the increased shaking frequency and filling volume. Previous work has focused on optimizing the mixing process by evaluating different shaking and agitation mixing methods. We establish a new mixing process and assessable measurement of the mixing time in the OSB. An innovative explanation of mixing time for the thermal method is proposed. The optimal mixing time is independent of the temperature of filled liquid. The dimensionless mixing number remained constant in the turbulent regime and increasing with the increased liquid viscosity and filling volume. Our findings revealed that the observed correlation is a practical tool to figure the power consumption and mixing efficiency as cell cultivation in all OSB scales and is fully validated when scaling–up system.

scholarly journals Power Input of High-Speed Rotary Impellers

10.14311/280 ◽  
2001 ◽  
Vol 41 (6) ◽  
Author(s):  
K. R. Beshay ◽  
J. Kratěna ◽  
I. Fořt ◽  
O. Brůha
Keyword(s):  
Pitch Angle ◽  
High Speed ◽  
Power Input ◽  
Cylindrical Vessel ◽  
Turbulent Regime ◽  
Power Dependence ◽  
Rushton Turbine ◽  
Weak Influence ◽  
Turbine Impeller ◽  
Blade Pitch Angle

This paper presents the results of an experimental investigation of the power input of pitched blade impellers and standard Rushton turbine impellers in a cylindrical vessel provided with four radial baffles at its wall under a turbulent regime of flow of an agitated liquid. The influence of the geometry of the pitched blade impellers (pitch angle, number of blades) and the off-bottom impeller clearance of both high-speed impellers tested on the impeller power input is determined in two sizes of the cylindrical vessel (0.3 m and 0.8 m diameter of vessel). A strain gauge torquemeter is used in the small vessel and a phase shift mechanical torquemeter is used in the large vessel. All results of the experiments correspond to the condition that the Reynolds number modified for the impeller exceeds ten thousand. The results of this study show that the significant influence of the separating disk thickness of the turbine impeller corresponds fairly well to the empirical equations presented in the literature. Both the influence of the number of impeller blades and the blade pitch angle of the pitched blade impeller were expressed quantitatively by means of the power dependence of the recently published correlations: the higher the pitch angle and the number of blades, the higher the values of the impeller power input. Finally, it follows from results of this study that the impeller off-bottom clearance has a weak influence on the power input of the Rushton turbine impeller, but with decreasing impeller off-bottom clearance the power input of the pitched blade impeller increases significantly.

Effects of type and number of impellers and liquid viscosity on the power characteristics of mechanically agitated gas—liquid systems

2007 ◽  
Vol 61 (1) ◽  
Author(s):  
R. Adamiak ◽  
J. Karcz
Keyword(s):  
Fluid Flow ◽  
Power Consumption ◽  
High Speed ◽  
Vessel Diameter ◽  
Turbulent Regime ◽  
Relative Power ◽  
Liquid Viscosity ◽  
Power Characteristics ◽  
Liquid Systems ◽  
Inner Diameter

AbstractEffect of the type and number of high-speed impellers installed on a common shaft on the power characteristics was investigated in water and glucose solutions of different concentration. Different configurations of the Rushton or Smith turbines, pitched blade turbines, propeller, and A 315 impeller were tested. Measurements of power consumption were carried out within the transitional and turbulent regime of the fluid flow using the strain gauge method. Baffled agitated vessels with inner diameter of 0.288 m and 0.634 m were used for the experiments. Liquid height in the vessels was equal to the vessel diameter or it was twice higher. The relative power consumption was compared for different configurations of the impellers.

Thermohydrodynamic Analysis of Process-Liquid Hydrostatic Journal Bearings in Turbulent Regime, Part II: Numerical Solution and Results

1995 ◽  
Vol 62 (3) ◽  
pp. 679-684 ◽  
Author(s):  
Zhou Yang ◽  
L. San Andres ◽  
D. W. Childs
Keyword(s):  
Journal Bearing ◽  
Nonlinear Differential Equations ◽  
Flow Characteristics ◽  
Turbulent Regime ◽  
Fluid Temperature ◽  
Numerical Predictions ◽  
Exit Temperature ◽  
Direct Stiffness ◽  
Stiffness And Damping ◽  
Good Agreement

A finite difference scheme is implemented to solve the nonlinear differential equations describing the turbulent bulk-flow on the film lands of a hydrostatic journal bearing (HJB). A Newton-Raphson scheme is used to update the recess pressures and to satisfy the mass continuity requirement at each bearing recess. Comparisons of numerical predictions from the thermohydrodynamic (THD) model with experimental measurements of mass flow rate, fluid temperature, and static stiffness coefficient from a LH2 test HJB article show very good agreement. In particular, the exit temperature of the bearing is lower than the supply temperature; i.e., the liquid temperature decreases along the bearing length. Similar values of direct stiffness and damping coefficients are predicted by the adiabatic THD model and other considering isothermal flow characteristics. However, the THD model predicts lower cross-coupled stiffness and whirl frequency ratio (WFR < 0.5). The results show that for the application presented, the LH2 hydrostatic bearing is more stable than previously thought.

Sign in / Sign up

Export Citation Format

Share Document