Theory of motion in an optical radiation field for sublimating spherical aerosol solid particles with inhomogeneous thermal conductivity

2005 ◽  
Vol 50 (7) ◽  
pp. 333-336
Author(s):  
Yu. I. Yalamov ◽  
A. S. Khasanov
Keyword(s):  
Thermal Conductivity ◽  
Radiation Field ◽  
Optical Radiation ◽  
Solid Particles ◽  
Theory Of Motion

Pool Boiling Characteristics of Metallic Nanofluids

2011 ◽  
Vol 133 (11) ◽  
Author(s):  
K. Hari Krishna ◽  
Harish Ganapathy ◽  
G. Sateesh ◽  
Sarit K. Das
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Boiling Heat Transfer ◽  
Volume Fraction ◽  
Pool Boiling ◽  
Heat Fluxes ◽  
Solid Particles ◽  
Heater Surface ◽  
Heat Transfer Characteristics ◽  
Transfer Characteristics

Nanofluids, solid-liquid suspensions with solid particles of size of the order of few nanometers, have created interest in many researchers because of their enhancement in thermal conductivity and convective heat transfer characteristics. Many studies have been done on the pool boiling characteristics of nanofluids, most of which have been with nanofluids containing oxide nanoparticles owing to the ease in their preparation. Deterioration in boiling heat transfer was observed in some studies. Metallic nanofluids having metal nanoparticles, which are known for their good heat transfer characteristics in bulk regime, reported drastic enhancement in thermal conductivity. The present paper investigates into the pool boiling characteristics of metallic nanofluids, in particular of Cu-H2O nanofluids, on flat copper heater surface. The results indicate that at comparatively low heat fluxes, there is deterioration in boiling heat transfer with very low particle volume fraction of 0.01%, and it increases with volume fraction and shows enhancement with 0.1%. However, the behavior is the other way around at high heat fluxes. The enhancement at low heat fluxes is due to the fact that the effect of formation of thin sorption layer of nanoparticles on heater surface, which causes deterioration by trapping the nucleation sites, is overshadowed by the increase in microlayer evaporation, which is due to enhancement in thermal conductivity. Same trend has been observed with variation in the surface roughness of the heater as well.

Evaluation of the Temperature Oscillation Technique to Calculate Thermal Conductivity of Water and Systematic Measurement of the Thermal Conductivity of Aluminum Oxide – Water Nanofluid

2004 ◽  
Author(s):  
P. Bhattacharya ◽  
S. Nara ◽  
P. Vijayan ◽  
T. Tang ◽  
W. Lai ◽  
...  
Keyword(s):  
Thermal Conductivity ◽  
Aluminum Oxide ◽  
Effective Thermal Conductivity ◽  
Base Fluid ◽  
Suspended Solid ◽  
Temperature Oscillation ◽  
Solid Particles ◽  
Systematic Measurement ◽  
Experimental Setup ◽  
Suspended Solid Particles

A nanofluid is a fluid containing suspended solid particles, with sizes of the order of nanometers. The nanofluids are better conductors of heat than the base fluid itself. Therefore it is of interest to measure the effective thermal conductivity of such a nanofluid. We use temperature oscillation technique to measure the thermal conductivity of the nanofluid. However, first we evaluate the temperature oscillation technique as a tool to measure thermal conductivity of water. Then we validate our experimental setup by measuring the thermal conductivity of the aluminum oxide-water nanofluid and comparing our results with previously published work. Finally, we do a systematic series of measurements of the thermal conductivities of aluminum oxide-water nanofluids at various temperatures and explain the reasons behind the dependence of the enhancement in thermal conductivity of the nanofluid on temperature.

scholarly journals Implicit Finite Difference Simulation of Prandtl-Eyring Nanofluid over a Flat Plate with Variable Thermal Conductivity: A Tiwari and Das Model

Mathematics ◽  
2021 ◽  
Vol 9 (24) ◽  
pp. 3153
Author(s):  
Nidal H. Abu-Hamdeh ◽  
Abdulmalik A. Aljinaidi ◽  
Mohamed A. Eltaher ◽  
Khalid H. Almitani ◽  
Khaled A. Alnefaie ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Finite Difference ◽  
Differential Equations ◽  
Ordinary Differential Equations ◽  
Variable Thermal Conductivity ◽  
Solid Particles ◽  
Engine Oil ◽  
Working Fluid ◽  
Implicit Finite Difference

The current article presents the entropy formation and heat transfer of the steady Prandtl-Eyring nanofluids (P-ENF). Heat transfer and flow of P-ENF are analyzed when nanofluid is passed to the hot and slippery surface. The study also investigates the effects of radiative heat flux, variable thermal conductivity, the material’s porosity, and the morphologies of nano-solid particles. Flow equations are defined utilizing partial differential equations (PDEs). Necessary transformations are employed to convert the formulae into ordinary differential equations. The implicit finite difference method (I-FDM) is used to find approximate solutions to ordinary differential equations. Two types of nano-solid particles, aluminium oxide (Al2O3) and copper (Cu), are examined using engine oil (EO) as working fluid. Graphical plots are used to depict the crucial outcomes regarding drag force, entropy measurement, temperature, Nusselt number, and flow. According to the study, there is a solid and aggressive increase in the heat transfer rate of P-ENF Cu-EO than Al2O3-EO. An increment in the size of nanoparticles resulted in enhancing the entropy of the model. The Prandtl-Eyring parameter and modified radiative flow show the same impact on the radiative field.

An Investigation of the Effect of Nanoparticles on the Effectiveness of a Heat Exchanger

2007 ◽  
Author(s):  
V. Upender Rao ◽  
V. Sajith ◽  
T. Hanas ◽  
C. B. Sobhan
Keyword(s):  
Thermal Conductivity ◽  
Heat Exchanger ◽  
Operating Temperature ◽  
Particle Surface ◽  
Weight Fraction ◽  
Copper Oxide Nanoparticles ◽  
Suspended Solid ◽  
Solid Particles ◽  
Particle Surface Area ◽  
Materials Used

Convective heat transfer can be improved by enhancing the thermal conductivity of the fluid. It has been established that fluids containing suspended solid particles of metallic origin in nanoscale dimensions, display enhanced thermal conductivity. Nanoparticle suspensions have superior qualities than suspensions of larger sized particles, such as more particle surface area, less possibilities of agglomeration and clogging and better stability. An experimental investigation on the effect of the inclusion of nanoparticles into the cooling fluid on the effectiveness of a heat exchanger is presented in this paper. An experimental double pipe heat exchanger with the hot fluid flowing through the inner tube was used in the study. Aluminum oxide and copper oxide nanoparticles with a size range of 20 to 30 nm suspended in water using ultrasonic agitation was used as the hot fluid, and water was used as the cold fluid passing through the annulus. The concentration of the suspended nanoparticles was varied to investigate its effect on the performance of the exchanger. The operating temperature is also used as a parameter in the study. Typically, an enhancement of 4.5 to 7 percent was observed in the effectiveness of the heat exchanger for 0.26% weight fraction of the nanoparticles in suspension, in an operating temperature range of 50–70°C. The effectiveness of the heat exchanger was found to increase with the concentration of nanoparticles for both materials used.

Determining the Effective Thermal Conductivity of a Nanofluid Using Brownian Dynamics Simulation

2003 ◽  
Author(s):  
P. Bhattacharya ◽  
S. K. Saha ◽  
A. Yadav ◽  
P. E. Phelan ◽  
R. S. Prasher
Keyword(s):  
Thermal Conductivity ◽  
Brownian Motion ◽  
Effective Thermal Conductivity ◽  
Brownian Dynamics ◽  
Volume Fraction ◽  
Particle Volume Fraction ◽  
Solid Particles ◽  
Dynamics Simulation ◽  
Fluid Viscosity ◽  
Brownian Dynamics Simulation

A nanofluid is a fluid containing suspended solid particles, with sizes of the order of nanometers. Normally the fluid has a low thermal conductivity compared to the suspended particles. Therefore introduction of these particles into the fluid increases the effective thermal conductivity of the system. It is of interest to predict the effective thermal conductivity of such a nanofluid under different conditions like varying particle volume fraction, varying particle size, changing fluid conductivity or changing fluid viscosity, especially since only limited experimental data are available. Also, some controversy exists about the role of Brownian motion in enhancing the nanofluid’s thermal conductivity. We have developed a novel technique to compute the effective thermal conductivity of a nanofluid using Brownian dynamics simulation, which has the advantage of being computationally less expensive than molecular dynamics. We obtain the contribution of the nanoparticles towards the effective thermal conductivity using the equilibrium Green-Kubo method. Then we combine that with the thermal conductivity of the base fluid to obtain the effective thermal conductivity of the nanofluid, and thus are able to show that the Brownian motion contributes greatly to the thermal conductivity.

Development of a Metal Micro-Textured Thermal Interface Material

2009 ◽  
Author(s):  
R. Kempers ◽  
R. Frizzell ◽  
A. Lyons ◽  
A. J. Robinson
Keyword(s):  
Thermal Conductivity ◽  
Applied Pressure ◽  
Solid Particles ◽  
High Thermal Conductivity ◽  
Thermal Interface Material ◽  
Filler Materials ◽  
Mechanical And Thermal Properties ◽  
Metal Foil ◽  
Thermal Interface ◽  
Thermally Conductive

Typical thermal interface materials (TIMs) consist of high thermal conductivity solid particles dispersed in a continuous, low thermal conductivity organic compound. Despite using filler materials of very high thermal conductivity, the effective thermal conductivity of these TIMs is often two orders of magnitude lower than the pure filler materials. In addition, dispensing and flow of the particle-matrix composite results in voids being trapped within the bond. To address these issues, a novel metal micro-textured thermal interface material (MMT-TIM) has been developed. This material consists of a thin metal foil with raised micro-scale features that plastically deform under an applied pressure thereby creating a continuous, thermally conductive, path between the mating surfaces. Numerical tools have been developed that couple the mechanical and thermal properties and behaviour of MMT-TIMs as they undergo large-plastic deformation during assembly. This study presents the modelling approach and predictions of MMT-TIM performance based on these numerical techniques. The predictions show good agreement with experimental results, which were obtained using prototype MMT-TIMs and an advanced TIM characterization facility. Finally, a future outlook for this technology is presented based on these promising initial results.

scholarly journals Performance Analysis of Shell and Tube Type Heat Exchanger Using Aluminium Oxide (Al2O3) Nano-Particle

2021 ◽  
Vol 9 (9) ◽  
pp. 157-164
Author(s):  
Paritosh Singh
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Transfer Coefficient ◽  
Heat Exchanger ◽  
Transfer Coefficient ◽  
Solid Particles ◽  
Tube Heat Exchanger ◽  
Overall Heat Transfer Coefficient ◽  
Shell And Tube ◽  
Evacuated Tube

Abstract: Research in convective heat transfer using suspensions of nanometer sized solid particles in a base fluid started only over the past decade. Recent investigations on nanofluids, as such suspensions are often called, indicate that the suspended nanoparticles markedly change the transport properties and heat transfer characteristics of the suspension. The very first part of the research work summarizes about the various thermo physical properties of Al2O3 Nanofluid. In evacuated tube solar water heating system nanofluids are used as primary fluid and DM water as secondary fluid in Shell and Tube Heat Exchanger. The experimental analysis of Shell and Tube heat exchanger integrated with Evacuated tube solar collector have been carried out with two types of primary fluids. Research study of shell and tube heat exchanger is focused on heat transfer enhancement by usage of nano fluids. Conventional heat transfer fluids have inherently low thermal conductivity that greatly limits the heat exchange efficiency. The result of analysis shows that average relative variation in LMTD and overall heat transfer coefficient is 24.56% and 52.0% respectively. The payback period of system is reduced by 0.4 years due to saving is in replacement cost of Evacuated Tube Collector. Keywords: ETC; Nanofluid; LMTD; Thermal Conductivity; Overall heat transfer coefficient

scholarly journals Investigation of heat transfer enhancement in an annular conduit with angled fins using functionalized GNP colloidal suspension

2021 ◽  
Vol 945 (1) ◽  
pp. 012058
Author(s):  
Sayshar Ram Nair ◽  
Cheen Sean Oon ◽  
Ming Kwang Tan ◽  
S.N. Kazi
Keyword(s):  
Heat Transfer ◽  
Thermal Conductivity ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Power Plants ◽  
Colloidal Suspension ◽  
Industrial Applications ◽  
Point Of View ◽  
Solid Particles ◽  
Working Fluid

Abstract Heat exchangers are important equipment with various industrial applications such as power plants, HVAC industry and chemical industries. Various fluids that are used as working fluid in the heat exchangers such as water, oil, and ethylene glycol. Researchers have conducted various studies and investigations to improve the heat exchanger be it from material or heat transfer point of view. There have been attempts to create mixtures with solid particles suspended. This invention had some drawbacks since the pressure drop was compromised, on top of the occurrence of sedimentation or even erosion, which incurs higher maintenance costs. A new class of colloidal suspension fluid that met the demands and characteristics of a heat exchanger was then created. This novel colloidal suspension mixture was then and now addressed as “nanofluid”. In this study, the usage of functionalized graphene nanoplatelet (GNP) nanofluids will be studied for its thermal conductivity within an annular conduit with angled fins, which encourage swirling flows. The simulation results for the chosen GNP nanofluid concentrations have shown an enhancement in thermal conductivity and heat transfer coefficient compared to the corresponding base fluid thermal properties. The data from this research is useful in industrial applications which involve heat exchangers with finned tubes.

Sign in / Sign up

Export Citation Format

Share Document