The Effect of Small Amounts of Long and Short Branches on the Steady State Flow Behavior of Polyethylene‐Wax Blends: Application of Concentration Superposition

1971 ◽  
Vol 15 (4) ◽  
pp. 647-662 ◽  
Author(s):  
Nobuyuki Nakajima ◽  
Casper F. Stark ◽  
Ray D. Hoffman
Keyword(s):  
Steady State ◽  
Flow Behavior ◽  
Steady State Flow ◽  
State Flow ◽  
Polyethylene Wax

Steady-State Flow Behavior of CO2 Foam

2004 ◽  
Author(s):  
J.S. Kim ◽  
Y. Dong ◽  
W.R. Rossen
Keyword(s):  
Steady State ◽  
Flow Behavior ◽  
Steady State Flow ◽  
State Flow ◽  
Co2 Foam

Effect of Grain Size on Mechanical Properties of Single Phase Co-Ni-Cr-Mo Based Superalloy

2005 ◽  
Vol 475-479 ◽  
pp. 631-634 ◽  
Author(s):  
Jun Kyung Sung ◽  
Mok Soon Kim ◽  
Won Yong Kim ◽  
Akihiko Chiba
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Grain Size ◽  
Steady State ◽  
Yield Strength ◽  
Flow Behavior ◽  
Strain Curve ◽  
Steady State Flow ◽  
State Flow ◽  
Average Grain Size

A recrystallized Co-Ni-Cr-Mo based superalloy was produced by cold working of 72% and subsequent recrystallization heat treatment. Microstructural observation revealed that a full recrystallization of the cold-worked alloy occured when heat treatment was performed at and above 1273K for 1h. So that, recrystallization heat treatment was carried out in a temperature range from 1273K to 1473K for 1h~24h, by which the average grain size was controlled to 28µm～238µm. Tensile tests were carried out from room temperature (RT) to 1073K in order to understand the effect of grain size on the mechanical properties of the Co-Ni-Cr-Mo based superalloy. At RT and 943K, yield strength, tensile strength and elongation of the recrystallized alloy were improved with decreasing grain size. The alloy having a grain size less than 42µm exhibited a steady-state flow behavior in the true stress-true strain curve at 943K. However, the alloy having a grain size of 28µm showed lower yield strength than that of 42µm at 1073K. It was found that the steady state flow is closely related to the occurrence of {111}<112> deformation twinning in the Co-Ni-Cr-Mo based superalloy.

A study on the steady-state flow behavior of the flashing-driven open natural circulation system

2021 ◽  
Vol 182 ◽  
pp. 115903
Author(s):  
Xiaofan Hou ◽  
Jinrong Qiu ◽  
Zhongning Sun ◽  
Shiwei Yao ◽  
Chuan He ◽  
...  
Keyword(s):  
Steady State ◽  
Natural Circulation ◽  
Flow Behavior ◽  
Circulation System ◽  
Steady State Flow ◽  
State Flow

Steady-State Flow Behavior of CO2 Foam

SPE Journal ◽  
2005 ◽  
Vol 10 (04) ◽  
pp. 405-415 ◽  
Author(s):  
Jisung Kim ◽  
Yan Dong ◽  
William R. Rossen
Keyword(s):  
Steady State ◽  
Flow Behavior ◽  
Steady State Flow ◽  
State Flow ◽  
Co2 Foam

Characterization of polypropylene according to steady-state flow behavior

1965 ◽  
Vol 9 (9) ◽  
pp. 3141-3152 ◽  
Author(s):  
Nobuyuki Nakajima ◽  
Patrick S. L. Wong
Keyword(s):  
Steady State ◽  
Flow Behavior ◽  
Steady State Flow ◽  
State Flow

Calibration 7" – Cutthroat Flume as New Size for Discharge Measurement at Free Flow Condition

2020 ◽  
Vol 38 (12A) ◽  
pp. 1783-1789
Author(s):  
Jaafar S. Matooq ◽  
Muna J. Ibraheem
Keyword(s):  
Steady State ◽  
Flow Condition ◽  
Laboratory Experiments ◽  
Free Flow ◽  
Experimental Program ◽  
Steady State Flow ◽  
Empirical Formulas ◽  
State Flow ◽  
Operation Conditions ◽  
Throat Width

 This paper aims to conduct a series of laboratory experiments in case of steady-state flow for the new size 7 ̋ throat width (not presented before) of the cutthroat flume. For this size, five different lengths were adopted 0.535, 0.46, 0.40, 0.325 and 0.27m these lengths were adopted based on the limitations of the available flume. The experimental program has been followed to investigate the hydraulic characteristic and introducing the calibrated formula for free flow application within the discharge ranged between 0.006 and 0.025 m3/s. The calibration result showed that, under suitable operation conditions, the suggested empirical formulas can accurately predict the values of discharge within an error ± 3%.

A Graphical Method for Storage Coefficient Determination from Quasi-Steady State Flow Data

1996 ◽  
Vol 27 (4) ◽  
pp. 247-254 ◽  
Author(s):  
Zekâi Şen
Keyword(s):  
Steady State ◽  
Graphical Method ◽  
Pumping Test ◽  
Quasi Steady State ◽  
Flow Data ◽  
Steady State Flow ◽  
Storage Coefficient ◽  
State Flow ◽  
Aquifer Test

A simple, approximate but practical graphical method is proposed for estimating the storage coefficient independently from the transmissivity value, provided that quasi-steady state flow data are available from a pumping test. In the past, quasi-steady state flow distance-drawdown data have been used for the determination of transmissivity only. The method is applicable to confined and leaky aquifers. The application of the method has been performed for various aquifer test data available in the groundwater literature. The results are within the practical limits of approximation compared with the unsteady state flow solutions.

Sign in / Sign up

Export Citation Format

Share Document