Dynamic Intrinsic Viscosity of Macromolecules with Internal Viscosity. III. Effect of Molecular Weight, Excluded Volume, and Hydrodynamic Interaction

1967 ◽  
Vol 11 (1) ◽  
pp. 15-37 ◽  
Author(s):  
A. Peterlin ◽  
Chr. Reinhold
Keyword(s):  
Molecular Weight ◽  
Intrinsic Viscosity ◽  
Hydrodynamic Interaction ◽  
Excluded Volume ◽  
Internal Viscosity

Effect on Polymer Chain Structure Caused by the Molar Fraction of 4-Hydroxybutyrate in Poly(3-hydroxybutyrate- co -4-hydroxybutyrate)

2012 ◽  
Vol 602-604 ◽  
pp. 776-780
Author(s):  
Zhi Qiang Li ◽  
Mei Li ◽  
Wei Jia Fan
Keyword(s):  
Molecular Weight ◽  
Intrinsic Viscosity ◽  
Polymer Chain ◽  
Molar Fraction ◽  
Chain Structure ◽  
The Other ◽  
Mean Square ◽  
Polarizing Microscope ◽  
Other Hand ◽  
The Mean

Poly(3-hydroxybutyrate-co-4-hydroxybutyrate)copolymer [P(3HB-co-4HB)] is a kind of biodegradable high molecular polymer produced by bioaccumulation. Because of the good biodegradability and biocompatibility, P(3HB-co-4HB)s have attracted wide attention . At first, the intrinsic viscosity[η] in good solvent of P(3HB-co-4HB) s with varying contents of 4HB was investigated in different temperature. Second, observed the changes of crystallization gathered state caused by the varying contents of 4HB by polarizing microscope. The results show that to the P(3HB-co-4HB)s in same molecular weight, the intrinsic viscosity[η] in good solvent barely changes when the mole fractions of 4HB increase. On the other hand, the mean square end to end distances[0] of macromolecular flexible chains increase with the mole fractions of 4HB. At the same time, the states of aggregation change from spherulites to dendrites. In this investigation, we discuss the reasons of the differences in depth.

Sorption of GR-S Type of Polymer on Carbon Black. III. Sorption by Commercial Blacks

1953 ◽  
Vol 26 (1) ◽  
pp. 102-114 ◽  
Author(s):  
I. M. Kolthoff ◽  
R. G. Gutmacher
Keyword(s):  
Molecular Weight ◽  
Carbon Black ◽  
Intrinsic Viscosity ◽  
Benzene Solution ◽  
Weight Fraction ◽  
High Molecular Weight Fraction ◽  
Molecular Weights ◽  
Bound Rubber ◽  
Flow Through ◽  
Peculiar Behavior

Abstract The sorption capacities toward GR-S five commercial carbon blacks are in decreasing order: Spheron-6, Vulcan-1, Philblack-0, Sterling-105, Philblack-A. Apparently, the sorption is not related to surface area. The sorption on Vulcan-1 of GR-S from its solutions in seven different solvents or mixtures of solvents increases with decreasing solvent power for the rubber. The sorption curves of two “cold rubbers,” polymerized at −10 and +5° respectively, showed little difference from that of 50° GR-S. Previous heating of carbon black in nitrogen at 500 or 1100° increased the sorption by about 20 per cent over unheated carbon. Air-heating of carbon black at 425° did not cause a difference in the sorption from benzene solution, but produced an increase in the sorption of rubber from n-heptane solution. In the range 75% butadiene-25% styrene to 5% butadiene-95% styrene, there is practically no effect of the degree of unsaturation on the sorption. Polystyrene of high intrinsic viscosity exhibits a peculiar behavior with furnace blacks. Vulcan-1 sorbed microgel as well as the sol fraction from n-heptane solutions of GR-S containing microgel (conversion 74.7 and 81.5 per cent). There was no appreciable difference in the amount of sorption of rubber fractions having average molecular weights varying from 433,000 to 85,000. There is little change in the amount sorbed after two hours of shaking, but the intrinsic viscosity of the residual rubber decreases with time. The low molecular-weight rubber is sorbed more rapidly, but is slowly replaced by the more tightly sorbed high molecular weight fraction. Partial fractionation of a rubber sample can be achieved by allowing the rubber solution to flow through a column of weakly sorbing carbon black. A large portion of the sorbed rubber can be recovered from the column by washing it with a good solvent such as xylene. Bound rubber is produced by intimate mixing of equal parts of carbon black and rubber swollen in chloroform, when the mixture is dried in vacuum at 80° or at room temperature. Milling is not essential to get bound rubber.

Sign in / Sign up

Export Citation Format

Share Document