Structural intensity in a line‐excited infinite elastic plate in the high‐frequency range

2000 ◽  
Vol 107 (5) ◽  
pp. 2853-2853
Author(s):  
Sabih I. Hayek ◽  
Jungyun Won
Keyword(s):  
Elastic Plate ◽  
High Frequency ◽  
High Frequency Range ◽  
Frequency Range ◽  
Structural Intensity

Electromagnetic Property of La0.7Sr0.3MnO3/Ag Composite at High Frequency

2015 ◽  
Vol 655 ◽  
pp. 182-185
Author(s):  
Ke Lan Yan ◽  
Run Hua Fan ◽  
Min Chen ◽  
Kai Sun ◽  
Xu Ai Wang ◽  
...  
Keyword(s):  
High Frequency ◽  
Single Phase ◽  
Low Frequency ◽  
Electromagnetic Property ◽  
High Frequency Range ◽  
Frequency Range ◽  
Free Electron Concentration ◽  
Theoretical Simulation ◽  
Electrical And Magnetic Properties ◽  
Three Phase

The phase structure, and electrical and magnetic properties of La0.7Sr0.3MnO3(LSMO)-xAg (xis the mole ratio,x=0, 0.3, 0.5) composite were investigated. It is found that the sample withx=0 is single phase; the samples withx=0.3 and 0.5 present three phase composite structure of the manganese oxide and Ag. With the increasing of Ag content, the grain size of the samples increases and the grain boundaries transition from fully faceted to partially faceted. The permittivity of spectrum (10 MHz - 1 GHz) and the theoretical simulation reveal that the plasma frequencyfpincrease with Ag content, due to the increasing of free electron concentration, which is further supported by the enhancement of conductivity. While for the permeability (μr'), theμr'decrease with the increasing of Ag content at low frequency range (f< 20 MHz), while at the relative high frequency range (f> 300 MHz), theμr'increased with Ag content. Therefore, the introduction of elemental Ag resulted in a higherμr'at the relative high frequency range.

An Impedance-Based Approach for Rods With Shear-Type Damping Layer Treatment

2013 ◽  
Vol 135 (1) ◽  
Author(s):  
P. W. Wang ◽  
D. Q. Zhuang
Keyword(s):  
High Frequency ◽  
Continuous Model ◽  
Damping Coefficient ◽  
System Response ◽  
Traditional Model ◽  
Constrained Layer Damping ◽  
High Frequency Range ◽  
Frequency Range ◽  
Shear Type ◽  
Shear Spring

An impedance-based approach for analyzing an axial rod with shear-type damping layer treatment is proposed. The rod and shear-type damping layer are regarded as two subsystems and both impedances are calculated analytically. The system impedance can be obtained through the impedance coupling between the host rod and the damping layer. The shear-type damping layer is regarded as a shear spring with complex shear modulus. Under the traditional model, the damping coefficient diminishes with the increasing frequency. The paper develops two shear-type damping layer models, including the single degree-of-freedom (SDOF) model and continuous model to predict the behavior of the damping layer. Both damping layer models are compared with the traditional model and the system responses from these models are validated by finite element method (FEM) code COMSOL Multiphysics. Results show that the damping coefficients of both the traditional shear-spring model and SDOF model diminish as the increasing frequency so that the system responses are discrepant with that from COMSOL in the high frequency range. On the other hand, the system response from the continuous model is consistent with that from COMSOL in the full frequency range. Hence, the continuous damping layer model can predict a correct damping coefficient in the high frequency range and this property can be also employed to improve the analysis of the constrained-layer damping treated structures. Finally, the modal loss factor and fundamental frequency of the system with respect to different damping layer thicknesses are presented using the developed approach.

Electromagnetic properties of porous 3D carbon-based structures in high frequency range

2021 ◽  
pp. 76-83
Author(s):  
E.G. Shashkova ◽  
◽  
N.I. Valunets ◽  
M.I. Demidenko ◽  
A.G. Paddubskaya ◽  
...  
Keyword(s):  
High Frequency ◽  
Electromagnetic Properties ◽  
High Frequency Range ◽  
Frequency Range ◽  
Carbon Based
Sign in / Sign up

Export Citation Format

Share Document