An experimental and numerical investigation of sound produced by low‐speed flow over a cavity with a leading edge overhang

2000 ◽  
Vol 107 (5) ◽  
pp. 2824-2824
Author(s):  
Brenda S. Henderson ◽  
Homayun K. Navaz ◽  
Raymond Berg
Keyword(s):  
Numerical Investigation ◽  
Leading Edge ◽  
Low Speed ◽  
Speed Flow ◽  
Flow Over A Cavity

Numerical Investigation of the Solidity Effect on Linear Compressor Cascades

2014 ◽  
Author(s):  
J. Sans ◽  
M. Resmini ◽  
J.-F. Brouckaert ◽  
S. Hiernaux
Keyword(s):  
Numerical Investigation ◽  
State Of The Art ◽  
Leading Edge ◽  
Operating Conditions ◽  
Compressor Cascade ◽  
Minimum Loss ◽  
Low Speed ◽  
High Mach ◽  
The Stability ◽  
The Impact

Solidity in compressors is defined as the ratio of the aerodynamic chord over the peripheral distance between two adjacent blades, the pitch. This parameter is simply the inverse of the pitch-to-chord ratio generally used in turbines. Solidity must be selected at the earliest design phase, i.e. at the level of the meridional design and represents a crucial step in the whole design process. Most of the existing studies on this topic rely on low-speed compressor cascade correlations from Carter or Lieblein. The aim of this work is to update those correlations for state-of-the-art controlled diffusion blades, and extend their application to high Mach number flow regimes more typical of modern compressors. Another objective is also to improve the physical understanding of the solidity effect on compressor performance and stability. A numerical investigation has been performed using the commercial software FINE/Turbo. Two different blade profiles were selected and investigated in the compressible flow regime as an extension to the low-speed data on which the correlations are based. The first cascade uses a standard double circular arc profile, extensively referenced in the literature, while the second configuration uses a state-of-the-art CDB, representative of low pressure compressor stator mid-span profile. Both profiles have been designed with the same inlet and outlet metal angles and the same maximum thickness but the camber and thickness distributions, the stagger angle and the leading edge geometry of the CDB have been optimized. The determination of minimum loss, optimum incidence and deviation is addressed and compared with existing correlations for both configurations and various Mach numbers that have been selected in order to match typical booster stall and choke operating conditions. The emphasis is set on the minimum loss performance at mid-span. The impact of the solidity on the operating range and the stability of the cascade are also studied.

Numerical Investigation of Passive Flow Control Using Wavy Blades in a Highly-Loaded Compressor Cascade

2018 ◽  
Author(s):  
Bo Wang ◽  
Yanhui Wu ◽  
Kai Liu
Keyword(s):  
Numerical Investigation ◽  
Flow Structure ◽  
Cross Flow ◽  
Leading Edge ◽  
Control Flow ◽  
Streamwise Vortices ◽  
Compressor Cascade ◽  
Control Effect ◽  
Suction Surface ◽  
Highly Loaded

Driven by the need to control flow separations in highly loaded compressors, a numerical investigation is carried out to study the control effect of wavy blades in a linear compressor cascade. Two types of wavy blades are studied with wavy blade-A having a sinusoidal leading edge, while wavy blade-B having pitchwise sinusoidal variation in the stacking line. The influence of wavy blades on the cascade performance is evaluated at incidences from −1° to +9°. For the wavy blade-A with suitable waviness parameters, the cascade diffusion capacity is enhanced accompanied by the loss reduction under high incidence conditions where 2D separation is the dominant flow structure on the suction surface of the unmodified blade. For well-designed wavy blade-B, the improvement of cascade performance is achieved under low incidence conditions where 3D corner separation is the dominant flow structure on the suction surface of the baseline blade. The influence of waviness parameters on the control effect is also discussed by comparing the performance of cascades with different wavy blade configurations. Detailed analysis of the predicted flow field shows that both the wavy blade-A and wavy blade-B have capacity to control flow separation in the cascade but their control mechanism are different. For wavy blade-A, the wavy leading edge results in the formation of counter-rotating streamwise vortices downstream of trough. These streamwise vortices can not only enhance momentum exchange between the outer flow and blade boundary layer, but also act as the suction surface fence to hamper the upwash of low momentum fluid driven by cross flow. For wavy blade-B, the wavy surface on the blade leads to a reduction of the cross flow upwash by influencing the spanwise distribution of the suction surface static pressure and guiding the upwash flow.

Hot-wire probes in low speed flow

1979 ◽  
Vol 18 ◽  
pp. 271-323 ◽  
Author(s):  
J.-D. Vagt
Keyword(s):  
Hot Wire ◽  
Low Speed ◽  
Speed Flow

A Study of Influences of Inlet Total Pressure Distortions On Clearance Flow in an Axial Compressor

2021 ◽  
Author(s):  
Guoming Zhu ◽  
Xiaolan Liu ◽  
Bo Yang ◽  
Moru Song
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Axial Compressor ◽  
Leading Edge ◽  
Stall Margin ◽  
Flow Cells ◽  
Static Pressure Distribution ◽  
Speed Flow ◽  
Clearance Flow ◽  
The Stability

Abstract The rotating distortion generated by upstream wakes or low speed flow cells is a kind of phenomenon in the inlet of middle and rear stages of an axial compressor. Highly complex inflow can obviously affect the performance and the stability of these stages, and is needed to be considered during compressor design. In this paper, a series of unsteady computational fluid dynamics (CFD) simulations is conducted based on a model of an 1-1/2 stage axial compressor to investigate the effects of the distorted inflows near the casing on the compressor performance and the clearance flow. Detailed analysis of the flow field has been performed and interesting results are concluded. The distortions, such as total pressure distortion in circumferential and radial directions, can block the tip region so that the separation loss and the mixing loss in this area are increased, and the efficiency and the total pressure ratio are dropped correspondingly. Besides, the distortions can change the static pressure distribution near the leading edge of the rotor, and make the clearance flow spill out of the rotor edge more easily under near stall condition, especially in the cases with co-rotating distortions. This phenomenon can be used to explain why the stall margin is deteriorated with nonuniform inflows.

Sign in / Sign up

Export Citation Format

Share Document