Determination of monaural sensitivity changes due to the pinna by use of minimum‐audible‐field measurements in the lateral vertical plane

1977 ◽  
Vol 61 (3) ◽  
pp. 820-828 ◽  
Author(s):  
P. Jeffrey Bloom
Keyword(s):  
Vertical Plane ◽  
Field Measurements ◽  
Sensitivity Changes

Experimental research control methods of the spatial position of building constructions

2017 ◽  
Vol 922 (4) ◽  
pp. 7-12 ◽  
Author(s):  
G.A. Shekhovtsov ◽  
R.P. Shekhovtsova ◽  
D.P. Ivenin ◽  
O.V. Raskatkina
Keyword(s):  
Simultaneous Determination ◽  
Experimental Research ◽  
Vertical Plane ◽  
Error Theory ◽  
Spatial Position ◽  
Bridge Crane ◽  
Building Structures ◽  
Control Methods ◽  
Engineering Geodesy

The article contains the method of discrete scanning points in the vertical plane of the columns and roof trusses for the simultaneous determination of vertical columns, the distance between them in flight at their tip and deflection farms with one point standing and only one performer. The technique is based on the use of reflectorless electronic tachymeter and its SDh key. Experimental research of methods on the elements of building structures NNGASU educational housing using electronic tachymeter SET530R. Results of the experiments were monitored by a coordinate and photographic methods, as well as with the developed at the chair of Engineering Geodesy laser-mirroring device designed to measure inaccessible or hard to reach distances. Analysis methods of error theory position and the results of its comparison with other methods have shown that it provides the required accuracy, easy to perform, does not require the output of the observer on the crane path or lift to the towers, free from the multiple engagement of the bridge crane and can be successfully applied on practice.

scholarly journals Laboratory and In Situ Determination of Hydraulic Conductivity and Their Validity in Transient Seepage Analysis

Water ◽  
2021 ◽  
Vol 13 (8) ◽  
pp. 1131
Author(s):  
Soonkie Nam ◽  
Marte Gutierrez ◽  
Panayiotis Diplas ◽  
John Petrie
Keyword(s):  
Hydraulic Conductivity ◽  
Field Measurements ◽  
Natural Soil ◽  
In Situ Tests ◽  
Seepage Analysis ◽  
Soil Deposits ◽  
Seepage Modeling ◽  
Sample Disturbance

This paper critically compares the use of laboratory tests against in situ tests combined with numerical seepage modeling to determine the hydraulic conductivity of natural soil deposits. Laboratory determination of hydraulic conductivity used the constant head permeability and oedometer tests on undisturbed Shelby tube and block soil samples. The auger hole method and Guelph permeameter tests were performed in the field. Groundwater table elevations in natural soil deposits with different hydraulic conductivity values were predicted using finite element seepage modeling and compared with field measurements to assess the various test results. Hydraulic conductivity values obtained by the auger hole method provide predictions that best match the groundwater table’s observed location at the field site. This observation indicates that hydraulic conductivity determined by the in situ test represents the actual conditions in the field better than that determined in a laboratory setting. The differences between the laboratory and in situ hydraulic conductivity values can be attributed to factors such as sample disturbance, soil anisotropy, fissures and cracks, and soil structure in addition to the conceptual and procedural differences in testing methods and effects of sample size.

Micro Roughness Determination Of Periodic Microelectronics Structures Using Optical Far Field Measurements

2011 ◽  
Author(s):  
Alexandre Vauselle ◽  
Philippe Maillot ◽  
Gaëlle Georges ◽  
Carole Deumié ◽  
David G. Seiler ◽  
...  
Keyword(s):  
Field Measurements ◽  
Far Field

Corrosion Metal Loss Interaction From In-Line Inspection and How it Can Affect the Calculated Failure Pressure

2012 ◽  
Author(s):  
Lucinda Smart ◽  
Richard McNealy ◽  
Harvey Haines
Keyword(s):  
Field Measurements ◽  
Metal Loss ◽  
Data Correlation ◽  
Failure Pressure ◽  
Industry Standards ◽  
Direct Measurements ◽  
Non Destructive ◽  
Flux Leakage

In-Line Inspection (ILI) is used to prioritize metal loss conditions based on predicted failure pressure in accordance with methods prescribed in industry standards such as ASME B31G-2009. Corrosion may occur in multiple areas of metal loss that interact and may result in a lower failure pressure than if flaws were analyzed separately. The B31G standard recommends a flaw interaction criterion for ILI metal loss predictions within a longitudinal and circumferential spacing of 3 times wall thickness, but cautions that methods employed for clustering of ILI anomalies should be validated with results from direct measurements in the ditch. Recent advances in non-destructive examination (NDE) and data correlation software have enabled reliable comparisons of ILI burst pressure predictions with the results from in-ditch examination. Data correlation using pattern matching algorithms allows the consideration of detection and reporting thresholds for both ILI and field measurements, and determination of error in the calculated failure pressure prediction attributable to the flaw interaction criterion. This paper presents a case study of magnetic flux leakage ILI failure pressure predictions compared with field results obtained during excavations. The effect of interaction criterion on calculated failure pressure and the probability of an ILI measurement underestimating failure pressure have been studied. We concluded a reason failure pressure specifications do not exist for ILI measurements is because of the variety of possible interaction criteria and data thresholds that can be employed, and demonstrate herein a method for their validation.

Real-time performance of filtering facepiece respirators at the workplace/Echtzeit-Performance partikelfiltrierender Halbmasken am Arbeitsplatz

Gefahrstoffe ◽  
2019 ◽  
Vol 79 (10) ◽  
pp. 378-384
Author(s):  
C. Sun ◽  
C. Thelen ◽  
I. Sancho Sanz ◽  
A. Wittmann
Keyword(s):  
Field Measurements ◽  
Paper Mill ◽  
Measuring System ◽  
Pilot Test ◽  
Protection Factor ◽  
Workplace Performance ◽  
Geometric Means ◽  
Training Facility ◽  
Workplace Conditions

The efficacy of a respirator under real workplace conditions is presented by its workplace protection factor (WPF). The aim of this study was to assess a portable measuring system for the determination of WPF for particulate filtering facepiece respirators. WPFs of CE-marked FFP2 and FFP3 filtering facepiece respirators were measured as a pilot test conducted at two workplaces: an inter-company training facility and a paper mill, with a total of seven test subjects. Each subject was quantitatively fit tested prior to the field measurements. Two TSI PortaCount instruments measured the particle concentrations simultaneously and continuously inside and outside the respirator for 15 min, with three repetitions. The results of the fit test (overall fit factor) ranged from 22 to 199. Individual WPF results ranged from 16 to 568 for FFP2 respirators, and from 13 to 232 for FFP3 respirators. The geometric means (GM) of the WPF were 135 with a 5th percentile value of 37 (FFP2), and 47 with a 5th percentile value of 12 (FFP3). This pilot test provides a new method of evaluating the workplace performance of filtering facepiece respirators.

scholarly journals A Study on Factors Influencing the Determination of Moisture Content of Fibrous Peat

2011 ◽  
Vol 2 (2) ◽  
pp. 39-47 ◽  
Author(s):  
Pui Tau Shien ◽  
Seneviratne H.N. ◽  
Dygku Salma Awg Ismail
Keyword(s):  
Moisture Content ◽  
Particle Density ◽  
Peat Soil ◽  
Test Procedure ◽  
Field Measurements ◽  
Standard Test ◽  
Moisture Loss ◽  
Fibrous Peat ◽  
Saturated Sample

Fibrous peat is an undrained peat that usually possesses very high moisture content. However, not all experimental procedures are applicable for determination of moisture content of fibrous peat. This research is aimed at examining the determination of insitu moisture content of fibrous peat using field measurements. The peat soil samples were collected at shallow depths from Asajaya at Kota Samarahan and Taman Kopodims at Matang , Kuching Sarawak by using peat auger. The laboratory tests such as determination of moisture content, fiber content, particle density and ash content were conducted on the collected samples in order to establish relationships between the parameters. Undisturbed peat samples from Matang were subjected to falling head permeability test to determine the saturated permeability. The saturated sample were then allowed to drain freely to simulate the moisture loss possible during sampling when samples were brought out of boreholes. The test results showed that moisture content varies according to the drying temperature and position of the soil sample (top, middle and bottom) during sampling. Comparing samples from both locations, peat soil from Kota Samarahan possessed higher moisture content. The saturated permeability of peat sample was in the range of 2.62 – 3.05 cm/s. The free draining trial showed that moisture loss during sampling significantly influence the moisture content measurement. The variation in value of moisture content for fibrous peat may occurs due to several factors such as existing ground water table, sampling method by boring, existing standard test procedure which is not suitable for peat soils requirement and also because of the physical properties which varied according to depth of soil.

scholarly journals Distance scaling method for accurate prediction of slowly varying magnetic fields in satellite missions

2016 ◽  
Vol 5 (2) ◽  
pp. 281-288 ◽  
Author(s):  
Panagiotis P. Zacharias ◽  
Elpida G. Chatzineofytou ◽  
Sotirios T. Spantideas ◽  
Christos N. Capsalis
Keyword(s):  
Signal To Noise Ratio ◽  
Near Field ◽  
Magnetic Behavior ◽  
Field Measurements ◽  
High Signal ◽  
Signal To Noise ◽  
Scaling Method ◽  
Magnetic Signature ◽  
The Magnetic Field

Abstract. In the present work, the determination of the magnetic behavior of localized magnetic sources from near-field measurements is examined. The distance power law of the magnetic field fall-off is used in various cases to accurately predict the magnetic signature of an equipment under test (EUT) consisting of multiple alternating current (AC) magnetic sources. Therefore, parameters concerning the location of the observation points (magnetometers) are studied towards this scope. The results clearly show that these parameters are independent of the EUT's size and layout. Additionally, the techniques developed in the present study enable the placing of the magnetometers close to the EUT, thus achieving high signal-to-noise ratio (SNR). Finally, the proposed method is verified by real measurements, using a mobile phone as an EUT.

Surface-groundwater interactions in karst: overview, concept and mapping

2021 ◽  
Author(s):  
Natasa Ravbar ◽  
Cyril Mayaud ◽  
Matej Blatnik ◽  
Metka Petrič
Keyword(s):  
Environmental Changes ◽  
Temporal Dynamics ◽  
Field Measurements ◽  
Spatial Dimension ◽  
Karst Aquifers ◽  
Wetland Ecosystems ◽  
Spatial And Temporal Dynamics ◽  
Ecohydrological Processes

<p>Under special meteorological and hydrological circumstances, shallow karst areas and karst poljes may experience surface water overflow. As a result, surface- groundwater interaction occurs usually creating intermittent lakes. Although human settlements and activities have traditionally adapted to these natural conditions, extensive temporary floods are classified among the most common natural disasters in karst. On the other hand, intermittent lakes are considered as natural reservoirs of excess recharge and good flood regulators in the lower parts of river basins. Due to specific ecohydrological processes and environmental conditions, these areas host unique wetland ecosystems with high levels of biodiversity and provide various ecosystem services, such as ecological productivity, photosynthesis and carbon storage. Given the dynamic nature of hydrological processes in karst aquifers, a distinctive feature of the phenomena described is its high variability of occurrence and duration. Therefore, the identification, characterization as well as the determination of the spatial dimension of flood levels is a challenging task. Focusing on the Slovenian karst, a literature review and analysis of topographical and hydrological data of the selected study areas was conducted. The hydrological analyses were based on long-term monitoring data from Slovenian Environmental Agency and partly on the authors' own database of field measurements and knowledge of the areas concerned. Consequently, the conceptual framework and the key criterion for the determination and recording of areas subject to temporary flooding were developed. A systematic survey reveals the significance of the extent, duration and frequency of flooding. Evaluation results are useful to designers of various water policies and management mechanisms for flood mitigation and protection of special habitats. Observing trends in the spatial and temporal dynamics of flood levels is also valuable for understanding how and to what extent karst aquifers are vulnerable to environmental changes. Finally, the analyses also enable prediction of the effects of these changes on other parts of the environment (e.g., hydrophilic habitats).</p>

Sign in / Sign up

Export Citation Format

Share Document