Ultrasonic thermography inspection method and apparatus

2007 ◽  
Vol 121 (2) ◽  
pp. 674
Author(s):  
Jeffrey G. Thompson ◽  
Clyde T. Uyehara
Keyword(s):  
Inspection Method ◽  
Ultrasonic Thermography

Analysis of Coliform and Colifecal Total Pollution Test on Various Types of Drinking Water Using the MPN (Most Probable Number) Method

2020 ◽  
Vol 2 (2) ◽  
Author(s):  
Wanda Aulya ◽  
Fadhliani Fadhliani ◽  
Vivi Mardina
Keyword(s):  
Drinking Water ◽  
Fecal Coliform ◽  
Pathogenic Bacteria ◽  
Microbiological Quality ◽  
Coliform Bacteria ◽  
Most Probable Number ◽  
Inspection Method ◽  
Sample Number ◽  
Probable Number ◽  
Fecal Coliform Bacteria

Water is the main source for life and also the most severe substance caused by pollution. The mandatory parameters for determining microbiological quality of drinking water are total non-fecal Coliform bacteria and Coliform fecal (Escherichia coli). Coliform bacteria are a group of microorganisms commonly used as indicators, where these bacteria can be a signal to determine whether a water source has been contaminated by bacteria or not, while fecal Coliform bacteria are indicator bacteria polluting pathogenic bacteria originating from human feces and warm-blooded animals (mammals) . The water inspection method in this study uses the MPN (Most Probable Number) method which consists of 3 tests, namely, the presumption test, the affirmation test, and the reinforcement test. The results showed that of 15 drinking water samples 8 samples were tested positive for Coliform bacteria with the highest total bacterial value of sample number 1, 15 (210/100 ml), while 7 other samples were negative. From 8 positive Coliform samples only 1 sample was stated to be negative fecal Coliform bacteria and 7 other samples were positive for Coliform fecal bacteria with the highest total bacterial value of sample number 1 (210/100 ml).

A Practical Ultrasonic Inspection Method for Detecting and Characterising Defects Found Within Composite Repairs

2018 ◽  
Author(s):  
J Downing ◽  
A Hook
Keyword(s):  
Wall Thickness ◽  
Steel Substrate ◽  
Ultrasonic Method ◽  
Ultrasonic Inspection ◽  
Heat Exposure ◽  
Matrix Cracking ◽  
Ultrasonic Technique ◽  
Inspection Method ◽  
Composite Repairs ◽  
Layered Matrix

Two steel substrate test panels were developed to represent common plate thicknesses found on naval vessels and scanned using the Babcock developed ultrasonic technique. One sample comprised of a series of slotted surface breaking flaws of varying widths and through thicknesses to represent fracturing/cracking. The inspection method detected simulated cracking to a depth of 2mm and 0.5mm in width. The second sample included numerous loss of wall thickness areas of varying diameters and through thicknesses, with the smallest detectable loss of wall thickness being 0.1mm at a 15mm diameter. After proving confidence in detection, there was a need to characterise flaws to provide support and ascertain a repair action. Samples were produced that were subjected to either impact or heat exposure to induce realistic representative damage. The practical ultrasonic method was successfully used to independently characterise between the samples, with induced de-laminations caused by blisters, and multi layered matrix cracking caused by varying levels of projectile impacts, due to their unique morphology.

Development of Wire Suspended Robot System (ARANEUS 2.0) for Bridge Inspection

10.29007/zw9k ◽  
2020 ◽  
Author(s):  
Kazuhide Nakata ◽  
Kazuki Umemoto ◽  
Kenji Kaneko ◽  
Ryusuke Fujisawa
Keyword(s):  
Unmanned Aerial Vehicle ◽  
Concrete Surface ◽  
Wire Length ◽  
High Definition ◽  
Bridge Inspection ◽  
Robot System ◽  
Inspection Method ◽  
Aerial Vehicle ◽  
The Wire

This study addresses the development of a robot for inspection of old bridges. By suspending the robot with a wire and controlling the wire length, the movement of the robot is realized. The robot mounts a high-definition camera and aims to detect cracks on the concrete surface of the bridge using this camera. An inspection method using an unmanned aerial vehicle (UAV) has been proposed. Compared to the method using an unmanned aerial vehicle, the wire suspended robot system has the advantage of insensitivity to wind and ability to carry heavy equipments, this makes it possible to install a high-definition camera and a cleaning function to find cracks that are difficult to detect due to dirt.

Impacts of Sample Preparation Methodology on TEM Failure Analysis of Advanced Semiconductor Devices

2011 ◽  
Author(s):  
Yongkai Zhou ◽  
Jie Zhu ◽  
Han Wei Teo ◽  
ACT Quah ◽  
Lei Zhu ◽  
...  
Keyword(s):  
Sample Preparation ◽  
Failure Analysis ◽  
Case Studies ◽  
Thickness Measurement ◽  
Interface Roughness ◽  
Silicide Formation ◽  
Cross Sectional ◽  
Inspection Method ◽  
Low Mass

Abstract In this paper, two failure analysis case studies are presented to demonstrate the importance of sample preparation procedures to successful failure analyses. Case study 1 establishes that Palladium (Pd) cannot be used as pre-FIB coating for SiO2 thickness measurement due to the spontaneously Pd silicide formation at the SiO2/Si interface. Platinum (Pt) is thus recommended, in spite of the Pt/SiO2 interface roughness, as the pre-FIB coating in this application. In the second case study, the dual-directional TEM inspection method is applied to characterize the profile of the “invisible” tungsten residue defect. The tungsten residue appears invisible in the planeview specimen due to the low mass-thickness contrast. It is then revealed in the cross-sectional TEM inspection.

Sign in / Sign up

Export Citation Format

Share Document