Resonant Response of a Tuning Fork

1950 ◽  
Vol 18 (3) ◽  
pp. 164-164
Author(s):  
Julius Sumner Miller
Keyword(s):  
Tuning Fork ◽  
Resonant Response

scholarly journals Development and Comparative Analysis of Electrochemically Etched Tungsten Tips for Quartz Tuning Fork Sensor

Micromachines ◽  
2021 ◽  
Vol 12 (3) ◽  
pp. 286
Author(s):  
Ashfaq Ali ◽  
Naveed Ullah ◽  
Asim Ahmad Riaz ◽  
Muhammad Zeeshan Zahir ◽  
Zuhaib Ali Khan ◽  
...  
Keyword(s):  
Tuning Fork ◽  
Mechanical Stability ◽  
Electrochemical Etching ◽  
Research Work ◽  
Cone Angle ◽  
Quartz Tuning Fork ◽  
Scanning Tunneling ◽  
Tunneling Microscopy ◽  
High Quality ◽  
Scanning Electron

Quartz Tuning Fork (QTF) based sensors are used for Scanning Probe Microscopes (SPM), in particular for near-field scanning optical microscopy. Highly sharp Tungsten (W) tips with larger cone angles and less tip diameter are critical for SPM instead of platinum and iridium (Pt/Ir) tips due to their high-quality factor, conductivity, mechanical stability, durability and production at low cost. Tungsten is chosen for its ease of electrochemical etching, yielding high-aspect ratio, sharp tips with tens of nanometer end diameters, while using simple etching circuits and basic electrolyte chemistry. Moreover, the resolution of the SPM images is observed to be associated with the cone angle of the SPM tip, therefore Atomic-Resolution Imaging is obtained with greater cone angles. Here, the goal is to chemically etch W to the smallest possible tip apex diameters. Tips with greater cone angles are produced by the custom etching procedures, which have proved superior in producing high quality tips. Though various methods are developed for the electrochemical etching of W wire, with a range of applications from scanning tunneling microscopy (SPM) to electron sources of scanning electron microscopes, but the basic chemical etching methods need to be optimized for reproducibility, controlling cone angle and tip sharpness that causes problems for the end users. In this research work, comprehensive experiments are carried out for the production of tips from 0.4 mm tungsten wire by three different electrochemical etching techniques, that is, Alternating Current (AC) etching, Meniscus etching and Direct Current (DC) etching. Consequently, sharp and high cone angle tips are obtained with required properties where the results of the W etching are analyzed, with optical microscope, and then with field emission scanning electron microscopy (FE-SEM). Similarly, effects of varying applied voltages and concentration of NaOH solution with comparison among the produced tips are investigated by measuring their cone angle and tip diameter. Moreover, oxidation and impurities, that is, removal of contamination and etching parameters are also studied in this research work. A method has been tested to minimize the oxidation on the surface and the tips were characterized with scanning electron microscope (SEM).

scholarly journals Investigating the Trackability of Silicon Microprobes in High-Speed Surface Measurements

Sensors ◽  
2021 ◽  
Vol 21 (5) ◽  
pp. 1557
Author(s):  
Min Xu ◽  
Zhi Li ◽  
Michael Fahrbach ◽  
Erwin Peiner ◽  
Uwe Brand
Keyword(s):  
Dynamic Model ◽  
High Speed ◽  
High Signal ◽  
Resonant Response ◽  
High Demand ◽  
Surface Measurements ◽  
Tactile Roughness ◽  
Low Mass ◽  
Roughness Measurements

High-speed tactile roughness measurements set high demand on the trackability of the stylus probe. Because of the features of low mass, low probing force, and high signal linearity, the piezoresistive silicon microprobe is a hopeful candidate for high-speed roughness measurements. This paper investigates the trackability of these microprobes through building a theoretical dynamic model, measuring their resonant response, and performing tip-flight experiments on surfaces with sharp variations. Two microprobes are investigated and compared: one with an integrated silicon tip and one with a diamond tip glued to the end of the cantilever. The result indicates that the microprobe with the silicon tip has high trackability for measurements up to traverse speeds of 10 mm/s, while the resonant response of the microprobe with diamond tip needs to be improved for the application in high-speed topography measurements.

Low-volume liquid delivery and nanolithography using a nanopipette combined with a quartz tuning fork-atomic force microscope

Nanoscale ◽  
2012 ◽  
Vol 4 (20) ◽  
pp. 6493 ◽  
Author(s):  
Sangmin An ◽  
Corey Stambaugh ◽  
Gunn Kim ◽  
Manhee Lee ◽  
Yonghee Kim ◽  
...  
Keyword(s):  
Atomic Force Microscope ◽  
Tuning Fork ◽  
Quartz Tuning Fork ◽  
Atomic Force ◽  
Low Volume ◽  
Liquid Delivery

A Resonant Response to Random Excitation

1979 ◽  
Vol 37 (2) ◽  
pp. 382-395
Author(s):  
H. Kurss ◽  
W. Vojir
Keyword(s):  
Random Excitation ◽  
Resonant Response
Sign in / Sign up

Export Citation Format

Share Document