TU-FG-201-08: Investigation of Systematic Low RPC Calibration Result for Tomotherapy

2016 ◽  
Vol 43 (6Part35) ◽  
pp. 3754-3754
Author(s):  
Q Chen
Keyword(s):  
Calibration Result

scholarly journals DISEMINASI RESISTOR STANDAR 1 KΩ KE STANDAR KERJA

2016 ◽  
Vol 17 (3) ◽  
pp. 223
Author(s):  
Muhammad Azzumar ◽  
Agah Faisal
Keyword(s):  
Uncertainty Estimation ◽  
Research Center ◽  
Working Standard ◽  
Degree Of Equivalence ◽  
Reference Resistor ◽  
Calibration Result ◽  
Measurement Results ◽  
Korea Research Institute ◽  
Research Institute

<p>Abstrak<br />Diseminasi nilai kalibrasi resistor standar kepada standar kerja di Puslit Metrologi - LIPI telah dilakukan. Hal ini bertujuan untuk mendapatkan hasil kalibrasi dan estimasi ketidakpastiannya yang valid dan tertelusur ke SI pada standar kerja. Desiminasi dilakukan dengan cara mengimplenmentasikan nilai kalibrasi resistor standar 1 kΩ ke resistor acuan dan kemudian ke standar kerja. Nilai yang telah diturunkan kepada standar kerja, reference multimeter, telah dibandingkan dengan nilai pengukuran yang dilakukan oleh KRISS (Korea Research Institute of Standards and Science) melalui kriteria derajat ekuivalensi. Error number berdasarkan kriteria derajat ekuivalensi antara Metrologi - LIPI dan KRISS pada resistor-resistor 100Ω, 10Ω, dan 1Ω masing-masing adalah sebesar 0,51, 0,73, dan 0,87. Berdasarkan error number tersebut, hasil pengukuran Metrologi - LIPI memiliki kesesuaian nilai ukur dengan hasil ukur KRISS. Lebih daripada itu, hal tersebut telah memvalidasi hasil kalibrasi dan estimasi ketidakpastian dari resistor acuan dan standar kerja di Puslit Metrologi - LIPI.<br />Kata kunci: nilai kalibrasi, resistor standar, standar kerja, kriteria derajat kebebasan, validasi.</p><p><br />Abstract<br />Dissemination of calibration value of standard resistor to working standard in Research Center for Metrology LIPI has been done. It aims to get the calibration result and the uncertainty estimation that are valid and traceable to SI on the working standard. The desimination was performed by implementing calibration value of 1 kΩ standard resistor to reference resistor and then to working standard. The value that had been disseminated to working standard, reference multimeter, had been compared to the measurement value made by KRISS (Korea Research Institute of Standards and Science) through a degree of equivalence criteria. The error numbers based on the degree of equivalence criteria between Metrology-LIPI and KRISS for the resistors measurement of 100Ω, 10Ω, and 1Ω were 0.51, 0.73, and 0.87 respectively. Based on those error numbers, Metrology-LIPI measurement results had the measuring value agreement with KRISS measurement results. Moreover, Its had validated calibration result and the uncertainty estimation of reference resistor and working standard in Metrology LIPI<br />Keywords: calibration value, standard resistor, working standard, degree of equivalence criteria, validation.</p>

scholarly journals Data Analysis and Calibration of Radiocarbon Dating Results from the Cemetery of the Marquises of Jin

Radiocarbon ◽  
2001 ◽  
Vol 43 (1) ◽  
pp. 55-62 ◽  
Author(s):  
Xiangyang Lu ◽  
Zhiyu Guo ◽  
Hongji Ma ◽  
Sixun Yuan ◽  
Xiaohong Wu
Keyword(s):  
Data Analysis ◽  
High Precision ◽  
Radiocarbon Dating ◽  
Careful Analysis ◽  
Historical Record ◽  
Calibration Result ◽  
Special Part ◽  
Peking University ◽  
Very High ◽  
Good Agreement

The chronology study of the cemetery of Marquises of Jin is valuable to improving the chronological table of Marquis of Jin family. It is also helpful for improving the chronological table of the Zhou Dynasty. The samples were measured at Peking University (PKUAMS). We also made an interlaboratory check with Isotrace to ensure the accuracy. By careful analysis of archaeological information, we built different models and calibrated by OxCal. The calibration results, both sampling contexts and estimations, are in very good agreement with the historical record. Because the dates of some events correspond to the special part of the curve, the calibration gets very high precision. The calibration result of tomb M93 suggests that its host is Marquis Shangshu instead of Marquis Wen.

Complete, Minimal and Continuous Kinematic Error Models of Perfect Multi-DOF Joints for Parallel Manipulators

2020 ◽  
Author(s):  
Lingyu Kong ◽  
Genliang Chen ◽  
Zhuang Zhang ◽  
Anhuan Xie ◽  
Hao Wang ◽  
...  
Keyword(s):  
Parallel Manipulators ◽  
Error Model ◽  
Parallel Robots ◽  
Kinematic Error ◽  
Kinematic Calibration ◽  
Calibration Result ◽  
Calibration Methods ◽  
Manufacturing Errors ◽  
The One ◽  
Serial Chains

Abstract Kinematic error model plays an important role in improving the positioning accuracy of robot manipulators by kinematic calibration. In order to get a better calibration result, the error model should satisfy complete, minimal and continuous criteria. In order to meet the complete requirement, the multi degree-of-freedom (DOF) joints, such as universal or spherical joint in parallel robots, have to be regarded as serial chains formed by multiple independent single DOF joints, such that the manufacturing errors of these joints can be considered. However, several previous work found that these manufacturing errors for some parallel manipulators have little effect on the accuracy improvement. Besides, considering these kind of errors will cause the kinematics to be much more complicated. Therefore, under the assumptions of perfectly manufactured universal, spherical and cylinder joints, a complete, minimal and continuous (CMC) error model is presented in this paper. The identifiability of the kinematic errors of these multi-DOF joints are analytically analyzed. In order to verify the correctness and effectiveness of the proposed method, a numerical simulation of kinematic calibration is conducted on a 6-UPS parallel manipulator. The calibration result is also compared to the one derived from the error model with 138 error parameters. Since the error model and calibration methods are described uniformly, it can be applied to most parallel manipulators.

A Calibration of a Feedwater Flowmeter Installed to Model Loop of a Nuclear Power Plant Using High Reynolds Number Facility

2008 ◽  
Author(s):  
Noriyuki Furuichi ◽  
Yoshiya Terao ◽  
Masaki Takamoto
Keyword(s):  
Reynolds Number ◽  
Power Plant ◽  
Nuclear Power Plant ◽  
Nuclear Power ◽  
High Reynolds Number ◽  
Tube Bundle ◽  
Three Dimensional ◽  
Calibration Result ◽  
Calibration Facility ◽  
High Reynolds

A calibration result of ultrasonic flowmeters using in a feedwater flowrate in a nuclear power plant, is described under a variety of upstream conditions using the new high Reynolds number calibration facility. The pipe layouts are classified to five type three-dimensional one with two or three elbows. The flow conditioners are tube bundle type and Mitsubishi type. Pipe Reynolds number is up to 1.6×107. The large effect of the flow conditioner and pipe layout is observed for cramp-on type. For multi-path type, individuality is observed.

scholarly journals Calibration of torque measurement under constant rotation in a wind turbine test bench

2019 ◽  
Vol 8 (1) ◽  
pp. 149-159 ◽  
Author(s):  
Paula Weidinger ◽  
Gisa Foyer ◽  
Stefan Kock ◽  
Jonas Gnauert ◽  
Rolf Kumme
Keyword(s):  
Measurement Uncertainty ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Test Bench ◽  
Calibration Procedure ◽  
National Standards ◽  
Torque Measurement ◽  
Transfer Standard ◽  
Calibration Result ◽  
Better Than

Abstract. To determine the efficiency of multi-MW wind turbines, the torque measurement in wind turbine test benches has to be performed with an accuracy better than 0.2 %. To this end, the torque measurement has to be traced to national standards in the MN m range. This can be done by using a novel torque transfer standard in combination with a newly developed torque calibration procedure under constant rotation, which are both presented and discussed in this paper. The calibration procedure was performed on a 4 MW wind turbine test bench and the evaluation of the calibration result, including a measurement uncertainty, is explained in detail.

A preliminary crossover calibration result for HY-2

2014 ◽  
Author(s):  
Yalong Liu ◽  
Youguang Zhang ◽  
Mingsen Lin ◽  
Junwu Tang
Keyword(s):  
Calibration Result

scholarly journals Calibration of Digital Thermometer using Sensor and Indicator Method

2020 ◽  
Vol 4 (9) ◽  
pp. 11-14
Keyword(s):  
Confidence Level ◽  
Indicator Method ◽  
Digital Thermometer ◽  
Serial Number ◽  
Calibration Result ◽  
K Factor

A Calibration has been done for digital thermometer using a sensor and indicator method. The unit under test manufactured by Fluke with 54-II type and serial number 13160058, meanwhile, the standards that used are PT100 sensor from Omega and an indicator from Additel. The calibration result from 12 setpoints shows the average correction value as 0.61 ºC with uncertainty as 0.32 ºC and K factor as 2.0 at 95% confidence level

Sign in / Sign up

Export Citation Format

Share Document