Measurement Of Flame Temperature Distribution In A Diesel Engine By Means Of Image Analysis Of High Speed Photographs

1979 ◽  
Author(s):  
S. K. Ahn ◽  
Y. Matsui ◽  
T. Kamimoto ◽  
S. Matsuoka ◽  
S. Nagano
Keyword(s):  
Image Analysis ◽  
Diesel Engine ◽  
Temperature Distribution ◽  
High Speed ◽  
Flame Temperature

scholarly journals Measurement of flame temperature and soot amount for effective NOx and PM reduction in a heavy duty diesel engine

2019 ◽  
Vol 179 (4) ◽  
pp. 32-39
Author(s):  
Yuzo AOYAGI
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
High Speed ◽  
Flame Temperature ◽  
Video Camera ◽  
Boost Pressure ◽  
Diesel Combustion ◽  
Single Cylinder ◽  
Wide Range ◽  
Kl Factor

To reduce exhaust NOx and smoke, it is important to measure flame temperature and soot amount in combustion chamber. In diesel combustion it is effective to use the two-color method for the measurement of the flame temperature and KL factor, which is related with soot concentration. The diesel flame was directly and continuously observed from the combustion chamber at running engine condition by using a bore scope and a high-speed video camera. The experimental single cylinder engine has 2.0-liter displacement and has the ability with up to five times of the boost pressure than the naturally aspirated engine by external super-charger. The devices of High Boost, Wide Range and High EGR rate at keeping a relatively high excess air ratio were installed in this research engine in order to reduce exhaust NOx emission without smoke deterioration from diesel engines. The video camera nac GX-1 was used in this study. From observed data under the changing EGR rates, the flame temperature and KL factor were obtained by the software of two-color method analysis. The diesel combustion processes are understood well by analyzing high-speed movies of the diesel flame motion and its temperature. The NOx and smoke are mutually related to maximum flame temperature and also it is possible to reduce simultaneously both NOx and soot emissions by high EGR rate in a single cylinder diesel engine.

Measurement of Flame Temperature Distribution in D.I. Diesel Engine with High Pressure Fuel Injection

1992 ◽  
Author(s):  
Shinji Kobayashi ◽  
Takayuki Sakai ◽  
Toshio Nakahira ◽  
Masanori Komori ◽  
Kinji Tsujimura
Keyword(s):  
High Pressure ◽  
Diesel Engine ◽  
Temperature Distribution ◽  
Fuel Injection ◽  
Flame Temperature

High-speed brightfield 3-D imaging and 3-D image analysis of thick and overlapped cell clusters in cytological preparations

1994 ◽  
Vol 52 ◽  
pp. 218-219
Author(s):  
Robert W. Mackin
Keyword(s):  
Image Analysis ◽  
High Speed ◽  
Three Dimensional ◽  
Image Data ◽  
Ccd Camera ◽  
Objective Lens ◽  
Array Processor ◽  
Vaginal Smears ◽  
Low Contrast ◽  
Computer Controlled

This paper presents two advances towards the automated three-dimensional (3-D) analysis of thick and heavily-overlapped regions in cytological preparations such as cervical/vaginal smears. First, a high speed 3-D brightfield microscope has been developed, allowing the acquisition of image data at speeds approaching 30 optical slices per second. Second, algorithms have been developed to detect and segment nuclei in spite of the extremely high image variability and low contrast typical of such regions. The analysis of such regions is inherently a 3-D problem that cannot be solved reliably with conventional 2-D imaging and image analysis methods.High-Speed 3-D imaging of the specimen is accomplished by moving the specimen axially relative to the objective lens of a standard microscope (Zeiss) at a speed of 30 steps per second, where the stepsize is adjustable from 0.2 - 5μm. The specimen is mounted on a computer-controlled, piezoelectric microstage (Burleigh PZS-100, 68/μm displacement). At each step, an optical slice is acquired using a CCD camera (SONY XC-11/71 IP, Dalsa CA-D1-0256, and CA-D2-0512 have been used) connected to a 4-node array processor system based on the Intel i860 chip.

scholarly journals Research on the Ignition Height and Reaction Flame Temperature of PTFE/Al/Si/CuO with Different Mass Ratios of PTFE/Si

Materials ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3464
Author(s):  
Xuan Zou ◽  
Jingyuan Zhou ◽  
Xianwen Ran ◽  
Yiting Wu ◽  
Ping Liu ◽  
...  
Keyword(s):  
Energy Release ◽  
High Speed ◽  
Flame Temperature ◽  
Sintering Process ◽  
Release Process ◽  
Reactive Material ◽  
Temperature Changes ◽  
Release Capacity ◽  
Mass Ratios ◽  
The Relationship

Recent studies have shown that the energy release capacity of Polytetrafluoroethylene (PTFE)/Al with Si, and CuO, respectively, is higher than that of PTFE/Al. PTFE/Al/Si/CuO reactive materials with four proportions of PTFE/Si were designed by the molding–sintering process to study the influence of different PTFE/Si mass ratios on energy release. A drop hammer was selected for igniting the specimens, and the high-speed camera and spectrometer systems were used to record the energy release process and the flame spectrum, respectively. The ignition height of the reactive material was obtained by fitting the relationship between the flame duration and the drop height. It was found that the ignition height of PTFE/Al/Si/CuO containing 20% PTFE/Si is 48.27 cm, which is the lowest compared to the ignition height of other Si/PTFE ratios of PTFE/Al/Si/CuO; the flame temperature was calculated from the flame spectrum. It was found that flame temperature changes little for the same reactive material at different drop heights. Compared with the flame temperature of PTFE/Al/Si/CuO with four mass ratios, it was found that the flame temperature of PTFE/Al/Si/CuO with 20% PTFE/Si is the highest, which is 2589 K. The results show that PTFE/Al/Si/CuO containing 20% PTFE/Si is easier to be ignited and has a stronger temperature destruction effect.

Sign in / Sign up

Export Citation Format

Share Document